McGrath Locks Ultra-Secua User Manual

Ultra-Secua
User Guide
mcgrathlocks.com.au
Download and Install the APP
Enable your smart phone to scan QR code to download
the APP. Also you can search "TT Lock" on APP store or
Google play to download the APP.
SETTING VIA LOCK
It is strongly recommended to use the TTLock APP, however you may follow the
programming instructions below to configure the lock manually.
CREATE NEW ACCESS
Add administrator (only 1)
123
New New
*12#
456#
Code# Code#
a. Enter *12# Tips: If you use the APP a 4 digit Admin
b. Input 123456# (the default code) code can be set. To change the APP Admin
through keypad press 83# + admin code#.
c. Input new code#
Now a new admin can be set via the APP.
d. Repeat new code#
Add a new user with an access / pin code (250 maximum)
Admin New New
*80#
Code# Code# Code#
a. Enter *80# Tips: If you use the APP a 4 digit user
b. Input admin code# code can be set.
c. Input user code# (6-9 digits)
d. Repeat new user code#
Add a new user with an RFID card (1000 maximum)
Admin
*80#
Code#
a. Enter *80#
b. Input admin code#
c. Present the card to the card sensor area
MODIFY CODE
Modify admin code
Admin New New
*12#
Code# Code# Code#
a. Enter *12#
b. Input old admin code#
c. Input new admin code#
d. Repeat the new admin code#
Modify user code
User New New
*10#
Code# Code# Code#
a. Enter *10#
b. Input old user code#
c. Input new user code#
d. Repeat the new user code#
DELETE USER
Delete specified pin code
Admin Specified
Tips: The admin code cannot be deleted.
*72#
Code# code#
a. Enter *72#
b. Input the specified code# that you wanted to delete
Delete all user codes
Delete all RFID cards
Admin
Admin
*71#
*69#
Code#
Code#
a. Enter *71#
a. Enter *69#
b. Input admin code#
b. Input admin code#
MANAGE VOICE
Turn on the lock voice Turn off the lock voice
Admin Admin
*30# 1# *30#
Code# Code#
a. Enter *30# a. Enter *30#
b. Input admin code# b. Input admin code#
c. Input 1# c. Input 0#
RESET THE LOCK
Press and hold the reset button until you hear "please input initialization passcode"
then input 000#. All pin codes, cards and APP users will be deleted.
DEMO MODE
Demo mode is turned off by default prior to an Admin code being registered. If you
wish to turn on demo mode input 24679#. Demo mode sets the lock access pin code
to 123456# and any card or fingerprint will also open it. Registering an Administrator
will take the lock out of demo mode.
LOW BATTERY ALERT
When battery power is less than 4.8V you will hear a low battery alert each time you
wake the lock screen. Please replace batteries with new Alkaline type. Don't mix old
and new batteries.
SCRAMBLING CODE FOR ANTI PEEP
Users may enter any random digits before or/and at the end of entering their correct
pin code and still gain access. This feature makes it harder for an unauthorised user
who may be watching you to guess your pin code.
INCORRECT CODE / CARD ALERT
If the wrong unlocking information is inputted five times the system will be locked out
for 35 seconds. The lock can only be operated by the APP during the lockout period.
PASSAGE MODE
Passage mode keeps the door unlocked, useful when gardening or bringing in
groceries from the car etc.
To activate passage mode, enter a valid unlock code then press 123# within
5 seconds. The door will remain unlocked.
To remove from passage mode, unlock using a valid code or card. If you
engage passage mode via the APP you must use the APP to disengage
passage mode.
FAQS
0#
Keypad on lock does not respond
1. Please check the batteries are installed correctly.
2. If the lock had been working OK please replace the batteries with new
AA Alkaline type.
The door will not lock
1. Ensure the lock is not in demo mode.
2. Check to see if the lock is in passage mode.
3. Refer to installation guide to ensure the triangle
on the lock hub is is correctly aligned.
Battery performance is poor.
1. Ensure all batteries are new Alkaline type.
2. Ensure the lock connecting cable is not pinched.
3. Check for and update lock firmware.