Advertisement
Quick Links
Operating instructions
Universal Snow Plough
30266, 65061, 65062
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
Advertisement
Related Manuals for WilTec 30266
Summary of Contents for WilTec 30266
- Page 1 Operating instructions Universal Snow Plough 30266, 65061, 65062 Illustration similar, may vary depending on model Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further...
- Page 2 The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man- ual, nor in the diagrams and illustrations shown.
- Page 3 Do not operate any tools if you are tired or under the influence of alcohol, drugs, or medication. • Avoid wearing clothing or jewellery that could get caught in moving parts of the tool. Tie back long hair or cover it. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 3 http://www.wiltec.de...
- Page 4 4. Repeat this step with the other height adjuster. 5. After completing the installation, refer to the instructions for adjust- ing the height of the height adjuster in the “Operation” section. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 4 http://www.wiltec.de...
- Page 5 (45 × 12 × 4.5, 18) onto the protruding screw and tighten. Secure the assembly with an M12 locknut (4). 9. Repeat steps 7 and 8 on the other side. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 5 http://www.wiltec.de...
- Page 6 9. Firmly tighten all U-bolt nuts. 10. If the bolts extend too far down, you can cut off the excess or purchase shorter U-bolts to replace the ones included. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 6 http://www.wiltec.de...
- Page 7 6. Tighten the springs on the threaded bolts so that the blade rests against the stop screws. You may need to adjust the top nut on the threaded bolt to get the blade to fit properly. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 7 http://www.wiltec.de...
- Page 8 7. Park the ATV after use and turn off the engine. Lower the plough until it touches the ground and make sure that the cable of the cable winch is loose. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 8 http://www.wiltec.de...
- Page 9 Store the shovel if it is not going to be used for a long period of time. • Always keep it in a dry and safe place. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 9 http://www.wiltec.de...
- Page 10 Removal from storage After removing the shovel from storage, inspect it to ensure that it is in perfect condition. Parts list © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 10 http://www.wiltec.de 12 2024-1...
- Page 11 M8×20 hex bolt Important note: Reproduction and any commercial use (of parts) of this operating manual, requires a written permission of WilTec Wildanger Technik GmbH. © by WilTec Wildanger Technik GmbH Item 30266, 65061, 65062 Page 11 http://www.wiltec.de 12 2024-1...
Need help?
Do you have a question about the 30266 and is the answer not in the manual?
Questions and answers