1. Manuals
  2. Brands
  3. jWIN Manuals
  4. DVR
  5. JD-VR70
  6. Operation manual

jWIN JD-VR70 Operation Manual

Jwin jd-vr70: software guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
jWINSheriff
V4.2
Operation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JD-VR70 and is the answer not in the manual?

Questions and answers

Summary of Contents for jWIN JD-VR70

  • Page 1 jWINSheriff V4.2 Operation Manual...
  • Page 2 Introductio n...

  • Page 3: System Requirements

    System Feature jWINSheriff V4.2 provides advanced digital technology that supercedes old-fashioned CCTV monitoring and VCR systems. It allows 'instant replay' and simultaneous recording. jWINSheriff V4.2 also provides security personnel to define 'security events' that require recording compression of non-event periods into a few frames of video for continuity.
  • Page 4 jWINSheriff Installing Board 1) Turn off power on the computer. * It is very important to turn the computer’s power before you open the case. Static Electricity can provide a big enough shock to damage the components of your PC. NEED EXPLAIN ABOUT PROPER...

  • Page 5: Install System

    Install System Video Out A User may connect CCTV camera, video phone, or video out port of any security system to one of camera input ports on GVC capture card. Also, a user may use TV out to connect an external analog CCTV monitor.

  • Page 6: Install Software

    Install Software jWINSheriff 1) After installed Board, and turn on your computer, automatically display as below “Found New Hardware Wizard” program. At that time, click all of “Cancel” button, and finished Wizard program. (according to a type of board and quantity of board, can be repeated.) jWINSheriff 2) To install...
  • Page 7 4) Select "Install Recorder". 5) Before installation takes place, a dialog box will ask whether it should install with driver. jWINSheriff If you selected “Yes”, it will install the program with driver (The Driver is jWINSheriff needed to run this program. If this is your first installation of on your Computer, you must select “Yes”) 6) And then Installing device driver.

  • Page 8: Main Screen Overview

    Main Screen Overview Minimize/ Close Screen Mode Channel Rotation Control Speed Control Extension Video & Audio Recording Setup Local Viewer Status Warning Power Digital Out Local Viewer: Run Local Viewer[Search] Setup : Run Setup Minimize/Close : Hide Button DVR Recorder in tray bar, and Close Button[Exit] Video &...
  • Page 9 SETUP...
  • Page 10 Preset ID and Password The preset ID is set in “Administrator,” Password is set in “Admin.” Setup Tree General - Display Device - Video Input Signal - Communication Setup(WebCam Server) - PTZ Setup - Save Image Quality - Font - Use Full screen mode - Check Daily Reboot - Use Password - User Add/Delete...

  • Page 11: Display Device

    Display Device jWINSheriff Basically, support DirectX, but the graphic card of your computer sometimes do not support above DirectX and YUV Overlay. In this case, you must set up “Display Device” to “RGB Device” (The default value is “RGB Device”.) Video Input Signal jWINSheriff support both of Video signal NTSC and PAL type.

  • Page 12: Setup The Communication

    Setup the communication 1) Using TCP/IP - Check “Use TCP/IP” in Check box.
  • Page 13 2) Using Dynamic IP by DHCP of ADSL, Cable modem. - First, verify the network connection and Internet connection is working. - Check “Use TCP/IP” in Check box. - Click “Web registration.” - Click “Register Web server” -> Pop-up window will appear. - Key in “www.inetdvr.com”...
  • Page 14 4) Using Serial Device - Check “Use Serial Device” in check box. - Set up communication port and transfer rate.

  • Page 15: Webcam Server

    5) Using PSTN (Public Subscriber Telephone Network) Dialup Modem. - Check “Use serial device” in check box. - Check “In Modem device.” - Click “Find Modem” or set up communication port. - Set up “Baud rate” WebCam Server 1) Using a WebCam Server Even if you have no client program at the remote site you can watch images to using a web browser.
  • Page 16 The value of default port is 80, but the user can change the value of the default port. If there is no display of the image due to the firewall. (The remote user can connect the webcam server to the recorder without the network administrator authorization. Note: For broadband T1 and Dial up Connection The user sets up the frame rate according to the communication speed of the on line...
  • Page 17 PTZ (Pan Tilt Zoom) Set up communication port for control PTZ, transfer rate, parity. The PTZ Receiver uses RS-485 communication protocol, and you can reserve that port for DVR capture board. “COM1” or “COM2”, can only be used for (RS-232C) protocol. jWINSheriff supports setting each PTZ Receiver by different ID number (in tab “Set up Camera”)

