Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for NEW ENERGY BYEH-2500
- Page 1 Wall-mounted LEP battery user manual info@beny.com VERSION: 20231207-01...
-
Page 2: Table Of Contents
Contents 1. Note on This Manual 6. Troubleshooting 1.1 Scope of Validity 6 Troubleshooting 1.2 Target Group 1.3 Warning Signs 7. Maintenance 1.4 Some Symbols 7 Maintenance 8. Decommissioning 2. Safety 2.1 Safety Instructions 8.1 Dismantling the Battery 2.2 Response to Emergency Situations 2.3 Qualified Installer 9. -
Page 3: Note On This Manual
1. Note on This Manual Symbol Explanation This is the logo of Zhejiang Benyi New Energy Co.,ltd. 1.1 Scope of Validity This manual is an integral part of the battery pack. It describes the assembly, installation, commissioning, maintenance and failure of the This product has passed CE certification product. -
Page 4: Safety
Keep the battery pack away from children and animals. Risks of damage to the battery pack Do not allow the battery pack to get in contact with liquids. BYEH-2500 Do not subject the battery pack to high pressures. L*W*H: 470*340*180mm Do not place any objects on top of the battery pack. -
Page 5: Basic Features
3.3 Performance Specification Items Condition Handle BYEH-5000 Model BYEH-2500 Nominal energy Nominal value 2.66 5.22 Nominal capacity Nominal value Wall mount bracket Nominal voltage Nominal value 51.2 51.2 LED display Internal impedance Fresh cell ≤20 mΩ ≤20 mΩ Size L*W*H... -
Page 6: Installation
4. Installation 4.3 Precautions The battery is heavy. If it is improperly lifted or dropped during transportation or installation and disassembly, there is a risk of injury; There must be more than 2 people when hoisting, transporting and handling the battery; During battery wiring, one person shall wire and one person shall supervise and inspect to prevent battery short circuit;... -
Page 7: Tools
4.6 Tools These tools are required to install this product. Torque screwdriver Phillips screwdriver Hexagonal screwdriver Phillips screwdriver Torque wrench Slotted screwdriver Tape measure Electric drill 4.7 Installation 4.7.1 Check for Transport Damage Make sure the battery pack is intact during transportation.If there are any visible damages,such as cracks,please contact your BENY or your dealer immediately. -
Page 8: Cable Connection
4.7.4 Battery Installation Steps 4.8.2 Connecting Power Cables to Inverter Steps This step is going to connect power cables between Inverter and battery system. Make sure the wall is strong enough to withstand the weight of battery. The default length of power cables are 2 meters,you can appropriately cut the cable according to the actual installation environment. Step 1: fix the wall bracket on the wallUse the wall bracket as a template to mark the position of the holes Drill holes with driller,make sure Cable Connection Steps: the holes are deep enough (at least50mm)for installing and tightening the expansion bolts Install the expansion bolts in the wall,and tighten... - Page 9 4.8.3.1 CAN 4.8.4 Address assignment 1.Insert one end of the CAN communication cable directly to the port of the Inverter. Set the DIP switch on the battery panel, and assign the communication address of the battery module according to the table below. If there is 2.Insert the other end of the CAN communication cable to the CAN connector on the first battery.
-
Page 10: Overall Installation
4.9 Overall Installation ADD. 1.Connect the cables at one end of the battery. 2.Run the cables through the corrugated pipe. 3.Set the cables into the groove of metal plates and screw them back to the battery packs on both sides. 4.The last step is connecting the series-connected cable to"-"and "-"... -
Page 11: Buzzer Description
5.3 Buzzer Description 5.2.1 LED working status indication When the battery pack is powered on, the buzzer will give a long sound; Shut down and sleep, the buzzer gives a short sound; State SOC LED In case of short circuit protection, the buzzer will sound once every 2s. After the short circuit protection is locked for three times, the buzzer Explain will not sound again;... -
Page 12: Maintenance
The possible warning messages are as follows: If the battery has no display screen,refer to the LED display lamp Warning Messages Description Solution Cell overvoltage State Warning Messages Solution Stop charging protection Pack overvoltage Stop charging protection Overvoltage protection Stop charging Cell undervoltage Stop discharging protection... -
Page 13: Decommissioning
8. Decommissioning General Terms We guarantee that if the product is defective in manufacturing or materials, we will repair or replace the product or any part of it. We will try to replace the product with the same one. However, due to advances in technology, the product may not be available. In these cases, 8.1 Dismantling the Battery we will provide another type of product with at least the same value and standard, although the substitute product may be different in size, shape, color and/or capacity. -
Page 14: Scope Of Manufacturer Warranty
Scope of Manufacturer Warranty Costs of Submitting a Warranty Claim To provide high-quality services to end users, Zhejiang Benyi Electrical Co., Ltd.. We require an authorized dealer or dealer to respond to your For invalid claims under this Warranty, we will not be liable for the end-user’s costs in making the warranty claim, including transport or warranty claim.
Need help?
Do you have a question about the BYEH-2500 and is the answer not in the manual?
Questions and answers