Related Manuals for Knuth B 200 S
Summary of Contents for Knuth B 200 S
- Page 1 Machine Tools OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS B 200 S Part No 102752 For the important safety of your body, please read this manual book and understand its contents before operation.
- Page 2 Machine Tools OPERATING INSTRUCTIONS 1 Safety instruction Operation manual For your own security read the operation manual before starting the machine. The operation manual should be kept in a secure place. You should know about how to handle the machine, it’s limits and it’s specific dangers. Keep your working place clean Disorder on your working place will result in danger.
- Page 3 Machine Tools OPERATING INSTRUCTIONS Unplug the machine If you don’t use and while servicing the machine pull off the power supply plug. This is necessary because the machine should not run unintentionally and to protect you from electric shock. Beware of unintentional run Confirm that the main power switch is off while you plug in the power supply plug.
-
Page 4: Safety Rules For All Tools
Machine Tools OPERATING INSTRUCTIONS 1. WARNONG: FAILURE TO FPLLOW THESE RULES MAY RESULT I SERIOUS PERSONAL INJURY As with all machinery there are certain hazards involved with Operation and use of the machine. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the Operator may result. -
Page 5: Maintenance
Machine Tools OPERATING INSTRUCTIONS Don't use power tools in damp or wet locations, or expose Cast, low cutting rate and permanent blade failure. Dirty them to rain. Keep work area well-lighted. (3). KEEP coolant can cause the growth of bacteria with ensuing CHILDREN AND VISITORS AWAY. - Page 6 Machine Tools OPERATING INSTRUCTIONS 4. TRANSPORTATION OF MACHINE: Unpacking 1. Transportation to desired location betöre unpacking, please use lifting jack. (Fig. B) 2. Transportation after unpacking, please use heavy-duty fiber belt to lift up the machine. ALWAYS KEEP PROPER FOOTING & BALANCE WHILE MOVING THIS MACHINE. 5.
- Page 7 Machine Tools OPERATING INSTRUCTIONS...
-
Page 8: Make Proper Tooth Selection
Machine Tools OPERATING INSTRUCTIONS recommendations presented on this chart are 7. MAKE PROPER TOOTH SELECTION approximations and are to be used as a starting For maximum cutting efficiency and lowest cost per cut, it is important to select the blade with the right point for most approximations. -
Page 9: Work Stop Adjustment
Machine Tools OPERATING INSTRUCTIONS CHANGING BLADE SPEED (1). Disconnect machine from the power source. (2). Loose motor plate lock bolt (1, Fig.5). (3). Loose motor plate slide bolt (2) until belt can be moved on the pulleys. (4). Move belt to the desired pulley combination. (5). -
Page 10: Coolant Tank Preparation
Machine Tools OPERATING INSTRUCTIONS E. COOLANT TANK PREPARATION toward the motor as follows: (1). Place the blade in between each of the guide AWARNING bearings. Disconnect and saw from the power source (2). Slip the blade around the motor bebre making any repairs or adjustments! pulley Failure to comply may cause serious injury! (bottom) with the left hand and hold inposition. - Page 11 Machine Tools OPERATING INSTRUCTIONS TRU-LOCK VISE SYSTEM INSTRUCTIONS To operate, proceed as follows: (1). Rise the arm 2" above the workpiece, dose the cylinder valve to maintain the arm 2" above the workpiece. (2). Put your workpiece on the table. Move the vise handle (a) upwards to an angle of 45 degree (a-half opened) to loosen the vise.
- Page 12 Machine Tools OPERATING INSTRUCTIONS the saw is used properly, if the guides do get out REMARK: of adjustment though, it is extremely important to (1). Adjust the tension of blade until the back of readjust immediately. If improper adjustment in the blade (A) against the blade wheel (front) maintained, the blade will not cut straight, and if lightly.
- Page 13 Machine Tools OPERATING INSTRUCTIONS The blade is tracking properly when the back side over-heating or stränge noise, stop just touches the Shoulder of pulley or a slight gap machine appears near the center line of the pulley. Care immediately to cheek it for keeping accurate should be taken not to over-tighten the saw blade Performance.
-
Page 14: Tr0Uble Shooting
Machine Tools OPERATING INSTRUCTIONS 14.TR0UBLE SHOOTING Symptom Possible Cause(s) Corrective Action Excessive Blade I.Materials loosen in vise 1 .Clamp work securely Breakage 2.lncorrect speed orfeed 2.Adjust speed or feed 3. Blade teeth spacing too large 3.Replace with a small teeth spacing blade 4. - Page 15 Machine Tools OPERATING INSTRUCTIONS Bad Cuts (crooked) 1 .Feed pressure too great 1. Reduce pressure by increasing spring tension on side of saw 2.Guide bearings not adjusted 2. Adjust guide bearing, the clearance can properly not greater than 0.001 3.lnadequate blade tension 3.
-
Page 16: Circuit Diagram
Machine Tools OPERATING INSTRUCTIONS 15.CIRCUIT DIAGRAM Grounding: The grounding of this model is carried out by connecting the yellow/green terminal of supply cable to the grounding terminal of power source. Be sure to ground your machine before connecting machine to power source in any Situation. - Page 17 Machine Tools OPERATING INSTRUCTIONS...
- Page 18 Machine Tools OPERATING INSTRUCTIONS...
- Page 19 Machine Tools OPERATING INSTRUCTIONS...
- Page 20 Machine Tools OPERATING INSTRUCTIONS...
- Page 21 Machine Tools OPERATING INSTRUCTIONS...
- Page 22 Machine Tools OPERATING INSTRUCTIONS...
- Page 23 Machine Tools OPERATING INSTRUCTIONS...
- Page 24 Machine Tools OPERATING INSTRUCTIONS...
- Page 25 Machine Tools OPERATING INSTRUCTIONS...
- Page 26 Machine Tools OPERATING INSTRUCTIONS...
- Page 27 (for KNUTH only) You would assist us grately in this matter. Yours sincerely, KNUTH Werkzeugmaschinen GmbH KNUTH - Customer-No. ____________________________________ Company __________________________________________________________________________ Adress __________________________________________________________________________ __________________________________________________________________________ Your personally name __________________________________________________________________________ Phone-No.
Need help?
Do you have a question about the B 200 S and is the answer not in the manual?
Questions and answers