  • Page 18: Full Screen Mode

    Font Set up User can change font of camera name. Full Screen Mode If there is no keyboard or mouse movement within a 60 second period the screen will automatically be changed to the full screen mode. Daily Reboot Feature When the daily reboot function is checked, the system will automatically reboot itself at the prescribed time.
  • Page 19 User Add/Del To register new user, click “User Add/Del” button, and then click “Add new user”. Insert new ID and Password about new user. In user authority, “allow multiple Access” have the function that multi user can do simultaneous access. However, supervisor is not permitted multiple accesses (Person that have authority of run/end, set up it.)
  • Page 20 Window Shell Mode If you wanted to use your computer for DVR, Check this box. If you checked this, after computer rebooting, Only DVR runs on your computer without any application. Site Name This system window with “Site Name” to distinguish another DVR’s from remote client Program.
  • Page 21 Sensor/Alarm This section defines the sensor/alarm action. jWINSheriff supports 2 type of Sensor/alarm action. “x”: If sensor works, record those images according to schedule. From above “x,” click right mouse, you can use extension functions (Preset, Light On, User Operation). When PTZ was supported, “P1 ~ P16”: When sensor works, camera operates to preset location.
  • Page 22 You can set NC (Normal Close), NO (Normal Open) and Alarm out duration. Digital out is worked by event on schedule, during how long time you set. It’s not worked when you switched digital out. For setup alarm out duration For setup NC, NO Click D/O channel number Click Sensor number...
  • Page 23 Set up camera connection and resolution jWINSheriff program can identify camera signal automatically though the camera connected. When you do not see images (because of camera broken, disconnection of a cable), ”Video loss” will occur at local or remote monitoring center. The recording resolution is supported by 320X240, 640X240, 640X480 on NTSC, 384*288, 768*288, jWINSheriff 768*576 on PAL.

  • Page 24: Camera/Motion Detection

    Camera/Motion Detection To set up the Motion detection area, click and drag the left mouse button. To cancel the area, click and drag the right mouse button. Clicking on the “Detection sensitivity” button, you can control the sensitivity of Motion Detection. Also if you couldn’t notify Motion detection area very well, you can change the color of Motion detection area to other color by clicking “Change detecting point”...
  • Page 25 Set up overlay (Advanced Model) If you use Overlay board (GVC-16R), you must set up brightness, color, etc. of Overlay board in addition...
  • Page 26 Set up types of PTZ Receiver You can set up different types PTZ receivers.

  • Page 27: Set Up Audio

    Set up Audio This function is a part that set voice sensitivity compounding camera. User can set up camera and audio environment to use audio. Click camera #1 button Setting audio, Icon of speaker shaped come out in lower column part. “Audio setting”: Lower button is better quality, but file size is getting bigger and bigger.

  • Page 28: Recording Schedule Set Up

    Recording schedule set up If you wanted to compound schedule with “Audio(A)”,“Sensor(S),” “Motion detection (M)”, “ON-time (T), after clicked one of those buttons and drag with push on left mouse button. If you want to record Audio, audio is set up on schedule. ※...
  • Page 29 Holiday Registration You can program holidays, to record or not to record on the registered holiday.
  • Page 30 Motion Record Set up(Each Camera) To activate “Alarm in Detection” and “Sensor in Detection,” click on the check box marked ALARM IN DETECTION. The post alarm recording may be adjusted from 0 to 60 seconds by sliding the bar forward or backwards. This will allow recording to continue after motion has stopped. PreAlarm Recording Setup(Each Camera) You can set the Pre Alarm Recording time from 0 to 10 seconds.
  • Page 31 Set up storage space Following the initial installation of the software you must set up your disk storage space allocation. This allocation of storage space is user defined and can be allocated in several different hard discs. Storage space is displayed in 3 types. Application space : Space that installed OS, DVR Program and some Application program.
  • Page 32 Using Line Monitor You can connect an additional monitor to view the camera activity using the TV OUT RCA connection on DVR board. Select the line monitor function to display the desired camera output. The images then be displayed in full screen by rotation. ※...
  • Page 33 Using Alert Mode When sensor input is triggered, or detects motion from server system with registration of pre-designated client communication address, the detected data information is transmitted with alarm to predestinated remote multi viewer when connecting in a network. Auto Release Alert Event To automatically release an alert event, check the Auto Release Alert box.
  • Page 34 Notify E-mail As detecting sensor, motion set in alert mode, Final image of camera and log data detected is informed to assigned E-mail address . (For example: “dvr@dvr.com;bbb@dvr.com.net;mailccc@dvr.com”)

