Defro SMART II Operating Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

DEFRO SMART II

V3.5

Software version: 1.1.20.0

Operating manual

Kutno

2016-10-07

Table of Contents

Need help?

Do you have a question about the SMART II and is the answer not in the manual?

Questions and answers

Summary of Contents for Defro SMART II

Page 1 DEFRO SMART II V3.5 Software version: 1.1.20.0 Operating manual Kutno 2016-10-07...
Page 2: Table Of Contents
Table of Contents 1. Safety ..............................3 2. Assembly ............................5 2.1 Environmental conditions ....................... 5 2.2 Control panel setup ......................... 5 2.3 Connecting the sensors ......................6 2.4 Sensor of breaking a split pin ....................8 2.5 Sensor of closing the storage unit ................... 8 2.6 Connecting the 230V AC automation devices ................
Page 3: Safety
Technical data Power supply............230V~50Hz Protection degree..........IP40 Electrical protection class.....I Acceptable ambient temperature range..from 5°to 45°C without condensation Feeder line load......to 1 A Blower line load......to 0.8 A Each line pump load......to 0.5 A Valve line load......to 0.2 A Fuses ..........4 A 1.
Page 4 pin, because of safety reasons and electromagnetic interferences which can influence the operation of controller and devices working with it. • Do not expose the controller to excessive humidity causing condensation (e.g. in rapid external temperature changes) and avoid spilling water on •...
Page 5: Assembly
2. Assembly Assembly and installation works should be carried out by an authorized service or suitably qualified specialists, in accordance with the applicable regulations and standards. 2.1 Environmental conditions Do not expose the controller to excessive humidity causing condensation (e.g. in rapid external temperature changes) and avoid spilling water on it. Do not expose the controller to temperatures higher than 45ºC and lower than 5ºC.
Page 6: Connecting The Sensors
2.3 Connecting the sensors Activation of the devices connected and the controller functions is automatic and depends only on connecting the temperature sensors to the controller. For example: connecting a domestic hot water (DHW) temperature sensor activates the pump, and connecting a sensor of external temperature makes it automatically possible to use weather compensator, and so on.
Page 7 Picture 2: Terminal strip for connecting the sensors 7/40...
Page 8: Sensor Of Breaking A Split Pin
2.4 Sensor of breaking a split pin Split pin breaking sensor should be connected as shown on the picture 3. The sensor helps to diagnose problems with the operation of the feeder. Picture 3: Connecting the sensors of split pin breaking and of closing the storage unit. 2.5 Sensor of closing the storage unit Here we can connect Storage unit closing sensor –...
Page 9: Operation Of The Controller
• Mixing , circulation or boiler feed pump Follow the instructions given on the casing. 3. Operation of the controller 3.1 Operator panel The LCD operator panel is equipped with a OLED graphic display, six buttons and pictograms with LEDS signalizing the operation of the following equipment: •...
Page 10: Operator Panel - Operation Level
3.2 Operator panel - operation level In case of incorrect communication between the panel and the controller a message: "No communication, check the controller connection" will be displayed. 3.2.1 Home screens The following information is displayed on the home screen right after activating the controller: First screen: Type and model of the display...
Page 11 Picture 5: Controller type and software version The next start window informs about the selected type of the boiler. Picture 6: An example of the boiler type At the first start of the controller and after restoring the factory settings there will also be displayed a screen on which a suitable boiler type should be selected.
Page 12: Main Screen
• change the boiler type • choice confirmation Table 2: The functions of the buttons on the Boiler type selection screen 3.2.2 Main screen The following information is available on the main screen: measured and set temperatures of the boiler •...
Page 13: Dhw Screen
• navigate the information screens • go to setting the boiler temperature • go to setting the boiler reduced temperature • go to the controller settings - pressing for 2s Table 4: Functions of the buttons on the main screen 3.2.3 DHW screen Picture 9: DHW operation screen circulation pump operation...
Page 14: Feeder Screen
