Asus ZENBOOK UP5302Z Series Repair Manual
  1. Manuals
  2. Brands
  3. Asus Manuals
  4. Laptop
  5. ZENBOOK UP5302Z Series
  6. Repair manual
Asus ZENBOOK UP5302Z Series Repair Manual

Asus ZENBOOK UP5302Z Series Repair Manual

Hide thumbs

Advertisement

Table of Contents

ASUS ZENBOOK UP5302Z Series
Repair Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZENBOOK UP5302Z Series and is the answer not in the manual?

Questions and answers

Related Manuals for Asus ZENBOOK UP5302Z Series

Summary of Contents for Asus ZENBOOK UP5302Z Series

  • Page 1 ASUS ZENBOOK UP5302Z Series Repair Manual...
  • Page 3 Service Overview • ASUS is not responsible for direct, indirect, intentional o unintentional damages resulting from improper installation and operation. • Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs.
  • Page 4 Pre-repair checklist • Read the entire manual before starting any service procedures and follow all instructions. • Back up the data on your device. • Place your device on a clean and stable surface. • Turn off your device. • Disconnect all connected peripherals and cables.
  • Page 5 ASUS UP5302ZA Overview Top View Bottom View Top View 1. Array microphones 2. Camera indicator 3. Camera/IR Camera 4. 360°-adjustable touch screen panel 5. Microphone off indicator 6. Keyboard 7. Capital lock indicator 8. Touchpad/NumberPad 9. Ambient light sensor/RGB light sensor 10.
  • Page 6 Components Top View TOUCHPAD MODULE IO BOARD LCD COVER WIFI ANTENNA BASE CASE TP FFC MAIN BOARD TOUCH PANEL CONTROLLER BD IO Cable KEYBOARD MODULE THERMAL MODULE ASSY SPEAKER TOUCH CONTROL CABLE BATTER Back...
  • Page 7 Components Bottom View KEYBOARD MODULE THERMAL MODULE ASSY MAIN BOARD BASE CASE LCD MODULE TOUCHPAD MODULE Back...
  • Page 8 Repair Overview This chapter describes disassembly and assembly (Assemble document please look up from the last page), please follow the information provided in this section to perform the complete disassembly procedure. Precautions: Before you perform any service or repair on the notebook, please pay special attention to the cautions prevent any damages to the notebook. 1.
  • Page 9 ASUS ZENBOOK UP5302Z Series Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble the notebook Screwdriver Alcohol 95% Glove Dust-free Cloth Please accord to different screw specification to choose different screwdriver and head. Plastic Blade Thermal Pad Substitute: G500 Thermal Grease) Plastic Tweezers Use a pair of tweezers to remove/insert/tidy cables.

  • Page 10: Bottom Case

    BOTTOM CASE Disassembly Notice Screws Spec Torque (kgf-cm) Step 1 : Remove screws*9pcs. SCREW M2*2.5L 2±0.2 Step 2 : Use plastic blade to pry the bottom case. Start Please follow above arrow direction To avoid the bottom case hook, with using plastic blade to pry bottom don't insert plastic blade in each red circle.
  • Page 11 DISCONNECT BATTERY CONNECTOR Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Step 1 : Use the non-conductive pry tool to push iron sheet.
  • Page 12 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Screws Spec Torque (kgf-cm) Step 1 : Tear off the UP5302ZA MAIN BD MYLAR*1pc. Step 2 : Remove the screw*1pc and M.2 card (SSD). SCREW M2*2L 2.0±0.2 Step 3 : Remove the AL MYLAR and tear off the SSD Thermal Graphite Sheet.
  • Page 13 Assembly Notice Please be sure to pull out adapter and disconnect the battery. Paste the UP5302ZA MAIN BD MYLAR*1pc on the motherboard. Paste the SSD Thermal Graphite Sheet on the new M.2 card (SSD), then assembly AL MYLAR *1pc. Assembly steps: When installing the SSD, please keep the SSD less then 15 degrees Align and insert the new M.2 card into the module slot.
  • Page 14 BATTERY Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Screws Spec Torque (kgf-cm) Step 1 : Tear off the MYLAR.

  • Page 15: Wlan Antenna

    WLAN ANTENNA Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect Antenna Cable . Step 2 : Tear off the C300MA-2A ACETATE TAPE. Step 3 : Remove Antenna Cable . Assembly Notice Tear off When you change the keyboard module, please follow the mark below to paste a new ANTENNA and tidy the cable.
  • Page 16 SPEAKER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect the SPEAKER connector. Step 2 : Remove SPEAKER. Assembly Notice For Speaker assembly, please follow the below steps. 1. Please follow the marker to assembly speaker mylar. 2.

  • Page 17: Thermal Module

    THERMAL MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screws*4pcs. Torque(kgf-cm) Screws Spec Step 2 : Remove the THERMAL MODULE from MB and top case. SCREW M2*2L 2±0.2 Recommend that the force point is at green block and pull up thermal module to take it out.

  • Page 18: Main Board

    MAIN BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the UP5302ZA TYPE C ABSORBER MYLAR. Torque(kgf-cm) Step 2 : Remove all red mark cables. Screws Spec Step 3 : Remove screws*7pcs. Step 4 : Remove MB.
  • Page 19 MAIN BOARD Materials on mainboard UP5302ZA CPU BRKT RUBBER 13NB0VV0L63011 13NB0VV0L07011 UP5302ZA LCD B CAP MYLAR//TENYI 13NB0VV0L43011 UP5302ZA MB RUBBER UP5302ZA LED RUBBER 13NB0VV0L23011 Back...
  • Page 20 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Step 1 : Remove screws*3pcs. Torque(kgf-cm) Screws Spec...
  • Page 21 FP MODULE AND IO BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Screws Spec Torque (kgf-cm) Step 1 : Remove FP MODULE. Step 2 : Remove screw 2pcs. SCREW M2*2L 2.0±0.1 Step 3 : Tear off the mylar and remove IO Cable. Step 4 : Remove IO Board.
  • Page 22 MAIN BOARD Mainboard connector placement CAM CABLE EDP CABLE IO CABLE K/B FPC SPEAKER BATTERY TP/MB FFC Back...

  • Page 23: Touchpad Module

    TOUCHPAD MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Screws Spec Torque (kgf-cm) Step 1 : Disconnect TP connector and remove the TP FPC. Step 2: Remove screw 4*pcs. SCREW M2*2L 2.0±0.1 Step 3 : Tear off the mylar. Step 4 : Remove the TOUCHPAD MODULE.

  • Page 24: Lcd Bezel

    LCD BEZEL Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the LCD B CAP ASSY. Step 2 : Remove TOUCH PANEL CONTROLLER BD and TOUCH CONTROL CABLE. Remove Step 1-1, Start from the middle area of each side of bezel, Using the forefinger to hold the outer edge firmly and the thumb flipping the Assembly Notice bezel inner edge outward to release the hooks as indicated in the diagram shown.

Table of Contents