Summary of Contents for DQ Technology Streamax AD Plus2.0
- Page 1 DQTCAM ADPLUS 2.0 INSTALLATION DQTCAM CUSTOMERS GUIDE VERSION: 2.0 DATE: 10/30/2024 DQ TECHNOLOGIES...
-
Page 2: Table Of Contents
Table of Contents Introduction ................................. 3 System Overview ..............................4 Product Overview ............................. 4 Schematic Diagram of System Connection-Power Supply through Standard Power Cable ......5 Preparation for Installation ..........................6 Power Supply Connection of Vehicle ........................6 Power supply connection through the loose wire: ..................6 Installation Material and Tool List ........................ -
Page 3: Introduction
Introduction 1. Before installation, please park the vehicle on a flat surface and turn off the engine (do not park the vehicle on a ramp or an inclined road). 2. Review the packing list section of this document and check carefully while unpacking. 3. -
Page 4: System Overview
8. The Veyes App is required to debug and configure AD Plus2.0 during installation. Scan the QR code below, or search and download the Veyes app in the App Store. After download, you can connect the app with AD Plus2.0 to perform operations as needed following the instructions of the app. Android (Google Play Store) Apple iOs (App Store) System Overview... -
Page 5: Schematic Diagram Of System Connection-Power Supply Through Standard Power Cable
Schematic Diagram of System Connection-Power Supply through Standard Power Cable Dual-lens model Single-lens model DQ Technologies, Inc., phone: 512.248.8324 - www.dqtech.com... -
Page 6: Preparation For Installation
Preparation for Installation Technical Requirements for Installation • Be familiar with the functions, applications, and overall compositions of the product. • Understand the electrical circuits and structure of motor vehicles and common installation methods of in-vehicle devices. Understanding of Installation Environment. •... - Page 7 multiple cables have voltage within this range, select the one with the highest current as the constant power supply connection cable. ii. ACC Power: When the vehicle is in the ACC position or ignition state, use a multimeter to confirm that the voltage is around 24V or 12V. If the voltage is 0 when the vehicle is shut down and 24V or 12V in the ACC or ignition state, select this cable as the ACC power supply connection cable.
-
Page 8: Installation Material And Tool List
Installation Material and Tool List Packing List After unpacking the product, please confirm whether the Dashcam is intact and whether the accessories are complete. DQ Technologies, Inc., phone: 512.248.8324 - www.dqtech.com... -
Page 9: Tool List
Tool List The following installation accessories and tools will be needed Picture Tool Name Application Quantity Common screwdriver Tighten screws, optional 1pcs Crowbar Pry up the vehicle panel 1pcs Prepare Zip Ties Bundle cables needed Dry cleaning cloth Clean the dashboard 1pcs Install the Veyes App for video preview... - Page 10 Cut insulated rubber tape or Scissors 1pcs wire clip USB flash disk For future use 1pcs Locate vehicle power supply Multimeter 1pcs Measure the conduction of harness DQ Technologies, Inc., phone: 512.248.8324 - www.dqtech.com...
-
Page 11: Ad Plus2.0 Installation
AD Plus2.0 Installation Remove the lens protection stickers on the front and rear lenses of the Dashcam and tear off the protective film on the LED light on the front panel, as shown in the figure below. Selection of Dashcam Installation Area Requirements for installation area of AD Plus2.0: •... - Page 12 • The installation area is generally selected as shown in the figure below: DQ Technologies, Inc., phone: 512.248.8324 - www.dqtech.com...