• go to setting the DHW mode • go to the controller settings - pressing for 2s • return to the main menu Table 6: Functions of the buttons on the DHW screen DHW operating modes: • Zal – DHW active (ON) •...
Page 15: 1 And Ch.2 Circuits Screen
The controller makes it possible to generate entries to the events archive about new fuel batch fed to the storage unit and a notification of low level of fuel in the storage unit. Feeder working time is used to deduct it. 3.2.5 CH.1 and CH.2 circuits screen Screens are available depending on the type of CH (central heating) circuit chosen.
Page 16: Network Screen
active room thermostat • circuit type - central heating (CH) or floor heating • valve operating mode (only for the CH.1 circuit) • Table 9: Symbols on the CH.1 and CH.2 circuits screen 3.2.6 Network screen The following information is available on the network screen: state of network cable connection •...
Page 17: Alarm Screen
3.2.7 Alarm screen The screen lists current alarms. Picture 14: Alarm screen navigate the information screens • alarm review • confirmation of all alarms • return to the main menu • each button mutes audible alarms • Table 10: Functions of the buttons on the alarm screen An additional device for signaling a controller alert (e.g.
Page 18: Manual Control Screen
3.2.8 Manual control screen Picture 16: Manual control screen • navigate the information screens • selection of a device • turning the device on/off • setting to blower and pressing the button for 2s allows to change Blower power in manual mode. •...
Page 19: Controller Parameters
Picture 18: Controller menu plan 4. Controller parameters 4.1 Combustion parameters Parameter Description Retort-AUTO retort feeder, fully automatic combustion process. Retort-group retort feeder, semi-automatic combustion process. Retort-manual retort feeder, combustion process fully set by the operator. Top-loading option of an on-grate combustion with a stopped feeder. 19/40...
Page 20: Combustion Parameters - Retort - Auto Type
4.1.1 Combustion parameters – Retort - auto type Combustion process is fully automatic. Combustion parameters are chosen automatically without any service or operation. No. Parameter Description Setting the output parameters of the combustion algorithm for Boiler type a particular boiler type. This parameter does not change the algorithm.
Page 21: Combustion Parameters - Retort - Manual Type
Range [25% to 100%] Number of repetitions for Defined number of feedings in the group for 16kW Range [3 to 6] 16kW Blower power for 20kW Blower power for 20kW Range [25% to 100%] Number of repetitions for Defined number of feedings in the group for 20kW Range [3 to 6] 20kW Blower power for 25kW...
Page 22: Combustion Parameters - Top-Loading Type
Boiler temperature hysteresis. Temperature above the set value for the boiler – the Uphold mode is engaged; temperature below Boiler hysteresis the set value minus Hysteresis of the boiler – going into the Heating mode. Range [0°C to 5°C] 4.1.4 Combustion parameters – top-loading type The mode of on-grate combustion with a stopped feeder.
Page 23: Blower Power In Manual Mode
No. Parameter Description Uphold: Feeder working Fuel feeding time in the Uphold mode. Range [3s to 30s] time Uphold: Feeder standstill The standstill time in the Uphold mode. Range [3min to 360min] time The short break time (standstill) of the feeder in the Uphold mode.
Page 24: 1 Circuit
boiler outlet for each weekday. programmer Programming the reduced temperature has also an impact on the work of the weather compensator. Activating the weather compensator. The compensator deducts an adequate temperature set for the boiler, based on outdoor temperature and a heating curve. Connecting wired or remote Weather compensator temperature sensors BT2 is a prerequisite for this function.
Page 25 floor heating manifolds. It provides heat management at home via our website mobile application. find more information http://sklep.esterownik.pl/. When using a 4-way valve, the valve sensor should be connected to the T1 sensor input - see Picture 19. Picture 19: Connecting valve actuator and internal sensors for the CH.1 circuit An external thermostat can be connected to the controller.
Page 26 programmer. Connecting wired or remote humidity and temperature sensors BT1 is a prerequisite for this function. Ability to use external thermostat. ● CH pump + 4D - P1 pump and 4-way valve ● CH pump + 4D + room regulator - P1 pump working with 4-way valve based on the inside temperature coming from the programmer.
