Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Tool Shed TSCS8
- Page 1 CHAINSAW 18IN 52CC TSCS8 www.thetoolshed.co.nz...
-
Page 2: Table Of Contents
OPERATION MANUAL TABLE OF CONTENTS PRODUCT DETAILS Product Details Product Model ToolShed Chainsaw 18in 52cc Specifications Product Identification Product Code TSCS8 Safety Guidelines Kickback Safety Assembly Fuel & Chain Oil Operation Sawing DISTRIBUTED BY: Maintenance Saw Bar & Chain Maintenance... -
Page 3: Specifications
OPERATION MANUAL OPERATION MANUAL SPECIFICATIONS PRODUCT IDENTIFICATION Mass (Without Guide Bar & Chain) 5.50 kg Dimensions (Without Guide Bar & Chain) 41 x 235 x 265 mm Fuel Mixture 25:1 (Gasoline 25: Two-Stroke oil 1 ) Fuel Tank Capacity 550ml Chain Oil Motor Oil SAE 10W-30 Oil Tank Capacity... -
Page 4: Safety Guidelines
OPERATION MANUAL OPERATION MANUAL SAFETY GUIDELINES SAFETY GUIDELINES Fuel & Engine Safety Gasoline & Vapours from moving parts in the machine, or they WARNING could become caught therein. • Engine exhaust contains carbon monoxide, a • Always remain alert and DO NOT operate colourless, odourless, poison gas. - Page 5 OPERATION MANUAL OPERATION MANUAL SAFETY GUIDELINES SAFETY GUIDELINES When Adding or Removing Power Tool & Machinery Use & Service Chainsaw Specific Safety Gasoline Care • • Have your tools and machinery serviced Never operate a chain saw when you are at The ToolShed with ToolShed replace- fatigued, ill, upset, or under the influence of •...
-
Page 6: Kickback Safety
OPERATION MANUAL OPERATION MANUAL SAFETY GUIDELINES KICKBACK SAFETY • Chainsaw Specific Safety (Cont.) User Kickback Reduction Kickback may also occur during limbing. The greater the force of the kickback reaction, the • • Always shut off the engine before setting it Kickback may occur when the nose or tip of more difficult it becomes for the operator to down. -
Page 7: Assembly
OPERATION MANUAL OPERATION MANUAL ASSEMBLY FUEL & CHAIN OIL • What’s in the Box NOTE: A new chain will expand its length in If you use a gasoline of a lower octane value the beginning of use. Check and readjust the than prescribed, there is a danger that the tension frequently as a loose chain can easily engine temperature may rise and an engine... -
Page 8: Operation
OPERATION MANUAL OPERATION MANUAL FUEL & CHAIN OIL OPERATION Fuelling the Unit Engine Life WARNING • Untwist and remove the fuel cap. Rest the To extend the life of your engine, avoid the cap on a dustless surface. following: 1 = Choke knob: It is very dangerous to run a chainsaw A = When the engine •... -
Page 9: Checking The Oil Supply
OPERATION MANUAL OPERATION MANUAL OPERATION OPERATION Starting the Engine (Cont.) When adjusting, take the following steps: WARNING WARNING “H” and “L” needles are restricted within the WARNING number of turn as shown below. Keep clear of the saw chain as it will Be sure to confirm brake operation “H”... -
Page 10: Carburettor Anti-Freeze Mechanism
OPERATION MANUAL OPERATION MANUAL OPERATION SAWING Carburettor Anti-Freeze How to Switch Between forward. The chain should stop immediately WARNING Mechanism Operating Modes with the engine at full speed. If the chain is slow to Stop, or does not stop, replace the •... -
Page 11: Cutting Procedure Basics
OPERATION MANUAL OPERATION MANUAL SAWING SAWING Holding the Saw (Cont.) Cutting Procedure Basics Felling a Tree Then, make a vertical cut into the buttress root. • • • Grip the front handle using your left hand, Start the unit by following the instructions Do not fell trees with an extreme lean. - Page 12 OPERATION MANUAL OPERATION MANUAL SAWING SAWING Making the Felling Back Cut Limbing Cutting Logs Under Stress retreat path while keeping an eye on the falling tree. • This cut will fell the tree. Limbing is the process of removing branches When logs are held up at one or both ends, Cut horizontally on the opposite side of the the wood may bend as you cut, potentially...
- Page 13 OPERATION MANUAL OPERATION MANUAL SAWING SAWING Pruning Cutting Logs Under Stress Overbucking (Cont.) Begin cutting from above, with the bottom Pruning involves removing branches from a of the saw chain against the top of the log living tree. Follow these steps: (See Overbucking Figure).
-
Page 14: Periodic Maintenance
OPERATION MANUAL OPERATION MANUAL MAINTENANCE PERIODIC MAINTENANCE • Oiling Port Cylinder Fins Spark Plug Before cleaning or performing any mainte- nance, you must ensure the tool is switched • • • After each use, dismount the guide bar and Dust clogging between the cylinder fins will Clean the electrodes with a wire brush and off and disconnected from the power supply. -
Page 15: Saw Bar & Chain Maintenance
OPERATION MANUAL OPERATION MANUAL SAW BAR & CHAIN MAINTENANCE SAW BAR & CHAIN MAINTENANCE • Saw Chain Guide Bar After each cutter has been filed, check the depth gauge and file it to the proper level as • Reverse the bar occasionally to prevent partial wear. WARNING illustrated. -
Page 16: Troubleshooting
OPERATION MANUAL TROUBLESHOOTING FAULT POSSIBLE CAUSE SUGGESTED SOLUTION Check fuel for water or substandard Replace with proper fuel. Starting Failure mixture Remove and dry the spark plug. WARNING: Make sure the Check for engine flooding Then pull the starter again with icing prevention system is no choke.
Need help?
Do you have a question about the TSCS8 and is the answer not in the manual?
Questions and answers