iHold Music 2LP Manual

·
Insert the USB flash drive
the unit will be damaged – it may take up to 60 seconds before playback starts with USB flash drive blinking - For Adapter function see Adapter Mode page P3
·
Confirm that white LED lights in front of unit are double blinking –
·
Use one of your telephones and unplug the cord for L1/L2 from it and connect it to L1/L2 IN jack on iHold device , now
connect the L1/L2 OUT jack to your telephone using the provided cord, check for dial tone on lines 1 & 2
·
If applicable unplug the cord for L3/L4 from telephone and connect it to L3/L4 IN jack on iHold device, now connect the
L3/L4 OUT jack to your telephone using the provided cord, check for dial tone on lines 3 & 4
·
Wait till LED lights turn OFF - observe that after you connect the lines the blinking lights 1
seconds
(on non existing lines the lights keep blinking and that is OK)
·
Turn the speaker ON to confirm audio is playing and adjust the volume to mid level
Please note: just
one telephone
may be
connected to this
device, other
telephones
remain
connected to
their own wall
jacks and they all
work.
Switch set to C3: Flash activation
This setting utilizes Flash then Hold activation method
with instant activation by pressing Flash then Hold, to go back Line then Flash
Operation: make or receive a real call, the LED on the iHold turns ON solid, then simply press the
on your telephone, the Music will be heard to the caller and the LED on the iHold device starts to blink, to return to the call just re-
select the line on hold then press
the audio)
There is no voice deactivation in this setting and can not use
Switch set to C2: Flash activation
This setting utilizes Flash then Hold
by pressing Flash then Hold, to go back Line then Flash
Operation: make or receive a real call, the LED on the iHold turns ON solid, then simply press the
HOLD
button on your telephone, the Music will be heard to the caller and the LED on the iHold device starts to BLINK , to
return to the call just re-select that line and speak into the audio to stop it for example say : "Hi I am Back"
Voice deactivation may not work on some phone brands or when using VOIP lines so alternatively you may just press
stop the audio (Be sure the call has been on Hold at least 5 seconds before you try to voice deactivate or Flash to stop the
audio)
If for some reason you are not able to voice -deactivate, try speaking louder or more direct into the microphone or use the Flash
button to deactivate audio.
The FLASH button could be labeled as Call Wait or LINK or ON or TALK button on some telephones
Hold 2LP, Hold 4LP
i i
Advanced All-In-One Music On Hold device / Adapter
Rev 66
1 then connect the included AC adapter
st
(or SD card)
110 - 240 V
Prog
Not used
A B C 1 2 3
Speaker
ON OFF OFF
L1 L2
Min Volume Max
C
(Be sure the call has been on Hold at least 5 seconds before you use Flash to stop
FLASH
1 2 3
C
activation method, this setting supports any phone or any mix of brands with instant activation
In setting 2 lower the volume level to avoid audio flickering on Hold
for regular phones continue,
Audio
Output to
PBX
L3/L4
OUT
SD card slot
USB drive
1 2 3
This is the Recommended setting -
switch change
this setting supports any phone or any mix of brands
(with no voice de activation)
in case you have "call waiting" service
FLASH FLASH
You must hang up 1st to make a switch change
(110- 240 V AC to 5V DC) do not to use a different power adapter or
for PBX phones go to page P4
stops then turns OFF after 20
st
(you can Turn it OFF any time)
L3/L4 L1/L2 L1/L2
IN OUT IN
NXT L3
Not used
LED
must hang up 1st to make a
FLASH
FLASH
Not used
Back
L4
Front
HOLD
then button
then
to
FLASH
P1