Sealey CH2013.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to DO NOT
instruction cover
manual
NOTE: THIS PRODUCT IS ONLY SUITABLE FOR USE IN WELL INSULATED AREAS OR OCCASIONAL USE.
1. SAFETY
i
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
9
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products.
Electrical safety information. It is important that the following information is read and understood:
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Important: Ensure that the voltage rating on the appliance suits the pow er supply to be used and that the plug is fitted with the
Correct fuse.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by a
8
qualified electrician.
If the cable or plug is damaged during use, switch off the elect ricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
Familiarise yourself with the applications and limitations of the heater.
9
Ensure that heater housing is positioned with feet and tilt switch on a firm, horizontal dry surface.
9
Keep away from flammable objects/materials/surfaces. This product gets very hot during use. Use in a location where accidental
9
contact (particularly by children) is unlikely.
Ensure the 4 position switch is set to 'off ' before connecting power cord to power supply.
9
Ensure the heater is in good order and condition before use. If in any doubt DO NOT use the unit and contact an electrician.
9
Keep tools and other items away from the heater when it is in use.
9
Keep the area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the heater, as it gets very hot.
9
Disconnect from mains and allow to cool before moving or attempting any cleaning.
9
DO NOT get the heater wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT remove plug from mains supply by pulling on power cord.
8
DO NOT move the heater whilst in operation or even when still warm.
8
DO NOT disassemble the heater for any reason. The heater must be checked by qualified personnel only.
8
DO NOT use this product to perform a task for which it has not been designed.
8
WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. If it blows again DO NOT use the unit and
‰
contact an electricianDO NOT place any object on the heater at any time.
WARNING! Ensure any object is at least 200cm from the heater front face.
‰
DO NOT leave unattended. When not in use, store the heater carefully in a safe, dry, childproof location.
8
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack
of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they DO NOT play with the appliance.
2. INTRODUCTION
Stylish modern design heater with two heat settings of 700/1400W. Features PTC heat conducting ceramic elements to achieve an
instant, odour-free heat. Thermostat control to maintain ambient temperature at preset level. Includes overheating protection and tilt
safety switch, protecting the user, product and environment.
© Jack Sealey Limited
CERAMIC FAN HEATER 1400W/230V
2 HEAT SETTINGS
MODEL NO:
Warning: Warning:
Electric shock Hot surface
hazard
Original Language Version
CH2013.V3
Indoor use
only
CH2013.V3 Issue 3 (2) 19/09/23