Advertisement
Quick Links
Advertisement
Summary of Contents for Showven Maiman 30W
- Page 1 USER MANUAL Maiman 30W/40W/60W V1.1 2024/11/01 Showven Technologies Co., Ltd.
- Page 3 Thanks for choosing SHOWVEN Maiman series laser, we wish it will bring you lots of exciting ® moments. Please read the following manual carefully before operating this product. Safety Considerations Δ Before proceeding any further, please read the following safety considerations very carefully. It could help you avoid dangerous and hazardous situations which could lead to serious injury or property damage.
-
Page 4: General Safety Information
If you lost this manual please always contact info@showven.cn for a new one. Disclaimers: SHOWVEN technologies Co., Ltd holds no responsibility for injuries or damages caused by the use of this laser display equipment. SHOWVEN excludes liability for unsafe situations, accidents and damages resulting from: Ignoring warnings or regulations as shown on product housing or this manual. - Page 5 Warning Labels Δ Warning Label According to IEC 60825-1 regulations, the laser with continuous high-output greater than 500mW belongs to Class IV, Class 4 laser. The optical warning label is as follows, please pay attention!
- Page 6 “laser radiation”) with the same amplitude and phase that are flowing in the same direction to form a laser beam. SHOWVEN Maiman series full-colour RGB lasers using premium semiconductor laser diodes as the light source, ensure bright colors, high brightness, and realistic animation effects;...
- Page 7 Maiman 30 Δ Dimension Technical Specifications Model: Maiman 30 Output: 30W Dimension: 495× 471× 226mm Weight: 27kg Power Input: AC100-240V, 50/60Hz Wavelength: 638nm (R), 520nm (G), 445nm (B) Scanning System: ± 30°, 35K Analogue modulation: 100K, Analog/TTL Beam Size: 6× 7mm Beam Divergence: <1.2mrad Cooling System: TEC cooling Waterproof Level: IP65...
- Page 8 Maiman 40 Δ Dimension Technical Specifications Model: Maiman 40 Output: 40W Dimension: 495× 471× 226mm Weight: 29kg Power Input: AC100-240V, 50/60Hz Wavelength: 638nm (R), 520nm (G), 445nm (B) Scanning System: ± 25°, 30K Analogue modulation: 100K, Analog/TTL Beam Size: 6× 8mm Beam Divergence: <1.2mrad Cooling System: TEC cooling Waterproof Level: IP65...
- Page 9 Maiman 60 Δ Dimension Technical Specifications Model: Maiman 60 Output: 60W Dimension: 634× 508× 253mm Weight: 50kg Power Input: AC100-240V, 50/60Hz Wavelength: 638nm (R), 520nm (G), 445nm (B) Scanning System: ± 20°, 25K Analogue modulation: 100K, Analog/TTL Beam Size: 7× 12mm Beam Divergence: <1.5mrad Cooling System: TEC cooling Waterproof Level: IP65...
- Page 10 Quick Operation Sheet Δ 1. Installation For safety, laser should be installed on a stable truss or elevated platform. Please also use safety rope and clamp for extra safety. International laser safety regulations require that laser products must be operated as shown below, with a minimum vertical distance of 3 meters between the floor and the lowest laser beam.
- Page 11 4. Install E-stopper or E-STOP terminator (if not install E-stopper for remote control) to the REMOTE IN. Maiman series with remote E-stop functions by connect E-STOPPER with REMOTE IN, and serveral units of lasers can be connected in series to be controlled by a single E-STOPPER as below.
- Page 12 8. Switch safety lock to ON status, please double check it is safe to play the laser. 9. Operation with QuickShow, Beyond etc software. Please follow FB4 operation in this manual or FB4 operation manual from Pangolin. 10. Turn off laser output on software 11.
- Page 13 FB4 and control these directly through an ethernet network. To modify settings or change operating modes, you can use the control knob in conjunction with the LCD display. SHOWVEN Maiman series laser with three connection mode. 1. Direct connection between computor and a single unit of Maiman Laser NOTE: The Ethernet port on FB4 is invalid, there is no signal input to this port.
- Page 14 2. Connect computor and multi units of Maiman Lasers in series / daisy chain 3. Connect computor with multi units of Mainman Lasers through switch NOTE: It is recommended to connect multiple laser in series via Ethernet port. DB25 interface series connection may cause FB4 signal conflict and image distortion.
- Page 15 [Slave Mode] [Autoplay] allows for scheduling shows across multiple projectors. When setting up a show which uses multi FB4’s, one laser will need to act as master. This laser will need to be set in operational mode [Autoplay]. Other FB4’s that need to perform in the same show, must be placed in operation mode [Slave mode] so that they will follow the master FB4.
- Page 16 File3.ILD,18,4 After creating the folder, create a PRG file with the file name in the same folder, and edit all playback files to this PRG file. The editing speed here is the playback speed in ILDA mode. For example, create the folder "Laser show" and create the file "Laser show.PRG" under this folder; after adding a new ILDA file, we need to add this ILDA file to the PRG playlist so that we can ILDA mode correctly finds this file and plays it at the desired speed.
- Page 17 161-223 Next 225-255 Stop 0-31 Original cue color 0-255 Color Scroll 33-223 Color Scroll 8 Bit 225-255 White Reserved Reserved 8 Bit * If a BPM based effects is exported at 100BPM, and you want to have a cue running on 128 BPM, change the speed to 128.
- Page 18 Size and Position setting Set the size X and Y to 80. Master setting Set the master size VERY IMPORTANT NOTICE: Please set the parameters strictly according to the above parameters, otherwise the galvanometer may be damaged!
- Page 19 Beam Alignment Δ Beam Alignment only allowed to be performed by professional authorized technicians. Please read the following information carefully and take your time to process them! If you are not 100% certain that you understand the beam alignment principle, DO NOT ATTEMPT to proceed with the beam alignment by yourself.
- Page 20 Trouble Shooting Δ Q Laser projector doesn’t work or no laser output. A: 1. Check whether the power cable is well connected, check whether fuse is burned out. 2. Check power supply in consistent with the rated voltage of the equipment. 3.
- Page 21 Packing List and Optional Parts List Δ Item No. Description pcs / unit Remark Micro SD card Standard E-STOP terminator Standard Power cable Standard Optional Ethernet cable 5-pin DMX cable Optional 3-pin DMX cable Optional E-STOPPER Optional Safety rope Optional Clamp Optional Items with remark of “Standard”...
- Page 22 Damage caused by external reasons (lightning strike, power supply etc.) Damage caused by improper installation or use; For product damage not included in warranty range, we can provide paid service. Invoice is necessary when applying for maintenance service from SHOWVEN ®...
- Page 24 Showven Technologies Co., Ltd. Tel: +86-731-83833068 Web: www.showven.cn E-mail: info@showven.cn Add: No.1 Tengda Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, 410300, P.R.China...
Need help?
Do you have a question about the Maiman 30W and is the answer not in the manual?
Questions and answers