Advertisement
Quick Links
Mount
Cantilever Series
Installation Guide
Every effort has been made to provide accurate
and error-free assembly and installation.
DCS Mount disclaims liability for any difficulties
arising from the interpretation of information
contained in these instructions.
If DCS Mount products are used for purposes other
than their original intent. DCS Mount, its distributors
and retailers shall not be held responsible or liable
for injuries or property damage, direct indirect, or
consequential, which may arise from the inability
to use this product safely, properly, and in the manner
for which it has been designed and manufactured.
Warranty does not apply to products, which hav e be en
l o s t , d a m a g e d b y m i s u s e , a b u s e , o r a c c i d e n t .
Thank you for choosing DCS Mount
Fly your Flat Panel TV
Advertisement
Summary of Contents for DCS Flat Panel TV
-
Page 1: Installation Guide
DCS Mount disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If DCS Mount products are used for purposes other than their original intent. DCS Mount, its distributors and retailers shall not be held responsible or liable... - Page 2 Illustration for hardware kit LP-80 Flat Panel Cantilever Mount Installation Instructions 80 lb. Maximum weight capacity VESA 75/100 compliant Cantilever arm mount for large LCD and small plasma panels Allows maximum flexibility for installing and viewing displays. Cantilever arm provides full extension and 180 of lateral rotation for viewing from multiple locations.
- Page 3 Contact your dealer or contact DCS Mount to find out if an adapter is available for your monitor. All plasma will require an adapter bracket. You will need someone to help with this installation.
- Page 4 5. All of the screws are properly torqued to specification when the unit is assembled at the factory and should not need an further initial adjustments. However, due to the variety in size of different monitors, MINOR adjustment may be required to optimize the tension needed for ease of movement.
- Page 5 Mounting the Wall Plate Mounting to Wooden Stud 1. Determine the location where you want the display mounted on the wall. 2. USE stud finder to locate and mark the center of the two studs. 3. Remove P-150 from box. Remove the PA-4260 Adaptor plate from the Mounting Head, and set the four 3/8-16 button head screws aside for later.
- Page 6 Mounting Cantilever Assembly 1. Important: for the display to be centered over the wall plate when the cantilever arm is folded, the arm will need to be offset by approximately 4”(10.1cm) from the desired center position of the screen. To do this, first not where the desired center of screen position intersects the wall plate, and then mark the all plate.
- Page 7 Configuring the PA-4260 adaptor plate (Installation instructions) PA-4260 Universal Plasma TV Adaptor Installation Instructions Fully adjustable design fits most large flat panel displays Includes complete hardware kit Quick mount capability with P-150 Durable grey or black powder coat finish Check the Hare Ware Kit after open the package Description N/A Button Head Screw 1/4-20 x 1/2 N/A Washer 1/4 ID X 1/2 OD...
- Page 8 Set PA-4260 width The PA-4260 is capable of handling a wide range of landed insert widths. Measure the horizontal distance between mounting lands on your display, and set the width of the Mounting Rails as shown, Standard Range: 38 1/2”(98 cm) to 15 3/4”(40 cm) Standard Configuration For standard range configurations, loosen the screws on the sliders using the supplied Hex Wrench;...
- Page 9 Mount PA-4260 to Display Hardware Selection a. Consult the supplied Hardware Cross Reference list. b. Select the mounting hardware for your display. Attach PA-4260 to Display a. Position the PA-4260 over back of display. b. Thread mounting screws through square washers and spacers (if required), as shown. c.
- Page 10 Mounting the display 1. Locate the set of four 3/8”-16 button head cap screws removed at the beginning of the installation. 2. Thread two of the screws approximately a 1/4”(0.6cm) into the upper set of PEM nuts on the adaptor plate, as shown 3.
- Page 11 Vertical Tilt Function – raising and lowering the screen edge to improve viewing angle/picture quality. Operation – Loosen tilt tension screws with supplied 3/16” Hex wrench as shown. Adjust display for desired tilt angle. Re-tighten tension screws. CAUTION : It is important to try to maintain even torque on each of the 4 screws.
- Page 12 NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE DCS Mount Fastener Part ID dia x length 5mm x 15 8mm x 20* M8 x 35 8mm x 35 6mm x 35 5mm x 15 5mm x 15...
- Page 13 5/8 x1 5/8 x1 5/8 x1 5/8 x1 5/8 x1 5/8 x1 5/8 x1 5/8 x1 5/8 x1 DCS Mount Fastener Part ID dia x length 6mm x 16 6mm x 16 6mm x 16 6mm x 16 6mm x 16...
- Page 14 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 NONE NONE NONE NONE NONE NONE DCS Mount Fastener Part ID dia x length 5mm x 15 5mm x 15 5mm x 15 5mm x 15 5mm x 15 5mm x 15...
- Page 15 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 3/4 x 3/8 DCS Mount Fastener Part ID dia x length 8mm x 20* 8mm x 20* 8mm x 20* 8mm x 20*...
- Page 16 5/8 x 1 NONE NONE NONE NONE NONE NONE NONE NONE NONE DCS Mount Fastener Part ID dia x length 8mm x 35 8mm x 35 8mm x 35 8mm x 35 8mm x 35 8mm x 35 8mm x 35...
- Page 17 * may substitute a 8 mm x 60 mm, using a 3/4 x 3/8 spacer If your Flat Screen TV is not on this list please cantact DCS Mount for updated *DCS Mount is not resposible for changes or errors in manufacturer's...