Summary of Contents for Canadian Solar CSI-WIFI-2
- Page 1 Quick Installation Guideline Model:CSI-WIFI-2 Warning: 1. Please remove logger after power off. 2. Reset button supports direct press. Do not remove waterproof plug.
- Page 2 Notice: Please read this manual carefully before using products and keep it in the place where O&M providers can easily find. Due to product upgrade and other factors, the content of this manual might change from time to time. Please take actual product as standard and get latest manual from sales.
- Page 3 1. Stick Logger Installation Step1: Assemble logger to the inverter communication interface as shown in the diagram. According to the arrow direction. Step2: Install/Remove Install Remove C l o c k w i s e r o t a t i o n C o u n t e r - c l o c k w i s e r o t a t i o n Warning: Please do not hold the logger body to rotate while...
-
Page 4: Logger Status
2. Logger Status 2.1 Check Indicator light Lights Implication Status Description(All lights are single green lights.) 1.Light off: Connection to the router failed. 2.On 1s/Off 1s(Slow flash): Connection to the router succeeded. Communication 3.Light keeps on: Connection to the server succeeded. with router 4.On 100ms/Off... - Page 5 READY Fault Description Fault Cause Solution READY 1.Check the con- nection between stick logger and inverter. Remove 1.Connection betw- the stick logger een stick logger and and install again. inverter loosen. Slow Communication with 2.Inverter does not 2.Check inverter state flash inverter abnormal match with stick log-...
- Page 6 READY Fault Description Fault Cause Solution READY 1.Connection betw- 1.Check the con- een stick logger and nection, remove the inverter loosen or stick logger and in- abnormal. stall again. Power supply 2.Inverter power in- 2.Check inverter ou- abnormal sufficient. tput power. 3.Stick Logger abn- 3.Contact our cust- ormal.
- Page 7 4. Usage methods and notices for Reset button 4.1 Usage methods and key-press descriptions for Reset button Usage: Press Key-press Status Description Light Status SMARTLINK rapid networking Short press 1s NET light ashes fast for 100ms. status. All lights are extinguished Long press 5s Rebooting the stick logger.
- Page 8 Warning: Please make sure the stick logger is working properly before you leave the site. If there is anything abnormal, please do not leave the site and contact customer service at the first time. If you have any technical queries about our products, please contact us and provide the following information: 1.
- Page 9 APP USER MANUAL...
-
Page 10: Download App
Download APP CSI Cloud CSI CloudPro for end user for business 1.Registration Clik [Register] to creat new account.You can use email to register. - Page 11 2. Create Plant 2.1 Click [Add Now] to start creating a plant. On the next page, please select the way you create the plant as prompted. If you choose to create your own power station, please proceed as described below. Please confirm the location of the plant and related necessary information on the next page, fill in according to your actual situation, and then click the [Finish] button to complete the...
- Page 12 Now you can see the plant you just created on the home page. Click the [Check the plant] button to view detailed data for the plant.
-
Page 13: Add A Device
3.Add a device 3.1 Click the [+] button in the upper right corner of the home page, select Add a Logger, and select theplant where you want to add the device in the next page. You can choose to scan the barcode of the collector or directly enter the SN number below the barcode to add it, then click the [Add] button to go to the next page. - Page 14 On this page, you can stipulate how the logger selects the device associated with it. The default mode is “Automatic Selection”. If you do not have special requirements, please click the [Done] button to confirm. After the confirmation is completed, the logger will be added to the plant.
-
Page 15: Smart Link Configuration
Smart Link configuration （1）Enter networking page-short press reset button for 1S-NET light flashing-Entering configuration mode. （2）Make sure the phone connected the WiFi network, entering WiFi password, starting to configure. - Page 16 （3）The signal lights slowly flash or keep on indicate that the net- work has been successfully accessed, otherwise it fails. Please check again in a few minutes. If the signal lights are still not normal, please reconfigure it. Notice： 1.During configuration, it will show configuration tips. 2.If the configuration process lasts more than 20s, configuration failed, entering the next step(The picture below will show the next step.
- Page 17 AP configuration （1）Please make sure that the phone is connected to the WiFi net- work and enter the WiFi password. APP will automatically get the current mobile phone WiFi account, type in the WiFi password to enter the configuration process. If the ne- twork is not the one logger needs to configure, switch the network.
- Page 18 Notice If it is unable to find an AP_XXXXX(S/N) in wireless network list, please make sure the distance between WiFi router and stick logger is less than 10 meters. If there is any problem during the connection or setting process, you can repeat the above steps. If you still cannot find the AP_XXXXX, you can check the logger manual for troubleshooting or contact our Customer Service.
- Page 19 If you encounter following situations, please reconfigure logger network : 1. Change router 2. Change WIFI password 3. Change router's SSID 4. Enterprice routers may restrict WIFI connectivity. Warning: Please make sure the stick logger is working properly before you leave the site. If there is anything abnormal, please do not leave the site and contact customer service at the first time.
Need help?
Do you have a question about the CSI-WIFI-2 and is the answer not in the manual?
Questions and answers