Kampmann Katherm QE Assembly, Installation And Operating Instructions
Hide thumbs
Also See for Katherm QE:
Subscribe to Our Youtube Channel
Related Manuals for Kampmann Katherm QE
Summary of Contents for Kampmann Katherm QE
- Page 1 Katherm QE ► Assembly, installation and operating instructions Keep these instructions in a safe place for future use! Issue09/24EN-US SAP No.1280354...
-
Page 3: Table Of Contents
Table of contents 1 General ..........................5 1.1 About these instructions ........................1.2 Explanation of Symbols.......................... 2 Safety............................ 6 2.1 Correct use............................. 2.2 Limits of operation and use........................2.3 Risk from electrocution!......................... 2.4 Dangers from hot surfaces ........................2.5 Personnel requirements - Qualifications ....................2.6 Personal Protective Equipment ...................... - Page 4 10.2 Maintenance Schedule:.......................... 33 10.3 Maintenance work ..........................33 10.3.1 Clean the inside of the unit ........................33 11 Faults ............................ 34 11.1 Fault table.............................. 34 11.2 Start-up after rectification of fault ......................34 12 Intertek Certificate Katherm QE.pdf..................36...
-
Page 5: General
Katherm QE Assembly, installation and operating instructions General About these instructions These instructions ensure the safe and efficient handling of this equipment. These instructions form an integral part of the equipment and have to be kept in the direct vicinity of the equipment and available to personnel at all times. -
Page 6: Safety
Correct use Katherm QE are used to heat indoor spaces (e.g. living rooms, commercial spaces and showrooms). Within the room to be heated, the unit needs to be connected to the in-situ power grid. Observe the operating limits and limits of use described in Chapter 2.2 [} 6]. -
Page 7: Risk From Electrocution
Katherm QE Assembly, installation and operating instructions WARNING! Danger due to incorrect operating voltage It is essential that the operating voltage given on the type label of the unit is observed. Incorrect operating voltage will result in incorrect operation of the unit and can cause serious damage. -
Page 8: Dangers From Hot Surfaces
Katherm QE Assembly, installation and operating instructions Dangers from hot surfaces DANGER! Risk of fatal injury from hot surfaces This unit is hot when in operation. Do not touch the unit to prevent burns. Keep combustible materials, such as furniture, cushions, bedding, paper, clothing, curtains etc., away from the unit. The unit has hot and arc- ing or sparking components inside. -
Page 9: Personnel Requirements - Qualifications
Katherm QE Assembly, installation and operating instructions Personnel requirements - Qualifications Expertise The installation of this product requires expertise in heating, installation and electrical engineering, in compliance with na- tional regulations. As this knowledge is normally acquired through professional training in one of the above fields, it is not dealt with further here. -
Page 10: Transport, Storage And Packaging
IMPORTANT NOTE! Warranty claims can only be made within the applicable period for complaints. (More information is avail- able in the T&Cs on the Kampmann website) IMPORTANT NOTE! 2 people are needed to transport the unit. Wear personal protective clothing when transporting the unit. -
Page 11: Storage
Katherm QE Assembly, installation and operating instructions Storage Store packaging under the following conditions: Do not store outdoors. Store in a dry and dust-free place. Store in a frost-free place. Do not expose to aggressive media. Protect from direct sunlight. -
Page 12: Technical Data
29.2 stage Tab. 2: Technical data for Katherm QE The sound pressure level was calculated with an assumed room insulation of dB(A). This corresponds to a dis- tance of inches, a room volume of cft and a reverberation period of s. -
Page 13: Construction And Function
Brief description Katherm QE are decentralised units to heat room air, for use in hotels, offices and business premises, among others. Sec- ondary air is drawn in by the fan and passed through the electric heating coil. The temperature-controlled air rises up the... -
Page 14: Installation And Wiring
Katherm QE Assembly, installation and operating instructions Installation and wiring Requirements governing the installation site Only install and assemble the unit if the following conditions are met: Make sure that the unit is securely suspended/standing. Ensure that the airflow can circulate freely. -
Page 15: Installation Steps
Katherm QE Assembly, installation and operating instructions 6.2.1 Installation steps... - Page 16 Katherm QE Assembly, installation and operating instructions...
- Page 17 Katherm QE Assembly, installation and operating instructions...
- Page 18 Katherm QE Assembly, installation and operating instructions Separately packed roll-up grilles, for instance when using installation covers to protect the trenches from dirt, are rolled up in the factory. The grille can become slightly over-long due to the steel springs extending. Unrolling the grille and laying it flat for a few hours can return the grille to its original length.
