Page 2
INTRODUCTION Thank you for purchasing the 2-in-1 Ride & Balance Scooter! Easily transforms from 3 wheeled trike to 2 wheeled balance bike. Interactive headlight and roller map get little ones moving by encouraging them to ‘ride’ to different destinations. On/Off/Volume Switch Twisting Headlight Ring Rolling Map Light Up Buttons...
INCLUDED IN THE PACKAGE Short Axel Long Axel Two Back Wheels Seat Back Handle Front Wheel Front Wheel Cover Driving Panel Four Screws Two Handlebars Driving Panel Scooter Body Label Sheet Support Post • Quick Start Guide...
Page 4
WARNING All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your child’s safety. NOTE Please save this Instruction Manual as it contains important information.
GETTING STARTED WARNING: Adult assembly required for battery installation. Keep batteries out of reach of children. Battery Removal and Installation 1. Make sure the unit is turned OFF. 2. Locate the battery cover on the back of the unit. Use a screwdriver to loosen the screw and then open the battery cover.
Page 7
In the UK, give this toy a second life by disposing of it at a small electricals collection point* so all of its materials can be recycled. Learn more at: www.vtech.co.uk/recycle www.vtech.com.au/sustainability * Visit www.recyclenow.com to see a list of collection points near you.
Page 8
ASSEMBLY INSTRUCTIONS With the 2-in-1 Ride & Balance Scooter safety comes first. To ensure your child’s safety, adult assembly is required. For your child’s safety, do not let your child play with the toy until it is fully assembled. 1. Insert the Seat Back Handle into the slots on the back of the Seat.
Page 9
4. Attach the Driving Panel Support Post to the bottom of the Driving Panel, securing the pieces together with the four Small Screws. 5. Insert the Front Wheel into the bottom of the Scooter Body. Push until you hear the Front Wheel snap into place. 6.
Page 10
7. To remove the Back Wheels, slide and hold the Wheel Lock while pulling out the Small Axel. Next, slide and hold the Wheel Lock and pull out the Long Axel, then remove and separate the two Wheels. 8. To assemble the Back Wheels in the Tricycle position, slide the Short Axel through the outside of one of the Wheels, then through the corresponding hole in one of the Scooter’s Wheel Supports.
9. Please check the Wheel Locks before using the scooter. The Wheel Locks will spring into the locked position when the Wheel Axels are properly installed. PRODUCT FEATURES 1. On/Off/Volume Switch To turn the unit On, turn the On/Off/ Volume Switch to the Low volume or High volume position.
Page 12
2. Rolling Map Turn the Rolling Map to one of the four positions to identify the locations through fun phrases and sounds associated with the locations. The lights will flash with the sounds. 3. Twisting Headlight Ring Turn the Twisting Headlight Ring to hear a variety of fun sounds.
12. Skip to My Lou 13. Do You Know the Muffin Man? 14. Here We Go Round the Mulberry Bush 15. While Strolling Through the Park 16. The Alphabet Song SONG LYRICS Song 1 Are you ready? Are you ready? Time to ride, time to ride.
TROUBLESHOOTING If for some reason the unit stops working or malfunctions, please follow these steps: 1. Turn the unit Off. 2. Interrupt the power supply by removing the batteries. 3. Let the unit stand for a few minutes, then replace the batteries. 4.
Read our complete warranty policy online at vtech.co.uk/warranty. Australian Customers: VTECH ELECTRONICS (AUSTRALIA) PTY LIMITED – CONSUMER GUARANTEES Under the Australian Consumer Law, a number of consumer guarantees apply to goods and services supplied by VTech Electronics (Australia) Pty Limited. Please refer to vtech.com.au/consumerguarantees for further information.
Need help?
Do you have a question about the 572353 and is the answer not in the manual?
Questions and answers