Summary of Contents for SpectRah ARV-35 Series
- Page 1 ARV-35XX AD Board (Hardware version A1. X) Model Name ARV-3500 (RGB, LVDS) ARV-3510 (HDMI & RGB, LVDS) ARV-3520 (RGB, DVI, LVDS) Copyright © 2015 Spectrah Dynamics Inc., all rights reserved...
-
Page 2: Table Of Contents
Table of Contents Introduction 1.1 Overview 1.2 Check List 1.3 Contact Information Hardware Installation Guide 2.1 Set BIOS Jumpers 2.2 Set Panel VDD 2.3 Set Backlight VDD 2.4 Set Brightness Control 2.5 Connect panel cable 2.6 Connect backlight power 2.7 Connect OSD touch pad 2.8 Connect power adapter to turn on system 2.9 Connect signal input cables 2.10 Power on your computer... - Page 3 4.2 Feature Description 4.2.1 Image 4.2.2 Display 4.2.3 Audio 4.2.4 System Product Specifications Customer Support Notice...
-
Page 4: Revision History
Revision History Version Date Page Section Description Product Document A1.x 2015/01/23 3.12/3.14 TX/RX defined A1.x 2014/10/07 First Release... -
Page 5: Introduction
Guide in Section 2 and Hardware Information in Section 3 for details and ensure each switch, connector, and jumper are set properly. We truly believe you will enjoy using the Spectrah ARV-35XX series products. Thank you for making this Spectrah AD converter board as your choice. -
Page 6: Check List
Display cable kits (Optional) Inverter (Optional) LED backlight driver (Optional) LED light sensor (Optional) 1.3 Contact Information Spectrah Dynamics, Inc. 5F-2, No. 188, Sec# 3, Ta-Tung Road, Hsi-Chi, Taipei Hsien 221, Taiwan Tel: 886-2-86472026 Fax: 886-2-86472201 Website Address: www.spectrah.com... -
Page 7: Hardware Installation Guide
2. Hardware Installation Guide WARNING - Static electricity can severely damage electronic parts. Take these precautions: Before touching any electronic parts, be sure you are properly grounded or that static electricity is discharged from your body. You can do this by touching the metal frame of your computer. ... -
Page 8: Set Bios Jumpers
ARV-35XX again to reset system and get new display timing. The following tables depict the jumper setting and associated display timing. Please refer to Spectrah’s panel selection guide or contact Spectrah’s customer service center to get correct BIOS setting for your LCD panels. - Page 9 F35-1.22x BIOS Jumpers Item SW1-SW2-SW3-SW4-SW5 Panel Timing Type Resolution Jumpers ON-ON-ON-ON-ON 1024768-LS LVDS 1024x768 OFF-ON-ON-ON-ON 6B-1024768-LS LVDS 1024x768 ON-OFF-ON-ON-ON 1024768-CMO-LS LVDS 1024x768 OFF-OFF-ON-ON-ON 6B-1024768-CMO-LS LVDS 1024x768 ON-ON-OFF-ON-ON 12801024-LS LVDS 1280x1024 OFF-ON-OFF-ON-ON 6B-12801024-LS LVDS 1280x1024 ON-OFF-OFF-ON-ON 1440900-LS LVDS 1440x900 OFF-OFF-OFF-ON-ON 6B-1440900-LS LVDS 1440x900 ON-ON-ON-OFF-ON...
-
Page 10: Set Panel Vdd
2.2 Set Panel VDD There are 3 jumpers (JP701, JP702, JP703) to allow user to set suitable VDD for LCD panels. Please refer to panel specifications in power voltage of LCD module before connecting to ARV-35XX series. Otherwise, onboard +12V or +5V VDD setting in ARV-35XX series may damage your LCD panel requiring lower power supply voltage like +5V or +3.3V. -
Page 11: Connect Power Adapter To Turn On System
2.8 Connect power adapter to turn on system Connect power cable from power adapter to CN901 or CN902 power connector (+12V DC is required). The LED of OSD-476 lights red and under normal condition, a small No Signal screen appears on the panel in 3 seconds. If no change on LED or panel screen, please check power adapter and cable, and make sure they are connected firmly. -
Page 12: Update Firmware Bios
In addition, if the horizontal noise appears on the panel screen, please select Image feature to adjust Phase to reduce the noise. 2.12 Update firmware BIOS CN605 allows user to use Spectrah’s cable tool and program to upgrade new firmware BIOS through RS232 interface. 2.13 Connect detection device (Optional) ARV-35XX allows user to connect external detection card like Spectrah’s... -
Page 13: Hardware Information
3 Hardware Information Board Dimension: 110 (L) x 100 (W) mm PCB Version:A1.X... - Page 14 ARV-35XX layout No. Definition A RS-232 PORT (reserved) B IR (reserved) C Backlight Connector (JST S7B-PH compatible) D Jumpers for Backlight Voltage Setting E Jumpers for LCD Panel Voltage Setting F OSD Connector G Jumpers for Brightness Control H BIOS Switch Jumpers I BIOS Programming Port J 5-pin Wafer Power Connector K DC Jack Connector...