-
Page 19: Screed Work
Katherm QE Assembly, installation and operating instructions 6.2.2 Screed work The following work steps must be completed before screed work: The electrical connection has been made correctly. The appliance is correctly positioned and aligned. There are no sound bridges to the bare concrete, especially in the area of the mounting aids. -
Page 20: Installation
Katherm QE Assembly, installation and operating instructions Installation 6.3.1 Connection to the pipe network Dimensions in mm Window side Room side Top view (without cover panel) Front view Side view Window side Room side Side view (cross-section enlarged) Top view (without cover panel) -
Page 21: Dimensions In Inches
Katherm QE Assembly, installation and operating instructions Dimensions in inches Window side Room side Top view (without cover panel) Front view Side view Window side Room side Side view (cross-section enlarged) Top view (without cover panel) 6.3.2 Fitting the grille High surface temperatures occur at the electric heating coil. - Page 22 Installation cover: Caution: Do not operate the Katherm QE or the electric heating coil with the installation cover in place. After removing the installation cover, position the grille and screw in place with the grille fixings and the self-tapping screws.
- Page 23 Katherm QE Assembly, installation and operating instructions...
-
Page 24: Electrical Connection
AWG 14 is also the largest wire gauge that can be connected to the terminals. Maximum electrical rating values Katherm QE, UL version (*UL, *U04, *U06) Length Nominal voltage [V... -
Page 25: Electromechanical Connection, 230 V (*00)
Electromechanical connection, 230 V (*00) Circuit description Katherm QE Katherm QE requires a 208 / 240 / 277 V AC power supply. The output of the electric heating coil and EC fan can be controlled continuously variably by a 0-10 V DC signal. - Page 26 DO1 with buzzer Setting the DIP switches LED status messages Terminal assignment X2 Terminal assignment X1 Fig. 3: Katherm QE PCB (only for 208 V and 240 V) DO1 with buzzer LED status messages Setting the DIP switches Terminal assignment X1 Terminal assignment X2 Fig. 4: Katherm QE 277 V PCB...
-
Page 27: Dip Switch Settings
Katherm QE Assembly, installation and operating instructions DIP switch settings Factory setting DIP 1 Enable not required Enable required DIP 2 Fan speed increase Off Fan speed increase On DIP 3 Minimum heat output = 20% Minimum heat output = 30%... -
Page 31: Pre-Commissioning Checks
Katherm QE Assembly, installation and operating instructions Pre-commissioning checks During initial commissioning, it must be ensured that all necessary requirements are met so that the appliance can function safely and as intended. Structural tests Check that the unit is securely standing and fixed. -
Page 32: Operation
2- and 4-pipe applications, surface- mounted wall installation on a flush-mounted box setpoint display by threshold arrows heating or cooling via active 0-10 V signals option for external room sensor connection digital input for ECO operation for use with Katherm QE, max. 5 units... -
Page 33: Maintenance
Katherm QE Assembly, installation and operating instructions Maintenance 10.1 Securing against reconnection DANGER! Risk of death by unauthorised or uncontrolled restart! Unauthorised or uncontrolled restarting of the equipment can result in serious injury or death. Before restarting, ensure that all safety devices are fitted and working properly and that there is no haz- ard to humans. -
Page 34: Faults
Katherm QE Assembly, installation and operating instructions Faults The following chapter describes possible causes of faults and the work needed to rectify them. Should faults occur frequently, shorten the maintenance intervals in line with the actual loading on the unit. - Page 35 Katherm QE Assembly, installation and operating instructions Table Tab. 1 Operating voltage ..............................6 Tab. 2 Technical data for ..............................12 Tab. 3 Maximum electrical connection values, electromechanical model ................. 24...
-
Page 36: Intertek Certificate Katherm Qe.pdf
This document is the property of Intertek Testing Services and is not transferable. The certification mark(s) may be applied only at the location of the Party Authorized To Apply Mark. Kampmann GmbH & Co. KG Kampmann GmbH & Co. KG... - Page 37 This document is the property of Intertek Testing Services and is not transferable. The certification mark(s) may be applied only at the location of the Party Authorized To Apply Mark. Kampmann GmbH & Co. KG Kampmann Polska Sp. z o.o...
- Page 40 Country Contact Kampmann Heating, Cooling, Ventilation Ltd. 1625 Dilworth Drive Unit #207 Kelowna, BC Canada V1Y 8M4 Canada T +1 604/ 3621080 F +1 604/ 6871327 E info@kampmann.ca W Kampmann.ca...
Need help?
Do you have a question about the Katherm QE and is the answer not in the manual?
Questions and answers