Related Manuals for Neware MHW-200
Summary of Contents for Neware MHW-200
- Page 1 Neware Constant Temperature Chamber-MHW-200 User Manual issac@newarelab.com Neware Technology Limited www.newarelab.com...
- Page 2 Please read carefully. Liabilities Neware is not responsible for the damage that results from negligence or fault operations that are not caused by Neware. Please follow this "user manual" to avoid potential negligence or fault. Attention Keep the manual. Ask for a replacement if any errors in this manual are found.
-
Page 3: Table Of Contents
3.3 Others ..................... 8 Chapter 4 Chamber information ................8 4.1 Specification ....................8 4.2 Appearance ...................13 4.3 Setting on control panel ................14 4.4 Control chamber’s temperature in Neware BTS 8.0 Client ....15 4.4 Operation on BTS 8.0 Client ..............16 issac@newarelab.com Neware Technology Limited www.newarelab.com... - Page 4 Installation Warning Operator must read this user manual before installation. Read this chapter if you need to move the equipment. Users must read this chapter no matter whoever is responsible for installation. issac@newarelab.com Neware Technology Limited www.newarelab.com...
-
Page 5: Chapter 1 Accessories Checked
• Humidity: ≤85%RH No high-density dust, no flammable or corrosive components around the • equipment ； • Closer to Neware tester. warning Work environment: 5℃～35℃ ■ Storage/Operating space This equipment is designed for in-door usage. Equipment is required to be set up on a flat concrete floor or on a setting plate that can support the weight of the equipment. -
Page 6: Power Supply
Users are required to set up the air switch or power switch with related capacity, and these switches must independently operate for this equipment. warning The power supply voltage can not exceed ±10% of the nominal voltage, otherwise, chamber will be alarmed. issac@newarelab.com Neware Technology Limited www.newarelab.com... - Page 7 The device's external power sources are not permitted to be paired with power sockets or knife switches.。 Warning Please make sure resistance to ground ≤10Ω, if there is no ground connection terminal in power supply. issac@newarelab.com Neware Technology Limited www.newarelab.com...
- Page 8 ■ Power line connection User chamber’s power line connect to power supply. Warning Screw the power line tightly. Do not turn on the power of chamber when you open power supply or under maintenance! issac@newarelab.com Neware Technology Limited www.newarelab.com...
-
Page 9: Operation
Operation Attention If you are the first time user, please read the manual from Chapter 3. If you are the experienced user, please also read ‘Safety Precautions’ in chapter 3 carefully. issac@newarelab.com Neware Technology Limited www.newarelab.com... -
Page 10: Chapter 3 Safety Notice
Anything that can produce above substance or material 3.2 Sample Protection Device warning According to the test, to set the protection device, If not set up properly , the accidents in the test may damage the sample issac@newarelab.com Neware Technology Limited www.newarelab.com... -
Page 11: Others
Turn off main power supply before maintenance. Start to test after all installation done. Chapter 4 Chamber information 4.1 Specification MHW-200 Constant Temperature Testing Chamber Model:MHW-200 Material Code: MHW-200 Description Product Specification AC Input AC 220V±10% 50Hz Single Phase+protective earth ground Power Input Current Volume、Size... - Page 12 The controller will be followed the given temperature, then automatic calculate and export the result, so that can control the actual value, to reach the dynamic condition. Communication Ethernet port mode Temperature controller Independent R&D by Neware module Connecting with Neware battery system issac@newarelab.com Neware Technology Limited www.newarelab.com...
- Page 13 Hardware With RS485 port Connection Diagram Software issac@newarelab.com Neware Technology Limited www.newarelab.com...
- Page 14 Picture for reference, please confirm the actual product issac@newarelab.com Neware Technology Limited www.newarelab.com...
- Page 15 Neware Technology Limited www.newarelab.com...
-
Page 16: Appearance
Air circulation Connection Hole Testing cable connect inside battery through this hole Air Intake Ventilation and heat dispersion The door of cooling Maintenance component TCP port Connection with control unit Power line port Connection power line issac@newarelab.com Neware Technology Limited www.newarelab.com... -
Page 17: Setting On Control Panel
4.3 Setting on control panel ① Start/ Stop (Holding button for 5 seconds to stop running and enter into standby mode; After set temperature, press button to start. ) ② Infrared Sensor ③ Real temperature value display issac@newarelab.com Neware Technology Limited www.newarelab.com... -
Page 18: Control Chamber's Temperature In Neware Bts 8.0 Client
⑫ Down ⑬ Back ⑭ Confirm(Under unlock state, press button to enter configuration interface) 4.4 Control chamber’s temperature in Neware BTS 8.0 Client Input “LP” address on your browser: Neware/xinwei Find Autoline configure, choose “M2WX64”, and input “LP” address and port number in red box. -
Page 19: Operation On Bts 8.0 Client
Submit it. 4.4 Operation on BTS 8.0 Client Open BTS8.0 Client. After login(admin/neware), right click on the right area, to choose “Rest mapping”. Right click to choose “Main CH default mapping” is “1x8”, and “Aux-CH default mapping” is “average mapping”. Then right click again to save mapping. - Page 20 In “Start test” interface, use “Control” step, set temperature value. issac@newarelab.com Neware Technology Limited www.newarelab.com...
- Page 21 If you have any questions, please do not hesitate contact us! Support: Issac Zhu Phone: +86-18576651064 Mail: issac@newarelab.com issac@newarelab.com Neware Technology Limited www.newarelab.com...
Need help?
Do you have a question about the MHW-200 and is the answer not in the manual?
Questions and answers