Advertisement
Advertisement
Table of Contents
Summary of Contents for TS Enovations IMD3
- Page 1 PRODUCT SPECIFICATION AND MANUAL IMD3 MANUAL INSUL ATION MONITORING DE VICE...
-
Page 2: Table Of Contents
Users need to have insight in the dangers of operating this device. • Electrical devices are no toys. Therefore, store and use this device out of reach of children. 2 | IMD3... - Page 3 WARNING! supply available. If the IMD3 not work properly or the housing is damage, shut off the installation and go to a • Be aware other devices do not cause a short circuit at the contacts of the device. certified company and let the system inspected to ensure the security of the system, or send •...
-
Page 4: General Description
Under normal circumstances where 230Vac is Isolation failure The IMD3 has been designed for installations present in the MAINS, the IMD3 does not register MAINS with correct earthing: where 230Vac is being generated by inverters. an ‘Isolation failure’ . This is due to the inverter... -
Page 5: Installation
PE-Pipe or connected directly with the Remote and the IMD3 Remote contacts. vehicle’s chassis. Position the IMD3 in a closed off area, which • When Connected to a an external 230Vac grid can only be carried out by qualified and make sure this grid is properly grounded and authorised personnel. - Page 6 10 | IMD3...
- Page 7 12 | IMD3...
- Page 8 • Select: Do not use VS (Virtual Switch) - Select: Start assistant and follow instructions • Select: Start assistant and follow instructions - Select Tab: Assistants - Select: Add Assistant - Select: safety switch - Select: Start assistant and follow instructions 14 | IMD3...
- Page 9 • Select: >> • Select: Send settings - Select: Send settings • Select: All settings - Select: All settings - Window: Input - Select: Switch the unit off when: temperature sense input is opened - Select: >> 16 | IMD3...
-
Page 10: Floating Circuit
In Victron VE.Config: Tab Inverter -> Clear the selection of the ‘ground relay’ checkbox. Diagram 5 If everything is connected correctly and the ground relay is disabled, you can test whether the isolation guard activates after switching on your inverter. 18 | IMD3... - Page 11 125 °C RTI IMP UL 746B 1.5 mm 105 °C 2.5 to 2.8 mm 105 °C 3.0 mm 105 °C RTI Str UL 746B 1.5 mm 125 °C 2.5 to 2.8 mm 125 °C 3.0 mm 125 °C 20 | IMD3...
- Page 12 Sub gate Cold 230x250x300 PC/ABS (FR3010) SrewCover_TopBottom_ runner 2021118 GroundInsulation_DinAssembly 31.9x28.5x5.5 NAK80 500k shots Sub gate Cold 200x270x280 PC/ABS (FR3010) Plastic_20211203 runner GroundInsulation_Transparant 53.43.3x6 S136H 500k shots Open gate Cold 250x250x280 (PC-110) Cover_20211118 runner Polycarbonate V2 transparent 22 | IMD3...
-
Page 13: Technical Specifications
Earth fault active Vin-0.45 aggressive detergents Iout2 trip current (PPTC Vin max = 60V Use in parallel The IMD3 can’t be use resettable fuse) in parallel or with other Iout2 hold current (PPTC Vin max = 60V insulation monitors resettable fuse) - Page 14 Emission EN 61000-3-3 (2013) +A1 (2019) + A2 (2021) + AC (2022) (not yet harmonized) Emission / Immunity EN 61326-2-4 (2013) Electrical Safety IEC 61557-1 IEC 61557-8 IEC 61010-1 IEC 61010-2-030 The EMC reports can be downloaded on our website. 26 | IMD3...
- Page 15 Lemsteraak 6 • 2411 NC Bodegraven • The Netherlands Tel. 0031 (0)172 - 650 737 info@ts-enovations.com www.ts-enovations.com...
Need help?
Do you have a question about the IMD3 and is the answer not in the manual?
Questions and answers