EcoxGear SOUNDEXTREME SEI-SEMRN1DINAU Installation Manual
  1. Manuals
  2. Brands
  3. EcoxGear Manuals
  4. Marine Radio
  5. SOUNDEXTREME SEI-SEMRN1DINAU
  6. Installation manual
EcoxGear SOUNDEXTREME SEI-SEMRN1DINAU Installation Manual

EcoxGear SOUNDEXTREME SEI-SEMRN1DINAU Installation Manual

1 din marine radio
Hide thumbs

Advertisement

Table of Contents

1 DIN Marine Radio
Model: SEI-SEMRN1DINAU
Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SOUNDEXTREME SEI-SEMRN1DINAU and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for EcoxGear SOUNDEXTREME SEI-SEMRN1DINAU

Summary of Contents for EcoxGear SOUNDEXTREME SEI-SEMRN1DINAU

  • Page 1 1 DIN Marine Radio Model: SEI-SEMRN1DINAU Installation Guide...

  • Page 2: Warranty

    Important · Please read this Installation Guide and the User Guide before installation and use. If you are unsure about installing this product, please contact a professional audio installer. · The 1 DIN Marine Radio is designed to be installed into standard 1 DIN openings, or a smaller custom opening (refer to Mount the Radio in a New Location for details), in boats, golf carts, cars, and off -road vehicles.
  • Page 3 Important · You will need to connect the (Purple) Remote Turn-On Wire to the vehicle ignition switch with the supplied (Purple) Remote Turn-On Extension Cable. If you are not able to connect it to your vehicle ignition switch, connect this input to a rocker switch (not included), then connect the rocker switch to a 12V-to-56V power supply on your vehicle or to a switch accessory panel.
  • Page 4 Important into Standby State. If you press the Power Button again, it will turn on the Radio. · The Radio saves its Turn On (Power On) and Standby last state into memory. When you turn on your vehicle’s ignition switch, the Radio will go back to the same Power State that it was in before it was Powered Off .
  • Page 5 1 DIN Marine Radio Overview 1 DIN Marine Radio Layout Front Panel IP67 Dirtproof and Waterproof FM/AM Antenna 12V Power-In SAE Connector Jack and Remote Turn-On Wire J3 Connector J2 Connector Jack – J1 Connector Jack – Jack – LED Aux-In, RCA Outputs, Speaker Outputs and Lighting Controls...
  • Page 6 1 DIN Marine Radio Overview Inputs and Outputs 12V Power-In SAE Connector Fuse Holder Power Input SAE Connector: Power input (+12V and GND) with in-line 35 Amp Fuse Holder. Remote Turn-On Wire Remote Turn-On Input Wire: This (Purple) input wire connects to an ignition switch signal (or rocker switch or any switch accessory panel).
  • Page 7 1 DIN Marine Radio Overview · Vehicle Signals (Brake, Reverse, Left Turn, Right Turn): 4 Pins – Optionally connects to your vehicle for brake, reverse, left turn signal, and right turn signal integration with LEDCast-enabled speakers, strips, and whips. 2. Outputs: 9 Pins ·...
  • Page 8 1 DIN Marine Radio Overview J2 Connector Jack: The J2 Connector Jack has 14 pin assignments (pins 3, 13, and 14 are not used): 1. Aux-In Input: 3 Pins – This is a stereo line input with Red and White RCA jacks for right and left channels.
  • Page 9 1 DIN Marine Radio Overview J3 Connector Jack: The J3 Connector Jack has 12 pin assignments: · LED Lighting Control Outputs – These outputs are assigned to 4 Zones. Each Zone has 3 pins (12V, GND, and signal). Each 3-pin, female, round LED connector supports a maximum 5A power output.

  • Page 10: Installation And Wiring

    Installation and Wiring Safety and Wiring Considerations · For easier assembly, it is recommended you run all wires prior to mounting your unit in place. · Pre-plan your system layout and best wiring routes to save installation time. Carefully route all system wiring away moving parts and sharp edges;...
  • Page 11 Installation and Wiring Power Input and Remote Turn-On 1. Power In – An 2.4m 12 AWG SAE Power Cable is included for you to connect the Radio to your vehicle’s 12V battery. When you determine the power requirement from your battery, you need to check both the power consumptions on the audio and the LED lighting controls.
  • Page 12 Installation and Wiring Audio Input, Output, and Vehicle Signal Input Cable Harnesses The three remaining wiring harnesses are designed to connect to different external devices. CABLE HARNESS EXTERNAL DEVICE CONNECTOR J1 Connector Non-Amplifi ed Speakers, Bare Wires Cable Harness Amp-On, Dim-In, Vehicle Signals J2 Connector Audio Power Amplifi...
  • Page 13 Installation and Wiring LABEL COLOR WIRE HARNESS DEFINITION White / Black Audio Out Zone 1 Left Speaker (-) White Audio Out Zone 1 Left Speaker (+) Gray / Black Audio Out Zone 2 Left Speaker (-) Gray Audio Out Zone 2 Left Speaker (+) Purple Audio Out Zone 2 Right Speaker (+) Purple / Black...
  • Page 14 Installation and Wiring J2 Connector Cable Harness: The J2 Connector Jack has 14 pin assignments (pins 3, 13, and 14 are not used). LABEL COLOR WIRE HARNESS DEFINITION White 1 Sub Out Zone 1 White 1 Sub Out Zone 1 Gray Audio Out Zone 2 Gray...
  • Page 15 Installation and Wiring J3 Connector Cable Harness: The J3 Connector Jack has 12 pin assignments. LABEL COLOR WIRE HARNESS DEFINITION Purple LED Lighting Control Zone 4 (Right) Output Purple LED Lighting Control Zone 4 (Right) Output Purple LED Lighting Control Zone 4 (Right) Output Blue LED Lighting Control Zone 3 (Left) Output Blue...
  • Page 16 Installation and Wiring System Wiring Layout 12V Power-In +12VDC (Red) Fuse Holder Remote Turn-On SAE Connector Wire (Purple) Ground (Black) J1 Connector Cable Harness J2 Connector Cable Harness J3 Connector Cable Harness...
  • Page 17 Installation and Wiring Audio Out Zone 1 Left Speaker Audio Out Zone 2 Left Speaker (+) White Wire (+) Gray Wire (-) White / Black Wire (-) Gray / Black Wire Audio Out Zone 2 Right Speaker (+) Purple Wire (-) Purple / Black Wire Amplifi...

