English Multifunctional Presentation Kit YP-100 Getting Started with the Multifunctional Presentation Kit • Be sure to read the “Safety Precautions” on page E-3 and “Operating Precautions” on page E-6 before trying to use this product. • This manual provides a general overview and covers basic operations of the YP-100. For more information about operations, see the User’s Guide on the bundled CD-ROM.
• CASIO COMPUTER CO., LTD. shall not be held liable for any loss or lost profits due to loss of data due to malfunction or maintenance of this product, or any other reason.
• Do not overload a power outlet. Unplug the AC Adaptor. Contact your original dealer or authorized CASIO service center. Misuse of the power cord creates the risk of personal injury, fire and electric Malfunction shock. Make sure that you always Never try to use the product while it observe the following precautions.
Doing adjustment, and repair up to your original so creates the risk of electric shock, dealer or authorized CASIO service center. burn injury, and other personal injury. Dropping and impact Be sure to leave all internal...
Safety Precautions Caution Caution AC adaptor Misuse of a battery can cause it to leak and stain the area around it, or to explode, Misuse of the AC adaptor creates the creating the risk of fire and personal injury. risk of fire and electric shock. Make Make sure that you always observe the sure that you always observe the following precaution.
Operating Precautions Operating Precautions This product is made of precision components. Failure to observe the following precautions can result in inability to correctly save data and malfunction. G Never use or store the product in the following locations. Doing so creates the risk of malfunction of and damage to the product.
The YP-100 makes it possible to connect a USB memory device, a wireless LAN, or a document camera to a data projector (CASIO XJ-S30, XJ-360, XJ-460) that is equipped with an RGB input terminal. Once you connect any one of the external USB devices described below to the USB terminal of the YP-100, you can project data from the connected device.
YP-100. XJ-S30, etc. YP-100 CASIO YW-2 You can have up to four computers connected to the YP-100 over a wireless LAN at the same time. Use the remote controller that comes with the YP-100 to select which of the four computer screens you want to project.
Introduction Using the YC-400 Document Camera with the YP-100 You can connect a CASIO YC-400 Document Camera to the USB port of the YP-100 and project the images of documents placed on the document stage of the YC-400. XJ-S30, etc.
Introduction About this manual... Terms and Conventions In this manual, there are many procedures that require parallel operations on the YP-100 and your computer. The following are special terms and conventions used in this manual to differentiate between the YP-100 and computer. projection area This is the entire rectangular area that is projected by the projector connected to the YP-100.
Introduction General Guide YP-100 LINE OUT terminal RGB OUT terminal AC adaptor terminal [POWER] indicator [ ] (Power) key Remote control signal receiver (both sides) [ ] (Hold) key [HOLD] indicator USB port Remote Controller Remote control signal emitter CLASS 1 LED PRODUCT [ ] key Cursor keys [ , [MENU] key...
Getting Ready Getting Ready Preparing the Remote Controller The remote control unit comes loaded with a test battery. Before using it for the first time, remove the battery insulation sheet from the back of the remote controller. To avoid running down the battery, store the remote control unit so its buttons are not pressed inadvertently.
Getting Ready Insert a new battery (CR2025) into the Slide the battery holder back into the battery holder. remote controller. Make sure that the plus (+) side of the battery is facing upwards (so you can see it). Connecting a Projector Make sure that the YP-100 and the projector are both turned off before connecting them.
Getting Ready Turning On Power To turn on the YP-100 Connect the projector to the YP-100, referring to “Connecting a Projector” (page E-13). Turn on the projector and/or audio equipment that is connected to the YP-100. Connect the AC adaptor that comes with the YP-100 to the AC adaptor terminal, and plug the AC adaptor into a power outlet.
Getting Ready To turn off the YP-100 Press the [ ] (Power) key to turn off the YP-100. Any changes you make to setup menu* settings are retained when you press the [ (Power) key to turn off the YP-100. Note, however, that setup menu settings are lost if you unplug the AC adaptor from the YP-100 without first pressing the [ ] (Power) key to turn it off.
Basic YP-100 Operations This section explains the following YP-100 operations. Basic YP-100 Operations Basic operation for using a USB memory device with the YP-100 You can use the projector connected to the YP-100 to project images from files stored on the USB memory device.
Basic YP-100 Operations 4. Enter “YP-100” and then press the [Enter] key. This will create a folder named “YP-100”. 5. Drag the image files to the “YP-100” folder. This will copy the image files into the folder. Be sure to copy only JPEG (jpg, jpeg or jpe) or BMP (bmp) format image files into the folder.
Basic YP-100 Operations Connect the projector to the YP-100, referring to “Connecting a Projector” (page E-13). Use the procedure under “Turning On Power” on page E-14 to turn on the YP-100. This will cause the YP-100’s [POWER] indicator to light green. The YP-100 logo screen also will be projected by the connected projector.
Basic YP-100 Operations Using the YP-100 with a YC-400 Document Camera Connect the projector to the YP-100, referring to “Connecting a Projector” (page E-13). Use the procedure under “Turning On Power” on page E-14 to turn on the YP-100. This will cause the YP-100’s [POWER] indicator to light green. The YP-100 logo screen also will be projected by the connected projector.
Basic YP-100 Operations With nothing on the document stage, press the [ ] (power) button on the camera stand. This will turn on the document camera. The YP-100 will recognize the document camera and start up the YC Camera application automatically.
Basic YP-100 Operations Place the document whose image you want to project onto the document camera’s document stage. Be sure to place the document in the center of the stage, and do not let any part of the document extend off the edges of the stage.
Specifications Specifications Model Name: YP-100 USB Port: USB TYPE A Stereo mini jack × 1 Audio Out Terminal: RGB mini D-Sub 15-pin × 1 RGB Out Terminal: Operating Temperature: 5 to 35°C (41 to 95°F) Operating Humidity: 20 to 80% (non-condensation) Power Requirements: 100 to 240 V AC, 50/60 Hz Rated Voltage:...