Related Manuals for Marra Forni GPZ166
Summary of Contents for Marra Forni GPZ166
- Page 1 PREP TABLES AND REFRIGERATED CABINETS Use and Maintenance ® Brick Oven Cooking Solutions...
- Page 3 INDEX GENERAL INFORMATION page MANUFACTURER SERVICE CENTRES CERTIFICATION GUARANTEE PREARRANGEMENTS OF CUSTOMER'S RESPONSIBILITY STRUCTURE OF THE MANUAL 1.6.1 AIMS AND CONTENTS 1.6.2 WHO THE MANUAL IS FOR 1.6.3 CONSERVATION 1.6.4 SYMBOLS USED DESCRIPTION AND OPERATION OF THE APPLIANCE page DESCRIPTION OPERATION PREARRANGEMENTS page...
- Page 4 GENERAL INFORMATION 1. 1 MANUFACTURER As the company boasts considerable experience in the field of industrial refrigeration. The technological know-how acquired, created during years of research and close contact with the production and marketing at an international level, represents the best guarantee that the manufacturer can offer. This equipment has been studied inside, externally and in its components, according to the requirements specified by your market.
- Page 5 • The serial number (stamped on the relevant plaque, see paragraph 4.6); • The date of purchase. 1. 5 PREARRANGEMENTS OF CUSTOMER'S RESPONSIBILITY It is the Customer's responsibility to carry out everything specified in the documentation. Unless different prior arrangements have been made, the following are usually the Customer's responsibility: •...
-
Page 6: Description And Operation Of The Appliance
DESCRIPTION AND OPERATION OF THE APPLIANCE 2. 1 DESCRIPTION The table refrigerators are condensed air refrigerator units made up of: • A condensing unit (outside cold storage room) • An evaporating unit (inside cold storage room) • A control panel (positioned on the condensing unit), ( see enclosed 13.2.3) •... -
Page 7: Electromagnetic Environment
3. 3. 1 SUPPLIES ON REQUEST It is to be understood that any modification and/or addition of accessories must be explicitly approved of and carried out by the Manufacturer. Any alteration or modification of the fridge made by the operator and/or service operator is forbidden for security reasons. -
Page 8: Danger Zone
4. 4 DANGER ZONE There are no danger zones during use because the table refrigerator has all the necessary safety devices. If repairs or maintenance have to be carried out requiring the removal of the safety devices, it is necessary first to make sure that all power sources have been switched off. For this reason in the table refrigerator it is necessary to deactivate: - The electric plant, putting the main switch off and pulling out the plug. - Page 10 4. 6 PLAQUES Plaque regarding the characteristics of the appliance PLAQUE A Example CE – PCT Example NSF - UL PLAQUE B Plaque regarding the Electrical apparatus Remove the tension before removing the protection PLAQUE C Plaque regarding the Electrical apparatus Earth symbol PLAQUE D Plaque regarding the Electrical apparatus...
-
Page 11: Please Read Carefully
Congratulations, you have just purchased the finest equipment that money can buy and you should enjoy many years of exceptional service. This product has been carefully inspected and tested to ensure its performance. When you receive this, please carefully remove the front part of the crate, the plastic liner and carefully inspect the product for damage. - Page 12 Once the equipment has been unpacked and set in place, it must be cleaned before using. Any mild spray-on cleaner can be used, such as Windex ,Formula 409 or mild soap and water. This will remove any manufacturing oils and ensure a sanitary product.
- Page 13 • Next find the left and right side splashes and make sure they are installed correctly, again by applying a bead of silicone to the bottom edge and the side. After applying silicone, position them on the countertop as shown in pic 3.
- Page 14 The controller is preprogrammed for the most efficient use of each type of table. The temperature can be programmed up or down, the defrost cycles are preprogrammed and it will display any error codes. • After 15 seconds the unit will show cooling and display the actual temperature of the cabinet and should start to drop.
- Page 15 • To change the set point from the preprogrammed 37 degrees Fahrenheit, push the menu button, use the up arrow key to get to change set, push ok, then push the up or down arrow key to the set point you want, push ok, then wait 15 seconds for the display to go back to the run mode.
- Page 16 the upper left corner will be illuminated to show the compressor is running and the unit is starting to cool. The control will also show any error codes that may occur and service should then be contacted to correct the error. The control is preprogrammed to hold at 36 degrees F and to lower or raise the temperature, push and hold the set button for 5 seconds and “machine status”...
-
Page 17: Transport And Movement
TRANSPORT AND MOVEMENT READ CAREFULLY THE WARNINGS CONTAINED IN THIS MANUAL AS THEY SUPPLY IMPORTANT INFORMATION REGARDING THE SAFETY OF INSTALLATION, USE AND MAINTENANCE. KEEP THIS MANUAL SAFE FOR FURTHER CONSULTATION. TRANSPORT AND MOVEMENT The transport and movement of the table refrigerators must take place in the upright position, respecting any indications shown on the packaging. - Page 18 6. 1 SET UP • Carefully remove the packaging from the refrigerator; • Remove the white PVC protection film from the stainless steel and all the protection used by the company to reduce the risk of damage during transport; • Place the refrigerator on a flat level surface (use the adjustable feet). (Fig. 1) Before use, clean the refrigerator with a clean, soft cloth or using a spray product.
- Page 19 • For a perfect functioning of the equipment, the maximum temperature of the environment should not exceed + 43°C (109°F). Lack of respect for these conditions will provoke a serious decline in the functioning of the equipment, early ageing of the compressor and a much higher consumption of energy than normal (Fig. 4) Fig.
-
Page 20: Putting Into Operation
In order to safeguard the electric plant of the refrigerator from any overloads or short circuits, install a magnetothermic switch at the head of the socket with adequate interruption power (See Plaque D). 6. 4. 2 HYDRAULICS If the model does not include a condenser unit, it is necessary to connect it to a drainage system for the discharge of water from defrosting using a suitable tube of appropriate dimensions. -
Page 21: Storage Of Food
It is to be remembered that: In any case, before loading the equipment, it is necessary to wait until the cold storage room have reached the correct temperature, checking it on its thermometer. If there are any brief interruptions to the electricity supply, it is probable that the compressor might start with some delay;... - Page 22 8. 1. 2 INDICATIONS ON EMERGENCY OPERATIONS IN CASE OF FIRE • Remove the plug from the socket or switch off at the mains; • Do not use water jets; • Use powder or foam extinguishers. 8. 1. 3 CLEANING OF THE EXTERNAL PARTS The following are indicated for this purpose: •...
-
Page 23: Troubleshooting
TROUBLESHOOTING The following table shows the most frequent problems, possible causes and remedies. PROBLEM DESCRIPTION POSSIBLE CAUSE SOLUTION The main switch is "off" Main switch “on” The appliance does not come on There is no tension Check plug, socket, fuse, electric connection Other Contact technical assistance The refrigerator unit does not start... -
Page 24: Technical Documentation
DEMOLITION The gas present in the plant must be extracted by authorised personnel. As far as the metal mass is concerned, it is only necessary that it be divided into steel parts and others for the purpose of recycling. ENCLOSURES 13. - Page 27 Rev 11/2020...
- Page 28 Ma r r a F o r n i 1 0 3 1 0 S o u t h a r d D r . B e l t s v i l l e MD 2 0 7 0 5 P h o n e : 8 8 8 .
Need help?
Do you have a question about the GPZ166 and is the answer not in the manual?
Questions and answers