-
Page 15: Bios Jumpers
Note1: The voltage of JP203 is dependent on the input voltage from the DC power adapter. If the required DC output voltage of power adapter is not +12V, please contact Spectrah’s FAE to get support. JP201 JP202 JP203 +3.3V... -
Page 16: Brightness Control Jumpers
LCD panel, LED driving board, or inverter before you set up both jumpers. Normally, if LED driving board is integrated in LCD panel, user needs PWM signal for dimming control. Most Spectrah’s inverters and LED boards need DC voltage for brightness control. -
Page 17: Backlight Connector
ARV-35XX series. User can select either one connector as the major power input port. Connect power cable from power adapter to CN901 or CN902 power connector (+12V DC is required). Please contact Spectrah’s FAE to get support if the output DC voltage of power adapter is not +12V. - Page 18 Warning! The DC voltage in JP203, JP703, and pin1/2 of CN201 is the same as that from CN901/CN902 (+12V DC). Please refer to 3.2 and 3.3 for details. Don't connect pin-1 (+5V) of CN901 except special OEM hardware version which requires external +5V DC (External +5V DC power connecting to onboard +5V DC from power regulator may cause power voltage fluctuation.)
-
Page 19: Audio Input/ Output Connectors
CN 801 3.12 BIOS programming port CN605 (JST S4B-PH compatible, 2.0 pitch) CN605 allows user to use Spectrah’s programming tool to upgrade new firmware BIOS through RS232 interface. The following table depicts the pin definition of CN605. 3.13 External Detection Port CN604... -
Page 20: Mode Table
3.14 Mode Table SVGA 640 x 480 @ 60HZ 800 x 600 @ 60HZ 1024 x 768 @ 60HZ 640 x 480 @ 70HZ 800 x 600 @ 70HZ 1024 x 768 @ 70HZ 640 x 480 @ 72HZ 800 x 600 @ 72HZ 1024 x 768 @ 72HZ 640 x 480 @ 75HZ 800 x 600 @ 75HZ... -
Page 21: Osd Setup
4 OSD Setup 4.1 General Description The ARV-35XX series features an on-chip OSD (On-Screen Display) controller that creates the OSD user interface menus and overlays them onto the output data stream. User can adjust the display conditions on LCD monitor using the OSD-476 touch pad. After powering on, the AD controller restores itself to the last known conditions saved in Non-Volatile Random Access Memory (NVRAM). -
Page 22: Image
4.2.1 Image Brightness - Press S3 or S4 to adjust the brightness of LCD backlight directly. This feature should work together with the inverter or LED driver which provides PWM (Pulse Width Modulation) or DC Voltage control feature. The PWM or DC voltage control pin of backlight should be connected to pin-6 of CN201. -
Page 23: Audio
Light Sensor - Press S2 and hold for 5 seconds to enable light sensor function. This icon will allow user to enable or disable Spectrah’s light sensor SR2901. If users don’t need to use Spectrah’s light sensor, please select OFF to disable this function. Otherwise, the brightness control appears unstable and users will see flash on panel screen. - Page 24 reset. The previous setting stored in NVRAM will be released after Factory Reset is enabled. This feature helps users return back to original default setting in NVRAM, especially when users get problems when adjusting OSD features.
-
Page 25: Product Specifications
5 Product Specifications ADC Controller Genesis Full HD Scaler Adaptive color and contrast enhancement (Genesis ACC & ACM-II features) 10-bit triple-channel ADC/PLL Scaling engine OSD controller Hue, Saturation, Brightness, Contrast, Color Temperature adjustment Input Port DB-15 analog VGA interface (All series) DVI- I digital interface (ARV-3520 only) HDMI digital interface (ARV-3510 only) Audio input interface (ARV-3510 only) - Page 26 ARV-35XX series. Around 50~60 Watt power adapter is recommended to supply +12V DC power for ARV-35XX series and LCD panels under 22” size. For more detail in power requirement, please contact Spectrah Customer Service Center for more information.
- Page 27 Board Dimension 110 (L) x 100 (W) mm Weight ARV-3500 (110g) ARV-3510 (115g) Operating Temperature & Humidity -20℃ to 80℃; ~90%RH Storage Temperature & Humidity -40℃ to 95℃; ~ 95%RH...
-
Page 28: Customer Support
Your dealer is local and may be familiar with your complete system. According to the warranty, the product must be returned to the dealer, who will return it to Spectrah. Fax Support: Call our dial-up Spectrah fax service at 886-2-86472201. -
Page 29: Notice
Specifications and information contained in this manual are furnished for informational use only, and are subject to change at any time without notice and should not be construed as a commitment by Spectrah Dynamics. Copyright © 2015 Spectrah Dynamics Inc., all rights reserved...
Need help?
Do you have a question about the ARV-35 Series and is the answer not in the manual?
Questions and answers