  • Page 18: System Wiring

    Installation and Wiring System Wiring None of the input and output extension cables are included, except the Power and Remote Turn-On Extension Cables. You only need the extension cables for the specific features you need, depending on the external devices you wish to connect to your Radio. When you obtain the extension cables for wiring, please follow the guidelines listed below.
  • Page 19 Installation and Wiring signals. Make sure you power off all the vehicle equipment and disconnect vehicle power supply from the vehicle’s battery BEFORE you make any wire connections. 3. Isolate and seal all the unused wires / leads on the J1 Cable Harness.
  • Page 20 Installation and Wiring 3. Connect vehicle signal inputs: · If you want your Radio’s LCD screen to automatically dim when your vehicle’s lights are on, connect your vehicle’s illumination wire to the Dim-In input on the J1 Cable Harness. · If you connect LEDCast Products to the Zone 3 and 4 LED lighting control outputs on J3 Cable Harness, and want to use the Vehicle Signaling Features (see details below), connect to the Vehicle’s brake, reverse, left turn, and right turn signals to...
  • Page 21 Installation and Wiring Align the arrow on both connectors, push in and screw the nut cap on the female connector. Then connect the 3-pin male connector on the LED Extension Cable to the female connector on the LEDCast Product. · If the cable is longer than required, do NOT cut the cable and reconnect.
  • Page 22 Installation and Wiring · Zone 1 and Zone 2 Speaker Audio Outputs – There are two Speaker Audio Outputs for Zone 1 and two for Zone 2. You may wish to separate your external speakers into each Zone according to their location on your vehicle. For example, 2 speakers located toward the front of your vehicle can be designated to Zone 1, while 2 speakers near the rear can be designated to Zone 2.
  • Page 23 Installation and Wiring Green), and Vehicle Right Turn Signal Wire (Light Blue) to their corresponding vehicle signals. 4. Remote Turn-On to Ignition Switch Connection: · Before you make a connection to your vehicle’s ignition switch, make sure the vehicle’s power supply cable is disconnected from your vehicle’s battery.
  • Page 24 Installation and Wiring 5. Connecting the included Power Cable to your Vehicle’s 12V battery is the last step of the wiring installation, but first, proceed to the following Mount Your Marine Radio instructions. Mount Your Marine Radio Safety and Mounting Considerations ·...
  • Page 25 Installation and Wiring Mount the Radio in a New Location If you need to cut an opening on your vehicle, follow the steps below. 1. Trim the included paper template to the size that fi ts your mounting area. Then adhere it to the mounting surface. 2.
  • Page 26 Installation and Wiring 8. Connect all of the wires and cables: · Plug the J1, J2, and J3 Cable Harnesses and FM/AM antenna (sold separately) into the back of the Radio. · Connect the Remote Turn-On Extension Cable to the Remote Turn-On Input Wire.
  • Page 27 Installation and Wiring If you are placing the Radio into a single DIN stereo, follow the steps below. 1. Pass all the appropriate wires and cables through the EVA Gasket and the DIN Cage. 2. Slide the included DIN Cage into the DIN opening or the existing DIN fi...

  • Page 28: Product Warranty

    Installation and Wiring Connect Power and Turn on Your Marine Radio After the installation (mounting, wirings, cable connections) is completed, check the following before you connect the Power Cable (+12V, GND) to your vehicle’s battery: · Make sure the ignition switch is tuned off . This is to prevent your vehicle’s engine from being started automatically and unexpectedly when you reconnect the vehicle power supply cable to the battery.
  • Page 29 Installation and Wiring IMPORTANT: BEFORE use, you MUST verify your wiring and installation as follows: 1. Check Audio Device Connections: · Check Zone 1 and Zone 2 Speaker Audio Outputs – Play Music (e.g., an audio playback via Bluetooth). Check if the Audio Zone Volume Controls on the Radio changes the sound outputs for the speaker in the corresponding Zone.
  • Page 30 Installation and Wiring · If your Radio has Vehicle Signal Inputs AND LEDCast Products connected to Zone 3 and 4, check the following: · When your vehicle’s left turn signal is on, the LEDCast Product (on the left) connected to Zone 3 will fl ash Yellow. ·...
  • Page 31 Next, read your User Guide to explore more features and functions for your 1 DIN Marine Radio...
  • Page 32 Need Additional Protection? Visit soundextreme.com.au to purchase a soft, silicon-rubber cover for your 1 DIN Marine Radio’s front panel. V08.23...

Table of Contents