Murata GCQ1555C1H3R9BB01 Series Reference Sheet

Only reflow soldering high q chip multilayer ceramic capacitors for automotive

Hide thumbs

page of 27

/ 27
Bookmarks

Quick Links

Download this manual

Only Reflow Soldering

High Q Chip Multilayer Ceramic Capacitors for Automotive

GCQ1555C1H3R9BB01_ (0402, C0G:EIA, 3.9pF, DC50V)

_: packaging code

1.Scope

This product specification is applied to High Q Chip Multilayer Ceramic Capacitors used for Automotive Electronic equipment.

This product is applied for Only Reflow Soldering.

2.MURATA Part NO. System

(Ex.)

GCQ

(1)L/W

Dimensions

3. Type & Dimensions

(1)-1 L

(1)-2 W

1.0±0.05

0.5±0.05

4.Rated value

(3) Temperature Characteristics

(Public STD Code):C0G(EIA)

Temp. coeff

or　Cap. Change

0±30 ppm/°C

5.Package

mark

(8) Packaging

f180mm Reel

PAPER W8P2

f180mm Reel

PAPER W8P1

f330mm Reel

PAPER W8P2

Product specifications in this catalog are as of Jul.11,2017,and are subject to change or obsolescence without notice.

Please consult the approval sheet before ordering.

Please read rating and !Cautions first.

GCQ1555C1H3R9BB01-01

(2)T

(3)Temperature

Dimensions

Characteristics

(2) T

0.5±0.05

0.15 to 0.35

(4)

Rated

Temp. Range

Voltage

(Ref.Temp.)

25 to 125 °C

DC 50 V

(25 °C)

Packaging Unit

10000 pcs./Reel

20000 pcs./Reel

50000 pcs./Reel

Downloaded From

3R9

(4)Rated

(6)Capacitance

(5)Nominal

Voltage

Tolerance

Capacitance

(Unit:mm)

0.3 min.

Specifications and Test

(6)

(5) Nominal

Capacitance

Tolerance

3.9 pF

±0.1 pF

Oneyac.com

Reference Sheet

B01

(7)Murata's Control

(8)Packaging Code

Code

Methods

(Operating

Temp. Range)

-55 to 125 °C

Need help?

Do you have a question about the GCQ1555C1H3R9BB01 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Murata GCQ1555C1H3R9BB01 Series