-
Page 13: Installation Of Dashcam Bracket
Installation of Dashcam Bracket • Park the vehicle on flat sruface, clean the interior and exterior of the glass in the Installation area with alcohol wipe to ensure there is no dirt on the glass and ensure the glass is dry. •... -
Page 14: Installation Of Dashcam
Installation of Dashcam • Connect the Dashcam to the bracket with the front side facing inward (with the teeth on the right side of the bracket engaged with those on the right inner side of the Dashcam) and tighten the bracket clockwise with a PH2 cross screwdriver (before tightening, first adjust the Dashcam to be vertical). - Page 15 1) The center of the cab will be in the middle of the screen. 2) The cab screen shall be horizontal. 3) The vehicle steering wheel shall be shown at the lower right corner of the screen. The cab rendering after the lens for cab monitoring is properly adjusted as follows: Use a screwdriver to fasten the bracket studs clockwise so that the Dashcam will not shake easily.
-
Page 16: Power Supply Connection
Power Supply Connection • For hard/ loose wire installation: connect POWER/ACC/GND with the power cable of the vehicle, respectively. *Note: The power line shall be connected using a “special stripping-free connection terminal" where possible (no stripping is required, to avoid the risk of electric leakage), and the connection shall be wrapped with insulated rubber tape to avoid electric leakage/short circuit. -
Page 17: Cabling
Cabling • Upon the connection of the main cables according to the schematic diagram of system connection, as well as power supply connection, secure these cables using a crowbar according to the diagram below and conceal them in the interior trim panel or the dashboard (i.e. concealed cabling). •... -
Page 18: Fixing Position 2 Of The Power Supply Box
Fixing position 2 of the power supply box: Attach the power supply box to the right-side panel of the driver's seat, ensuring the cabling is exposed. Installing it on the left side panel is not recommended, as it may interfere with the door. -
Page 19: Installation Parameters Measurement Of The Adas Lens
*Note: • Within 3 min after startup, the Dashcam will automatically enable the WiFi transmission mode for debugging and connection with the app. If no connection is established with any app within 3 min, the Wi-Fi hotspot of the Dashcam will be OFF. On the login screen, enter the corresponding username and password. -
Page 20: Adas Lens Calibration
• Then, measure the front width (the distance between the outermost edges of both tires) and the front length (the horizontal distance from the ADAS lens to the license plate). Refer to the figure below for an example of how to measure these distances. Note: When the vertical height from the ground to the lens for road condition monitoring of AD Plus2.0 is measured, read the height value after making sure that the tower ruler or tape is perpendicular to the ground. -
Page 21: Automatic Calibration
Automatic calibration For manual calibration, there are two methods available, namely, the long-distance calibration method and the short-distance calibration method. However, since AD Plus2.0 is capable of automatic calibration, it is only required to enter the relevant parameters manually in the manual calibration process, and it is not necessary to perform the long- distance and short-distance calibration procedures completely. - Page 22 • Select the calibration channel. ADAS cameras are all installed on Channel 1, so select Channel 1. Then, tap Calibration at the lower-right corner of the screen to enter the calibration process • Confirm that the ADAS is installed at a proper position of the front windshield and within the working range of the wipers, and then tap Next DQ Technologies, Inc., phone: 512.248.8324 - www.dqtech.com...
- Page 23 • In the parameter input boxes, fill in the installation height of ADAS lens, the left margin of the ADAS lens, and the front-end width and front end length read in 5.1.2 respectively. Refer to the example on the right for the size measurement, with each parameter No.
- Page 24 Tap Next to enter the screen as shown below. • • Tap Next to enter the screen as shown below. Since AD Plus2.0 is capable of automatic calibration, it is only required to tap Next directly without adjusting the device on this screen. DQ Technologies, Inc., phone: 512.248.8324 - www.dqtech.com...
- Page 25 • Return to the real-time preview screen of the ADAS channel (by double-tapping the ADAS channel to enter the mainstream screen), and check and confirm that there is no calibration line superimposed on the screen at this time, which means that the ADAS channel has returned to normal mode.
-
Page 26: Cleaning
Cleaning Clean up the installation site, collect and take away tools and waste separately, and put the original articles in the vehicle to their original place, and then the installation work ends. Other documents available The following documents are also available for use. Contact support@dqtech.com for a copy •...
Need help?
Do you have a question about the Streamax AD Plus2.0 and is the answer not in the manual?
Questions and answers