Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Rinieri CPL
Summary of Contents for Rinieri CPL
- Page 1 Head 2015 Pre-Pruning Vine Cane Remover Head Instructions for use and maintenance The following instructions must be read carefully prior to using the machine. In accordance with article 2006/42/CE SERIAL and subsequent modifications...
- Page 2 In regards to safety and reliability this machine was designed in accordance with the provisions and subsequent revisions set out in the The manufacturer therefore cannot be held responsible for machine use where modifications have been made without prior For safety issues not covered in this text please refer to general standards concerning the prevention of accidents. Below is a list of definitions, descriptions and abbreviated terms most frequently used in the text.
-
Page 3: Ec Declaration
Page intentionally left blank... -
Page 4: Table Of Contents
INDEX DESCRIPTION EC DECLARATION INDEX INTRODUCTION GENERAL INFORMATION INSTRUCTION MANUAL PRESERVATION AND CARE OF MANUAL IN HOUSE TESTING DELIVERY INSPECTION PACKAGING MACHINE DETAILS RECOMMENDATIONS DESCRIPTION OF THE MACHINE Pre-pruning machine TECHNICAL SPECIFICATIONS TECHNICAL FEATURES COMMISSIONING SYSTEMS HYDRAULIC LAYOUT COMMANDS IDENTIFICATION DATA ADHESIVES SAFETY REGULATIONS SYMBOLS TO REMEMBER... -
Page 5: Introduction
INTRODUCTION Dear Customer, the purpose of this text is to introduce you to the basic standards and criteria you have to follow in order to use and maintain this machine and thus it must be read before using the machine. If any part of this publication is not understandable please consult your retailer as this is a necessary precondition to using this machine safely. -
Page 6: Very Important
DESCRIPTION OF THE MACHINE The CPL head is used for the cutting and removal of the shoots in spurred cordon and Guyot system vineyards, and surely represents one of the most economical solutions for this agricultural job. -
Page 7: Commissioning
COMMISSIONING If the driving vehicle is not fitted with three-pin outlets, adapt the plant of the same with the three-pin outlets provided with the machine, taking the wiring diagram at the side as a reference. Connect a group cables with 4 mm² section and max. impedance of 18 A, directly to the driving vehicle 12 V battery, for every three-pin coupling to be added to the existing plant. -
Page 8: Identification Data
By pressing the red mushroom shaped button on the emergency command box, the machine opens leaving conveyor rotation free at a slower speed, and remains open while the button is pressed. The fuse-holder houses a 5x20WF 10A 250V glass fuse. Magnet Fixing Mushroom-Shaped emergency button Burndy 8-pin connector... -
Page 9: Safety Regulations
CAUTION Rotating parts on the machine. Wait for all parts to have completely stopped before proceeding to checking or intervening on the machine. CAUTION Suitable safety individual equipment must be worn. CAUTION Danger: machinery may suddenly shift Hook for hoisting and handling the machinery. laterally. -
Page 10: Improper Use
When you have to drive on streets to reach the work place, make sure that the machine is in line with the moving vehicle and that it does not cover possible lighting and signal systems; if this is not possible, put the machine on a type-tested tow. -
Page 11: Connecting The Hydraulic System
Start the motor and keep it ticking over, activate oil delivery to the command unit and then test all machine movements, up to limit switch. Remember that the movements must always be performed slowly and evenly. Pay attention never to switch tool rotation on during movement. Make sure that the disc towers turn freely, that there are no abnormal noises or vibrations and there are no leaks in the hydraulic system. -
Page 12: Safety Measures
- When using the pruner with the pre-pruning head, to prevent the pre-pruning head from becoming misaligned due to its own weight, run the screw along the slot of the frame quick-coupling, overcoming the resistance of the tension spring, insert the safety block into the slot of the frame quick-coupling and take the safety tab into the block position. -
Page 13: Pressure Adjustments On The Machine
Pressure adjustments on the machine: Valve: A V max standard calibration 120 Bar adjusts the pressure on the conveyor motors B Flow adjuster max 10 l/min adjusts the delivery oil flow rate at the opening jack, we adjust the opening speed of the cages. C V max on jack maximum opening pressure at 30 Bar It is recommended to operate on the valves only if necessary and using relevant manometers for reading the pressures. -
Page 14: Hydraulic System Maintenance
Remember that disposal and law regulates collection of used oil. Take the aforementioned residues to the appropriate disposal center or keep them in tanks and call specialized companies to dispose of them. them to illegal dumps or to dump them in rivers or sewers. HYDRAULIC SYSTEM MAINTENANCE The standard machine can work with the mineral oil of the tractor, like Mobil Multivariax/35 HP with viscosity grade ISO VG 68, with the following limitations. -
Page 15: Transport - Hoisting - Movement
Problem Cause Solution The part between the wires does not close The emergency command box selector is Take the selector to the work position (see towards the wire not in the work position commands chapter) Restore the power supply by correctly No power supply or polarity inverted in connecting the plug and/or correct polarity the three-pin outlet, which has been added... -
Page 16: Conditions Of Guarantee
CONDITIONS OF GUARANTEE This machine is guaranteed for 12 months from the date of purchase. The guarantee covers the replacement of parts agreed as initially defective and for errant assembly operations. breakage caused by negligence or non observance of the standards outlined in this manual. Use or maintenance carried out by untrained or unskilled persons.
Need help?
Do you have a question about the CPL and is the answer not in the manual?
Questions and answers