Page 1 _: packaging code Reference Sheet 1.Scope This product specification is applied to High Q Chip Multilayer Ceramic Capacitors used for Automotive Electronic equipment. This product is applied for Only Reflow Soldering. 　　 2.MURATA Part NO. System (Ex.) (1)L/W (2)T (4)Rated (7)Murata’s Control...
Page 2 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method Pre-and Post-Stress Electrical Test 2 High Temperature The measured and observed characteristics should satisfy the Solder the capacitor on the test board (glass epoxy board). Exposure (Storage) specifications in the following table.
Page 3 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method The measured and observed characteristics should satisfy the 7 Operational Life Solder the capacitor on the test board (glass epoxy board). specifications in the following table.
Page 4 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 14 Thermal Shock The measured and observed characteristics should satisfy the Solder the capacitor on the test board (glass epoxy board). specifications in the following table.
Page 5 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 18 Board Flex Appearance No marking defects Solder the capacitor on the test jig (glass epoxy board) shown in Fig1. ｺﾝﾃﾞﾝｻ Then apply a force in the direction shown in Fig 2 for 60s.
Page 6 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 21 Capacitance Temperature Nominal values of the temperature coefficient is The capacitance change should be measured after 5 minutes at each specified temp. stage. Characteristics shown in Rated value.
Page 7 Package GCQ Type 1.Tape Carrier Packaging(Packaging Code:D/E/W/J/F) 1.1 Minimum Quantity(pcs./reel) Paper Tape φ180mm reel φ330mm reel Type Code:D/E Code:W Code:J/F GCQ15 10000(W8P2) 20000(W8P1) 50000(W8P2) 1.2 Dimensions of Tape (1)GCQ15(W8P2 CODE:D/E/J/F) (in mm) *1,*2：2.0±0.05 4.0±0.1 +0.1 φ1.5 ＡＡ 0.05 max. Dimensions(Chip) Type A *3...
Page 8 詰め状態 ( 単位： mm) Package GCQ Type (in mm) Fig.1 Package Chips Chip Fig.2 Dimensions of Reel 2.0±0.5 φ21±0.8 Fig.3 Taping Diagram 16.5 max. 10±1.5 Top Tape : Thickness 0.06 Feeding Hole :As specified in 1.2. Hole for Chip : As specified in 1.2. Bottom Tape :Thickness 0.05 (Only a bottom tape existence ) Base Tape : As specified in 1.2.
Page 9 Package GCQ Type ﾌﾟ詰め状態 ( 単位： mm) 1.3 Tapes for capacitors are wound clockwise shown in Fig.3. (The sprocket holes are to the right as the tape is pulled toward the user.) 1.4 Part of the leader and part of the vacant section are attached as follows. (in mm) Tail vacant Section Chip-mounting Unit...
Page 10: Limitation Of Applications
Caution ■Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability 　 for the prevention of defects which might directly cause damage to the third party's life, body or property. 　　　①Aircraft equipment ②Aerospace equipment ③Undersea equipment ④Power plant control equipment...
Page 11 Caution 2.Measurement of Capacitance 1. Measure capacitance with the voltage and frequency specified in the product specifications. 1-1. The output voltage of the measuring equipment may decrease occasionally when capacitance is high. Please confirm whether a prescribed measured voltage is impressed to the capacitor. 1-2.
Page 12 Caution 5. DC Voltage and AC Voltage Characteristic 1. The capacitance value of a high dielectric constant type [Example of DC Voltage Characteristics] capacitor changes depending on the DC voltage applied. 0.1μF, Rated Voltage 50VDC Sample: X7R(R7) Characteristics Please consider the DC voltage characteristics when a capacitor is selected for use in a DC circuit.
Page 13 Caution ■Soldering and Mounting 1.Mounting Position 1. Confirm the best mounting position and direction that minimizes the stress imposed on the capacitor during flexing or bending the printed circuit board. 1-1.Choose a mounting position that minimizes the stress imposed on the chip during flexing or bending of the board. 　...
Page 14 Caution 3.Maintenance of the Mounting (pick and place) Machine 1. Make sure that the following excessive forces are not applied to the capacitors. Check the mounting in the actual device under actual use conditions ahead of time. 1-1. In mounting the capacitors on the printed circuit board, any bending force against them shall be kept to a minimum to prevent them from any damage or cracking.
Page 15 Caution 4-1.Reflow Soldering 1. When sudden heat is applied to the components, the [Standard Conditions for Reflow Soldering] mechanical strength of the components will decrease because a sudden temperature change causes deformation inside the components. In order to prevent Temperature(℃) mechanical damage to the components, preheating is Soldering Peak Temperature...
Page 16 Caution 4-2.Flow Soldering 1. This product is not apply flow soldering. 4-3.Correction of Soldered Portion When sudden heat is applied to the capacitor, distortion caused by the large temperature difference occurs internally, and can be the cause of cracks. Capacitors also tend to be affected by mechanical and thermal stress depending on the board preheating temperature or the soldering fillet shape, and can be the cause of cracks.
Page 17 Caution 5.Washing Excessive ultrasonic oscillation during cleaning can cause the PCBs to resonate, resulting in cracked chips or broken solder joints. Before starting your production process, test your cleaning equipment / process to insure it does not degrade the capacitors. 6.Electrical Test on Printed Circuit Board 1.
Page 18 Caution (1) Example of a suitable jig [In the case of Single-side Mounting] An outline of the board separation jig is shown as follows. Recommended example: Stress on the component mounting position can be minimized by holding the portion close to the jig, and bend in the direction towards the side where the capacitors are mounted. Not recommended example: The risk of cracks occurring in the capacitors increases due to large stress being applied to the component mounting position, if the portion away from the jig is held and bent in the direction opposite the side where the capacitors are mounted.
Page 19 Caution (3) Example of Router Type Separator [ Outline Drawing ] Router The router type separator performs cutting by a router rotating at a high speed. Since the board does not bend in the cutting process, stress on the board can be suppressed during board separation.
Page 20 Caution ■ Others 1. Under Operation of Equipment 1-1. Do not touch a capacitor directly with bare hands during operation in order to avoid the danger of an electric shock. 1-2. Do not allow the terminals of a capacitor to come in contact with any conductive objects (short-circuit). Do not expose a capacitor to a conductive liquid, inducing any acid or alkali solutions.
Page 21 Notice ■ Rating 1.Operating Temperature 1. The operating temperature limit depends on the capacitor. 1-1. Do not apply temperatures exceeding the maximum operating temperature. It is necessary to select a capacitor with a suitable rated temperature that will cover the operating temperature range. It is also necessary to consider the temperature distribution in equipment and the seasonal temperature variable factor.
Page 22 Notice ■Soldering and Mounting 1.PCB Design 1. Notice for Pattern Forms 1-1. Unlike leaded components, chip components are susceptible to flexing stresses since they are mounted directly on the substrate. They are also more sensitive to mechanical and thermal stresses than leaded components. Excess solder fillet height can multiply these stresses and cause chip cracking.
Page 23 Notice 2. Land Dimensions Chip Capacitor 　Please confirm the suitable land dimension by Land evaluating of the actual SET / PCB. Solder Resist Table 1 Reflow Soldering Method Chip(L×W) Chip　Dimension Series (Dimensions (L/W)　Code Tolerance) 1.0×0.5 0.3 to 0.5 0.35 to 0.45 0.4 to 0.6 (±0.05) (in mm)
Page 24 Notice 2.Reflow soldering The halogen system substance and organic acid are included in solder paste, and a chip corrodes 　 by this kind of solder paste. Do not use strong acid flux. Do not use water-soluble flux.* (*Water-soluble flux can be defined as non-rosin type flux including wash-type flux and non-wash-type flux.) 3.Washing 1.
Page 25 Notice ■ Others 1.Transportation 1. The performance of a capacitor may be affected by the conditions during transportation. 1-1. The capacitors shall be protected against excessive temperature, humidity and mechanical force during transportation. (1) Climatic condition 　･ low air temperature : -40℃ ･...
Page 26 NOTE 1.Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2.Your are requested not to use our product deviating from this product specification. 3.We consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents.
Page 27 单击下面可查看定价，库存，交付和生命周期等信息 >>Murata(村田) Downloaded From Oneyac.com...

This manual is also suitable for:

Gcq1555c1h3r9bb01d