1. Manuals
  2. Brands
  3. PESA Manuals
  4. Electronic dictionary
  5. UCI-2000-S
  6. Manual

PESA UCI-2000-S Manual

Protocol translator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
81-9059-0545-0 Rev. C
UCI-2000-S P
Document Number 81-9059-0545-0 Revision C
PESA
ROTOCOL
UCI-2000-S P
T
RANSLATOR
S
ERVICE AND
T
ROTOCOL
RANSLATOR
O
A
RDERING
SSISTANCE
PESA Switching Systems, Inc.
103 Quality Circle, Suite 210
Huntsville AL 35806 USA
www.pesa.com
M
O
AIN
FFICE
Tel: 256.726.9200
Fax: 256.726.9271
S
D
ERVICE
EPARTMENT
Tel: 256.726.9222 (24/7)
Toll Free: 800.323.7372
Fax: 256.726.9268
Email: service@pesa.com
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UCI-2000-S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for PESA UCI-2000-S

  • Page 1 81-9059-0545-0 Rev. C UCI-2000-S P ROTOCOL RANSLATOR UCI-2000-S P ROTOCOL RANSLATOR ERVICE AND RDERING SSISTANCE PESA Switching Systems, Inc. 103 Quality Circle, Suite 210 Huntsville AL 35806 USA www.pesa.com FFICE Tel: 256.726.9200 Fax: 256.726.9271 ERVICE EPARTMENT Tel: 256.726.9222 (24/7) Toll Free: 800.323.7372 Fax: 256.726.9268...
  • Page 2 Original Printing © 2003 PESA Switching Systems, Inc. All Rights Reserved. UCI-2000 is a trademark of PESA Switching Systems, Inc. in the United States and/or other countries. Microsoft, Windows, and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
  • Page 3 RANSLATOR About This Manual This manual provides detailed instructions for the installation, operation, and maintenance of the PESA UCI-2000-S Protocol Translator. Warnings, Cautions, and Notes Warning statements identify conditions or practices that can result in personal injury or loss of life.

  • Page 4: Table Of Contents

    Figure 3. Cabling ..........................4 Figure 4. Sony to PESA Mode....................... 5 Figure 5. PESA to Sony Mode....................... 6 Figure 6. Control Cable Connections, Sony to PESA Mode ..............11 Figure 7. Control Cable Connections, PESA to Sony Mode ..............12 List of Tables Table 1.

  • Page 5: Chapter 1 - Introduction

    The PESA UCI-2000-S protocol converter is designed to provide an interface between Sony and PESA routing switchers and control systems. The UCI-2000-S can operate in one of two distinct modes, allowing PESA routing matrices to be controlled by a Sony control system and control panels or allowing Sony routing matrices to be controlled by a PESA 3500 family control system.

  • Page 6: Chapter 2 - Installation

    2.1 Receipt Inspection The UCI-2000-S Mainframe was tested and inspected prior to leaving the factory. Upon receipt, inspect the equipment for shipping damage. If any damage is found, contact the carrier and PESA immediately and save all packing material. 2.2 Unpacking The UCI-2000-S Mainframe is comprised of 1RU chassis/backplane assembly, one UCI2000 protocol translator card and one SRU Power Supply.

  • Page 7: Mounting

    RANSLATOR 2.4 Mounting The UCI-2000-S Mainframe is rack mounted in a standard 19” equipment rack. Sufficient space must be provided behind the rack to allow for the control and power cables. All mounting holes should be utilized and mounting hardware tightened securely. As with all equipment installed in a rack, the bottom screw on each side should be installed before proceeding with the remainder of the screws.

  • Page 8: Cabling

    Stepping or tripping on the cables may result in connections being pulled free or wire breakage inside the insulation. The UCI-2000-S Mainframe should be installed in the equipment rack prior to attaching cables. Use the following rules when cabling the UCI-2000-S Mainframe: 1.

  • Page 9: Chapter 3 - Setup And Operation

    Chapter 3 – Setup and Operation 3.1 Sony to PESA Mode The Sony to PESA control mode allows the UCI-2000-S to control up to eight levels of PESA PRC-based routing switchers from the Sony control system. Each of the eight additional levels can support a matrix size of 256 x 256 inputs and outputs.

  • Page 10: Pesa To Sony Mode

    RANSLATOR 3.2 PESA to Sony Mode The PESA to Sony control mode allows the UCI-2000-S to control up to eight levels of Sony S- BUS based routing switchers from a PESA 3500 family control system. Each of the eight additional levels can support a matrix size of 256 x 256 inputs and outputs. These control levels must occupy a consecutive block in the level space of the PESA control system and cannot share an existing level with a PESA router.

  • Page 11: Hardware Configuration

    3.3.2 Setting the Sony S-BUS Station Address For all operating modes, dip switch S3 is used to set the station address (ID) of UCI-2000-S on the Sony S-BUS data link. The ID is set using a binary representation using switches 1-8. Valid station addresses are 2-254.

  • Page 12: Setting The Control Levels

    (bit per level) representation. For example: turn on switch 2 for level 2, switch 3 for level 3, and so on. If more than one PESA level is being controlled, the level numbers do not have to be consecutive. For example, the PESA matrices can operate on levels 2 and 5 by turning on switches 2 and 5 on S4.

  • Page 13: Configuring The On-Board Jumpers

    8, all Sony routers are set to start at levels 1-8 regardless of where they "really" exist in the PESA control system. The UCI-2000 automatically offsets the base PRC strobe number when sending commands to the Sony routers and assumes all Sony routers exist starting at level 1 (native to Sony).

  • Page 14: Software Configuration

    3.4 Software Configuration 3.4.1 Sony to PESA Mode To enable the new PESA routers in the system, they must be added to the configuration in the Sony control system software. The PESA routers are added and configured exactly as if they were Sony routers.

  • Page 15: Cable Connections

    UCI-2000-S P ROTOCOL RANSLATOR 3.5 Cable Connections 3.5.1 Sony to PESA Mode: COM1: PRC - Connect to PESA Routers COM2: RS232 Terminal/PC (38400,N,8,1) COM3: Not Used SYSTEM V CONTROL (37-pin): Not Used BNC #4: Connect to Sony S-BUS Controller and Routers Figure 6.

  • Page 16: Pesa To Sony Mode

    RANSLATOR 3.5.2 PESA to Sony Mode: COM1: Not Used COM2: RS232 Terminal/PC (38400,N,8,1) COM3: PRC - Connect to PESA 3500 family control system SYSTEM V CONTROL (37-pin): Not Used BNC #4: Connect to Sony S-BUS Controller and Routers Figure 7.
  • Page 17 81-9059-0545-0 Rev. C UCI-2000-S P ROTOCOL RANSLATOR PESA...

Table of Contents