  • Page 35: Local Viewer

    Local Viewer (Search)

  • Page 36: Screen Overview

    Screen Overview Backup Save Print Backup Motion detect play Viewer Event List Screen Division Multi-Speed play Recording Zoom Ctrl Status Brightness Motion Recording Recording Backlight Sensitivity Date & Time Date & Time Exit Play Control jWINSheriff It’s displayed when ’ setup is for NTSC. [General tab in Setup See pg.11]...
  • Page 37 jWINSheriff It’s displayed when ’ setup is for PAL. [General tab in Setup See pg.11] Cause PAL Type has bigger image size than NTSC Backup Save Print Backup Motion detect play Viewer Event List Screen Division Multi-Speed play Zoom Ctrl Brightness Recording Motion...
  • Page 38 Running Search program From main screen click “Local Viewer (Search)” button. Choice Date and Time The Date has data, is marked in highlight on displayed calendar. Also the time is marked in highlight on selected date; Click the date and time, and the time which has data, is colored blue. Click on the blued data to display the data to the screen.

  • Page 39: Play Operation

    Play operation The slide bar of play panel corresponds to one hour. (the selected time) First End: It displays the first image of selected time. 1 Frame Backward: Backward retrieval per a 1 frame unit. Backward: Backward retrieval. The image recorded by MPEG4 is skipping the image of key frame unit to next key frame.
  • Page 40 Change property of a selected channel Each button is enabled when a channel is selected. if you want to change each property of the channel, move the slide bar to + or - . Also left/right arrow key is able to move slider bar. If you toggled each button, the property is reset.
  • Page 41 If you want to watch recorded data on Fast Forward/Fast backward, or watch the Data flame by flame, Set the display speed to what do you want(1x speed play is default. ) and then clicked Fast Forward or Fast Backward button. Motion Detect Mode Print Back-up...

  • Page 42: Back Up

    - Click the “Backup” button, start it. 2. DAT Back up jWINSheriff DAT Back up is a method that jWIN uses to back up the raw data of To invoke the feature; - Check “DAT” in Check Box. - Key in the start time and the end time.
  • Page 43 Retrieval Event List This function includes the running time and end time of DVR system, the controlled contents for running time and the event of sensor in action. jWINSheriff If you want to return another function from “Event List”, click again the button.

  • Page 44: Remote Viewer

    Remote Viewer...
  • Page 45 Screen Overview Save Print Image Quality To Muti Site To Single Site Connected Site List Warning Sign Display Exit Data Viewer Connect Site Setting Manager Manager Manager...
  • Page 46 Remote Digital Out VidChat Search Setup Alarm Switch Control Camera & Audio To Next Site To Prev/Next site Control & Stat PTZ Control...
  • Page 47 Registration Site information To see DVR’s image of remote site in Client program, you must register the site information. - Press the “Site Manager” button. - The pop-up window “Site Manager” will appear. - Choose a site name then enter the name into site manager. - Select the connect media.
  • Page 48 Storage Space Info Client’s Recording data has different System to Recorder, so each Site needs own storage Space. Also each DVR server needs their own storage space, and a hard disk driver is possible to get a server’s storage space. For example, if your computer has five hard disks driver, your computer is able to record data from five DVR Severs maximally.
  • Page 49 4. A window is popped up, and set storage space for recording by slide bar. and click “Make Storage Media” 5. Made storage space is displayed with Green as like that. and go to “schedule” tab in “Site Manager”...
  • Page 50 Remote Recording Schedule When Client is enabled you can save recording data from (audio and, or video) based on your predetermined schedule setting. If your client computer has storage space available, it will be able to record data based on the set schedule.
  • Page 51 Connect Site The registered sites come out at “Unbooked Sites”, double click the site that you want to connect, and if it’s connected with the site, come out the site name at “Sites on connection”. And press “OK” button, disappear the pop-up window, come out the connected sites at upper right side.
  • Page 52 Monitoring all cameras at a single site: Click the “Single Site” button, display the images Cameras connected. When you want to see the other site, press the arrow key below. The logging files of connection status Push the F9 Key, display the status of connection.