Page 27: 2 Circuit Screen
Temperature set Water temperature set behind the valve. 10.1 behind the valve Range [20°C to 80°C] Temperature The value by which the set temperature behind the valve will be 10.2 reduced behind the reduced when there is set a reduced temperature in a programmer. valve Range [0°C to 25°C] Reaching this temperature results in generating the alarm: High...
Page 28: Dhw Circuit
information on http://sklep.esterownik.pl/. An external thermostat can be connected to the controller. The thermostat should be connected to the T2 (internal temperature) contacts of the controller board (in the place of an internal sensor). The thermostat is required to have an potential-free contact.
Page 29: Programmers
Pump standstill time for the cyclic mode. 7.3 Pump standstill time Range [1min to 240min] The prerequisite for starting the circulating pump - minimum Temperature of temperature in the DHW storage unit. Hysteresis for turning off starting the circulation 0.5°C pump operation Range [25°C to 60°C] 4.6 Programmers...
Page 30 confirm the selection and go to the programmer • return • Table 13: The functions of the buttons for the weekday selection screen for the programmer Programmer operation Picture 21: Boiler programmer screen time selection / programmer overview • action/task selection •...
Page 31: Internet
Programmers Operation Description Frost protection 7°C Low temperature Room programmer for the CH.1 and CH.2 circuit Normal temperature Comfortable temperature Pump turned off Circulation pump Pump activated programmer Cyclical work of the pump Winter mode Auto-Summer Summer mode programmer Auto-Summer mode 4.7 Internet Options allowing to set parameters which make it possible to connect the controller by means of the Ethernet.
Page 32: Date And Time
• NO - setting the IP address manually IP Address The IP address of the controller which is seen in the local network Mask Network mask Gate Default gate Restoring the default settings of the Ethernet and resetting the Default settings of the login passwords of the local website.
Page 33 Parameter Description process Retort Group – retort feeder, semi-automatic combustion • process Retort Manual – retort feeder, combustion process fully set • by the operator Top-loaded – option of an on-grate combustion • Detection of boiler damping down in the Uphold and Heating mode, based on the exhaust temperature: Inactive –...
Page 34 Parameter Description Range [1min to 10min] Split pin breaking Activating the function of feeder damage detection Range [YES/NO] sensor Sensor of closing the Activating the function of open storage unit detection Range [YES/NO] storage unit Delay time of closing The time after which an Open feeder alarm will be reported Range [0s to 60s] the storage unit The time of feeder operation after which the storage unit will be...
Page 35: Alarms
5. Alarms An alarm is signaled by a red LED light on the control panel and an audible signal (which is stopped by pressing any button on the panel – it does not mean cancelling the alarm). Turning off and restarting the controller supply confirms alarms as well - only if the cause was removed.
Page 36 The name of the Automatic Description alarm stopping alarm The boiler was put out - the alarm relates to the Uphold and Heating mode. When: - in the Heating mode - the exhaust temperature does not exceed 50°C in 30min. Check if the boiler Boiler put out exchanger and the flue are clean.
Page 37 The name of the Automatic Description alarm stopping alarm Only for floor heating: Maximum temperature High temperature behind the 4-way valve has been exceeded. The behind the 4-way valve valve can be closed for floor heating. 37/40...
Page 38: Declaration Of Conformity
Declaration of conformity ELEKTRO SYSTEM Plus Sp. Z o.o. with its official seat at ul. Rychtelskiego 5 in Kutno hereby declares that the product: Adaptive controller DEFRO SMART II V3.5 complies with the provisions of the following European Directives: •...
Page 39 WARRANTY CARD Name of the device Adaptive controller DEFRO SMART II V3.5 Production date Recipient Invoice number Date of sale Terms and conditions: ELEKTRO SYSTEM Plus Sp. Z o.o., hereinafter referred to as the Guarantor, ensures a good quality and efficient operation of the purchased equipment, when used in accordance with its intended purpose and this manual.
Page 40 Elektro System Plus Sp. z o.o. ul. Rychtelskiego 5 99-300 Kutno Tel: +48 24 253 76 63 Tel: +48 24 355 05 63 Mob: +48 574 443 555 Fax: +48 24 355 05 73 www.eSterownik.pl serwis@elektro-system.com 40/40...