Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Metallkraft BTS 51
Summary of Contents for Metallkraft BTS 51
- Page 1 Operating Instructions Belt and Disc Grinding Machine BTS 51 BTS 51...
-
Page 2: Table Of Contents
11.3 Disposal of lubricants........13 12 Troubleshooting........13 13 Spare parts..........14 Subject to technical modifications and error. 13.1 Ordering spare parts........14 13.2 Spare parts drawing........15 14 Electrical wiring diagram.....16 15 EC - Declaration of Conformity....17 BTS 51 | Version 2.03... -
Page 3: Introduction
Spare part orders: Fax: 0049 (0)951 96555-119 Email: ersatzteile@stuermer-maschinen.de We are always interested in valuable experience and knowledge gained from using the application, which then could be shared and be valuable to develop our products even further. BTS 51 | Version 2.03... -
Page 4: Tips And Recommendations
If the machine is used for commercial purposes, the op- - Have all works only performed by qualified persons. erating company must comply with the legal working - Keep insufficiently qualified persons and children safety regulations. out of the working area. BTS 51 | Version 2.03... -
Page 5: Personal Protective Equipment
- Do not pull at the mains cable in order the pull the mains connector from the power socket. Protect the ca- ble against heat, oil and sharp edges. BTS 51 | Version 2.03... -
Page 6: Safety Signs On The Belt And Disc Grinding Machine
Claims of any kind for damage due to improper use are The machine must be put out of operation from the mo- excluded. ment when the labels are unable to be recognized and understood at first glance, until new labels are attached. BTS 51 | Version 2.03... -
Page 7: Residual Risks
(indirect con- tact). - Heat generation on components can lead to burns Fig. 2: Type plate BTS 51 and other injuries. 4.3 Dimensions - Risk of injury to fingers and hands from the tool or workpiece, e.g. -
Page 8: Transport, Packaging, Storage
5.3 Storage The Belt and Disc Grinding Machine must be stored thor- oughly cleaned in a dry, clean and frost-free environ- ment. Fig. 4: Description of BTS 51 1 Drive disc 2 Grinding belt 3 Graphite support 4 Wheel... -
Page 9: Scope Of Delivery
- The installation site must have adequate lighting (see workplace regulations and DIN EN 12464). - The humidity should not exceed 60%, and the measured room temperature should be in the range of 0 °C - 40 °C as a maximum. BTS 51 | Version 2.03... -
Page 10: Changing The Grinding Wheel
- The operator must not work if he is overworked or suffers from fatigue and difficulties in concentrating. - The Belt and Disc Grinding Machine may only be operated by one person. Other persons must not enter the working area during operation. BTS 51 | Version 2.03... -
Page 11: Starting The Machine
The edge of the workpiece must be positioned in a START button for this. way that a maximum gap of 2 mm results in order to prevent a pinching of workpieces or fingers between table and grinding disc. BTS 51 | Version 2.03... -
Page 12: Switching The Machine Off
- If required, disassemble the machine into easy-to-han- dle and usable components and parts. - Supply the machine components and operating materi- als to the provided disposal routes. BTS 51 | Version 2.03... -
Page 13: Disposal Of Electrical Devices
NOTE! These components must be disposed of separately and Contact your neared Metallkraft dealer if you are una- professionally. In case of doubt, please contact your mu- ble to solve the problems with your machine. Please nicipal waste management company. -
Page 14: Spare Parts
Information on the unit type, item number and year of manufacture can be found on the type plate attached to the machine. BTS 51 | Version 2.03... -
Page 15: Spare Parts Drawing
In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 7: Spare parts drawing BTS 51 BTS 51 | Version 2.03... -
Page 16: Electrical Wiring Diagram
Electrical wiring diagram 14 Electrical wiring diagram Switch KJD12 Engine Fig. 8: Electrical wiring diagram BTS 51 BTS 51 | Version 2.03... -
Page 17: Ec - Declaration Of Conformity
Safety of machinery - General principles for design - Risk assessment and risk reduction DIN EN 60204-1:2019-06 Safety of machinery - Electrical equipment of machines - Part 1: General requirements Responsible for documentation: Kilian Stürmer, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 24.05.2022 ______________________ Kilian Stürmer Manager BTS 51 | Version 2.03... - Page 18 www.metallkraft.de...
Need help?
Do you have a question about the BTS 51 and is the answer not in the manual?
Questions and answers