  • Page 53: Alarm Information

    Alarm Information Set up the alarm mode: if you clicked “Warning”, window about “Alarm Information” is popped up. On this window, if you check the Check-box “use Alarm window”, ”Alarm Information “is jWINSheriff popped up when Client got Alarm event from .
  • Page 54 Setting Manager “Setting Manager”, is used for unattended mode settings for all communications. -Unattended mode: if Alarm occurred from registered Site, Site is connected automatically by unattended mode for warning signal.
  • Page 55 Selecting the channel and the layout of channel If you select a channel which has an image, functional buttons (control PTZ, Recording, Print, canceling the image’s transmit, control the image quality) are enable to work. Print Image Quality Save Control PTZ (Pan Tilt Zoom) The PTZ control function is activated only for authorized users.
  • Page 56 Setting up the image quality to be transmitted You can set up the image quality. Transmitted Image count per second is changed by setting of the image quality. Cause higher Quality Image is Bigger size of Data. Save the transmitted image If you wanted to save an image which you selected a channel in a single site, click “Save”...
  • Page 57 Print out the transmitted image You can print out the transmitted image.
  • Page 58 Selection the site and the layout of channel Clicking “site name ” you want on the connected sites list, it is enable to click “Camera button, Audio button ,Remote Setup”, “Digital I/O” and etc. The activation of button is different according to the authority of ID. Digital-out VidChat Search...

  • Page 59: Remote Control

    Search As same as Digital out Switch, It’s cone out when the User has authority about search. Selecting the channel that you want, come out the date (the color become changes in the calendar that is recorded, and select the date, come out the time interval of that date. Selecting the time, it is activated the slider-bar and the button of retrieval, and can start to retrieval it.

  • Page 60: Dual Monitor

    Dual Monitor Two client applications is able to run as like picture on a computer, if your VGA graphic card supported dual monitor. If you have VGA card that support dual monitor, setup using dual monitor at Screen’s property. Click and run Client Icon on Screen. Click minimized button to hide client.
  • Page 61 WebAgent...
  • Page 62 Web Agent Install This Picture shows up when you insert Install CD Click “Install WebAgent” Button on Screen Web Agent Setting Use DVR Sever: if WebAgent was installed on a computer that had DVR and Set WebCam Server, Check on this button. USE Webserver to: If WebAgent was installed on a computer that is work server, and user didn’t check WebCam server, check this radio button, and you have to select the folder where “index.html”...
  • Page 63 Display Mode: Recommended Auto Display mode (Change Display mode automatically by connected Camera count). If you selected other mode (4, 8, 16 channel), you can choose channel which you want to watch. Check “Use Control”: Check “check box” for PTZ& Digital-Out Switch on Web Check “Use Window to check UserID”: If you checked this Check-BOX, you have to Login on Web-Agent page.
  • Page 64 How to use Web Agent by client Run Internet Explorer, write as like ”WebAgent installed server’s IP Address: port/ WebAgent installed folder path/” Default: WebAgent " If it was connected DVR site, we could see Web Agent on Internet Explorer. If your computer doesn’t have “Web Agent”, Window pop up and ask installing “Web Agent”...
  • Page 65 If Install was Success, we could see below picture (If Agent has Black Screen, Codec is not installed. Install MPEG4 Codec) If WebAgent was checked “Use Window to check UserID”, this window shows up for Login. and then you can see connected WebAgent as like this picture...
  • Page 66 How to use Web Agent You can see menu when you clicked right mouse button on screen Display Mode Screen Display mode is changed what you selected to 1, 4, 9, 16 division mode. Quality If you changed Quality, Displayed image size is changed. Also when you changed Quality, you have to consider about transmission speed of your system.
  • Page 67 Audio If you clicked this button, on control bar Speaker Icon is changed color to red, and then WebAgent play audio data if the selected channel had audio data. Also transmission speed is considered what your system has. Save Image If you clicked this button, you can save an image on selected channel to your computer.

  • Page 68: Web Service

    Web service...
  • Page 69 jWINSheriff jWINSheriff This is Web service for . It’s mentioned ‘s Setup page [Web server’s registration]. When User is Used Dynamic IP by DHCP of ADSL, Cable modem, this service make user be easy to watch Recorder. Because ,in dynamic IP, Recorder’s IP is change every time when Computer is turn on.
  • Page 70 There is two way to watch. One is jpg watch and the other way to connecting is mpeg. It works as like as ‘WebAgent’. Operation is as same as WebAgent,[Ref WebAgent] Operation is as same as WebAgent,[Ref WebAgent]...
  • Page 71 1. If you connected Web page www.inetdvr.com, Login page is shown up. 2. if you don’t have ID and password, click and sign up.
  • Page 72 3. when you finish Register, you’ll see this page. click “Add Site”, and register Site. Machine Name ID of The Machine Password of The Machine 4. After site register, do as like Fig. 5. If you want to connect to jpg, click jpg or if you want to connect to mpeg with Audio, some functions, click mpeg.

This manual is also suitable for:

Jd-vr80Jwinsheriff 4.2

Table of Contents