Summary of Contents for Ensemble Designs BrightEye
- Page 1 BrightEye and BrightEye NXT Rack Mount Assembly Kit Installation Guide Models BERKMT-FULL and BERKMT-RR Revision 1.3...
-
Page 2: Table Of Contents
BrightEye Rack Mount User Guide Contents Overview List of what is included in your BrightEye Rack Mount Kit (BERKMT-FULL or BERKMT-RR) Illustrations and associated letters for components in the BrightEye Rack Mount Kit Installing a BrightEye NXT in the Rack Mount, Overview... -
Page 3: Overview
All installation can be done from the front, so it’s easy to mount the BrightEye Rack Mount into your rack and then populate it. Blank filler panels may be installed in unused spaces, if desired. See the illustrations below for a few examples of how the rack can be populated. -
Page 4: List Of What Is Included In Your Brighteye Rack Mount Kit (Berkmt-Full Or Berkmt-Rr)
BrightEye Blank Filler Panel for the BrightEye Rack Tray (BERKMT-FULL only) G 52002239 Note: Two BrightEye rack mount kits are available to meet your needs. The BERKMT-FULL kit includes blank filler panels and the BERKMT-RR does not. Illustrations and associated letters for components in the BrightEye Rack Mount Kit The following pages show detailed illustrations of the components in the BrightEye Rack Mount Kit, and reference the letter associated with each part. - Page 5 BrightEye Rack Mount User Guide BrightEye to NXT Retainer, front and rear views Referred to in this document as part Note: This asymmetrical part intentionally has three holes so that it can be flipped 180 degrees to accommodate retaining a BrightEye/NXT combination in any position.
- Page 6 NXT Blank Filler Panel, front and rear views (Two included in BERKMT-FULL kit) Referred to in this document as part front rear BrightEye Blank Filler Panel, front and rear views (Two included in BERKMT-FULL kit) Referred to in this document as part front rear www.ensembledesigns.com...
-
Page 7: Installing A Brighteye Nxt In The Rack Mount, Overview
Install the appropriate front retainer See the below illustration for an overview, and the detailed instructions on the following pages. Illustration for installing a BrightEye NXT, using a NXT to NXT front retainer (D), and a NXT Retainer Washer (E), exploded view www.ensembledesigns.com... -
Page 8: Installing A Brighteye Nxt In The Rack Mount, Details
Installing a BrightEye NXT in the Rack Mount, Details • Remove the four rubber feet from the bottom of the BrightEye NXT. To remove, apply side pressure with your thumb, the feet are held on with adhesive and will pop off. - Page 9 BrightEye to BrightEye Retainer (C) NXT to NXT Retainer (D), shown in below illustration Illustration of two BrightEye NXTs installed in the rack mount, using a NXT to NXT front retainer (D), and a NXT Blank Filler Panel (F), assembled view www.ensembledesigns.com...
-
Page 10: Installing A Brighteye In The Rack Mount
BrightEyes stacked as shown in the far left position of the illustration below. If you are installing just one single-high BrightEye in one of the positions and a fully dressed out rack is desired, a BrightEye single-high blank panel (BEBP) may be ordered to fill the open space. - Page 11 BrightEye Rack Mount User Guide The below illustration is an example for installing a combination of BrightEyes and a BrightEye NXT in a rack mount. Two single-high BrightEyes, stacked One double-high BrightEye One BrightEye NXT Illustration of BrightEyes and a BrightEye NXT installed in the rack mount, using a BrightEye to BrightEye front retainer (C), a BrightEye to NXT front retainer (B) and an NXT Retainer Washer (E), exploded view www.ensembledesigns.com...
-
Page 12: Using Blank Filler Panels In The Rack Mount
The NXT blank filler panel and the BrightEye blank filler panel (both shown below) can be installed in any of the three positions in the rack mount. If you are installing just one single-high BrightEye in a position, a BrightEye single-high blank panel (BEBP) may be used to fill the remaining space (not shown and not included in BrightEye Rack Mount Kits). -
Page 13: Additional Parts Order Info
BrightEye Blank Filler Panel for the BrightEye Rack Tray 52002239 6-32 x 1/2” Phillips Flat Black Z/P Machine Screw w/Nylock 30001147 BrightEye Single-High Blank Panel – BEBP BrightEye single-high blank panel – Ensemble Designs order info: BEBP www.ensembledesigns.com BrightEye Rack Mount - Page 13... -
Page 14: Troubleshooting
There’s a gap between the blank filler panel and the side of rack mount When the BrightEye Blank Filler Panel is installed in either the left or right position, there is an intentional gap between the Blank Filler Panel and the side of the rack mount.
Need help?
Do you have a question about the BrightEye and is the answer not in the manual?
Questions and answers