Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Holzstar SAA 2203 UT
- Page 1 Instruction Manual Dust collector SAA 2203 UT SAA 2203 UT...
-
Page 2: Table Of Contents
12.2 Spare parts drawing........14 12.3 Parts list ............15 13 Electrical schematic ..........16 14 EC-Declaration of Conformity......17 Copyright information Copyright © 2022 Stürmer Maschinen GmbH, Hallstadt, Germany. Technical changes and errors excepted. SAA 2203 UT | Version 1.03... -
Page 3: Introduction
Ordering spare parts: Fax: 0049 (0) 951 96555-119 E-Mail: ersatzteile@stuermer-maschinen.de We are always interested in information and experiences that result from the application and can be valuable for the improvement of our products. SAA 2203 UT | Version 1.03... -
Page 4: Responsibility Of The Operator
SAA 2203 UT | Version 1.03... -
Page 5: Personal Protective Equipment
The personnel must wear personal protective equipment during the various work on and with the ma- chine, which is referred to separately in the individual sections of these instructions. Fig. 1: Safety labels SAA 2203 UT | Version 1.03... -
Page 6: General Safety Measures
- Do not vacuum flammable gases or materials (e.g. - The use of an incompletely assembled unit. paint or paint mist) or metallic parts. - Modifications to the unit or the use of modified ac- - Only use original spare parts. cessories. SAA 2203 UT | Version 1.03... -
Page 7: Residual Risks
- Danger from wood dust - Hazard to the upper limbs in case of accidental Fig. 2: Dimension drawing contact with the fan wheel 4.3 Type plate Fig. 3: Type plate SAA 2203 UT | Version 1.03... -
Page 8: Description Of The Device
Employees must be outside the dan- ger zone, the reach of the load. - Machine body Warn employees and point out the danger to employ- ees. - Filter bag - Dust bag - 4x Rollers - 2x Tension belt SAA 2203 UT | Version 1.03... -
Page 9: Packaging
- Do not set up or operate the machine in a damp or wet environment. The humidity should be in the range of 30% to 95% and the measured ambient temperature should be between +5°C to +50°C. SAA 2203 UT | Version 1.03... -
Page 10: Electrical Connection
The ends of the metal wire are then connected to the conductive housing of the extraction system and the machine to be extracted. Machine Suction Fig. 8: Insert filter and dust bag Fig. 9: Connection machine and exhaust system SAA 2203 UT | Version 1.03... -
Page 11: Commissioning
- Change and empty the filter and dust bag. Monthly maintenance - Check the fastening screws of the machine and tighten them if necessary. - Check electrical safety devices and guards and re- place immediately if necessary. SAA 2203 UT | Version 1.03... -
Page 12: Cleaning
Step 2: If necessary, dismantle the machine into mana- geable and recyclable assemblies and compo- nents. Step 3: Route the machine components and operating materials to the designated disposal channels. SAA 2203 UT | Version 1.03... -
Page 13: Troubleshooting
Example used. The motor for the Dust collector SAA 2203 UT must be - In case of any uncertainties, always contact the manu- ordered. The motor has the number 28 in the spare parts facturer. -
Page 14: Spare Parts Drawing
The following drawing should help to identify necessary spare parts in case of service. To order, send a copy of the parts drawing with the marked components to your authorized dealer. Fig. 10: Spare parts drawing SAA 2203 UT | Version 1.03... -
Page 15: Parts List
Washer Nut M8 Packing Allen screw M6x20(LH) Power cable Bag strap Filter bag Dust bag Engine Washer Screw M10x16 Washer Screw M8x30 Control box complete Screw M6x16 Screw M6x10 Washer Nut M4 Mounting plate SAA 2203 UT | Version 1.03... -
Page 16: Electrical Schematic
13 Electrical schematic Bez. Designation Quantity Five pin connector RS-515 Fuse Fuse 10A RT28-N-32X ON-switch LAY 37 OFF switch LAY 37 AC contactor CJX2 0910 Thermal relay LR2-D1312 5.5-8A Motor Motor Fig. 11: Electrical schematic SAA 2203 UT | Version 1.03... -
Page 17: Ec-Declaration Of Conformity
≤ 16 A per phase and not subject to conditional connection Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 26.05.2021 ______________________ Kilian Stürmer Manager SAA 2203 UT | Version 1.03... - Page 18 www.holzstar.de...
Need help?
Do you have a question about the SAA 2203 UT and is the answer not in the manual?
Questions and answers