Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Genmitsu GGW-U232
- Page 1 Genmitsu Wireless Control Module User Guide V1.2 June. 2024...
- Page 2 (Upon opening the box, please check the contents of the box against the list below. This user manual covers different models of Wi-Fi Modules so make sure to check the right list and follow the corresponding instructions.) GGW-U232 microSD U232 Wireless USB-JTAG...
- Page 3 GGW-UART microSD UART Wireless TAG-dunbot 4 PIN Dunbot SD Card Control Module Cable Cable ① ② ③ ④ 14mm GGW-JTAG microSD JTAG Wireless 10 PIN JTAG Cable SD Card Control Module ① ② ③ 22mm...
- Page 4 Install the Wi-Fi Module Prerequisites: Insert the SD card into Wi-Fi boards. Situation 1: Connect Externally Compatible Models: PRO Series: 3018-PRO, 3020-PRO MAX PROVer Series: 3018-Prover PROVerXL Series: PROVerXL 4030, PROVerXL 4030 V2, PROVerXL 6050Plus See below for how to connect the PROVer XL 6050, but the same process applies for the 4030 and 4030 V2 as well.
- Page 5 See below for how to wire the 3020 Pro Max V1, and also works on the 3018 Pro. Bottom side of UART Wireless Offline Controller Port Control Module Green Blue Black JTAG-dunbot Cable How to connect to a 3018 PROVer V1. JTAG Wireless Control Module Offline Controller Port...
- Page 6 Situation 2: Connect from Back PRO Series: 3020-PRO MAX V2, 4040-RENO, 4040-PRO (New Mainboard) PROVer Series: 3030 PROVer Max (Please note that 4040-PRO requires a new mainboard that supports Wi-Fi serial ports. Check details on our product page.) 1. Remove the case and rear plane screws and locate the 4-pin connector on the rear of the mainboard.
- Page 7 Install the Wi-Fi module on 3020-PRO MAX V2 1. Loosen the motherboard screws and locate the connector on the back of the motherboard. 2. Remove the acrylic case of the Wi-Fi Module and install the module directly on the motherboard. 3.
- Page 8 Genmitsu APP Setup STEP 1. APP Download Find in the Google app store or Apple app store by searching for Genmitsu. Download and setup. Note: Support 2.4G Wi-Fi only.
- Page 9 Network Setting For Device: Getting Genmitsu wifi modules connected to home/office wifi network Connecting to the Wi-Fi Module Open the App: Launch the mobile app for your Wi-Fi module. Access Networking Settings: Locate and tap the "Networking" button within the app. (The Left Image) Connect to Hotspot: On the following screen, tap the button labeled "Click to go to Phone Setting Panel"...
- Page 10 Wait for Connection Wait for the Wi-Fi icon from this turns to when the Wi-Fi icon turns to be like this...
- Page 11 Click back to the app that you will see the page like the left pic below, click the Network Settings button to enter the network setting page: Usually, the system will send you a pop-up prompt to ask you about keeping the connection or not during the waiting period, click “No thanks”.
- Page 12 Genmitsu Helpdoc wifi Download on the GET IT ON App Store Google Play module resource DOWNLOAD FROM THE APP STORE If you need any assistance, please contact us via: Email: support@sainsmart.com Facebook messenger: https://m.me/SainSmart Help and support is also available from our Facebook Group...
-
Page 13: Network Configuration
Network Configuration: Choose Wi-Fi Network: On the "Network Settings" page, select the desired Wi-Fi network for your device to connect to permanently. Enter Password: Input the password for the chosen Wi-Fi network. Confirm Connection: Tap the "Confirm" button to initiate the connection process. -
Page 14: Firmware Update
Firmware Update ONLINE UPDATE Wi-Fi Update Requirements: This update method is only applicable if the Wi-Fi module is already connected to a Wi-Fi router with internet access. For detailed network setup instructions, refer to the "NETWORK SETTING" section of the App Operation Guide. Update Process: Initiating the update will temporarily disconnect the device from the mobile app.After approximately 15-20 seconds,... -
Page 15: Offline Update
How to confirm the firmware on the wifi module is updated successfully? If the result shows “firmware is up to date” that means update success: OFFLINE UPDATE Requirements: • Install the latest version of the mobile app. • Connect your phone to the Wi-Fi module's hotspot. - Page 16 Update Process: Network Settings: For detailed instructions on accessing the "Network Setting" section of the app, refer to the "NETWORK SETTING FOR DEVICE" guide.
- Page 17 Offline Update: • The app will automatically check for firmware updates. • If an update is available, a confirmation popup will appear. • Click "Update Now" to begin the update process. • Upon successful completion, you will see an "Update successfully"...
- Page 18 Turning on Wi-Fi Module Lights There are two ways to turn on the Wi-Fi module's LED lights: Refer to the instructions in the app. Connect hotspot to config click light button Refer to the instructions in the app. https://genmitsu.s3.us-east-1.amazonaws.com/101-63-GGW/ Genmitsu_Wireless_Control_Module_Network_Setting_4_ MODULE_VIA_APP_20240528.mp4...
- Page 19 Connect Genmitsu APP to the Wi-Fi module https://youtu.be/UbIiLTMrcjQ Connect hotspot to config click light button...
- Page 20 IC Caution This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. To maintain compliance with RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the...
-
Page 21: Fcc Compliance Statement
FCC compliance statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 22 • Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Need help?
Do you have a question about the GGW-U232 and is the answer not in the manual?
Questions and answers
How to add custom macro to the wifi controller