Advertisement
Advertisement
Table of Contents
Summary of Contents for AquaStar AquaRover AQR1601-H
- Page 1 INSTALLATION MANUAL...
- Page 2 CONTENTS FULL KIT INCLUDES CLEANER,SEVEN CONNECTOR HOSES, ONE LEADER HOSE, FLOW GAUGE, SKIMMER CONE, AND OWNER’S MANUAL. Skimmer Cone Flow Gauge Part # - HWN 152 Part # - HWN153 Leader Hose Part # -SZTHL Aqua Rover Cleaner Head Part # - AQR1601-H (Concrete) Connector Hoses (x7) Part # - AQRV1601-H (Vinyl/Fiberglass) Part # - SZTH...
-
Page 3: Important Notes
GPM (gallons per minute) of the suction line. It is designed to operate and install simply with most swimming pools. Occasionally, additional hoses and/or parts are needed to complete your special situation. For technical assistance and parts availability, call your local Aquastar Pool Products dealer. - Page 4 INSTALLATION STEP 1 Connect and submerge the hoses and cleaner Step 1a: Connect the cleaner (Fig. 1) There are seven connector hoses and one leader hose with a gray hose cuff. The hose cuff connects to the top of the Aqua Rover automatic pool cleaner.
- Page 5 INSTALLATION STEP 2 Connect Suction Source Step 2: Connect the skimmer to the suction source (two options available): Connector Hose Option A - Skimmer port Skimmer Cone The suction port of the skimmer, with skimmer cone and connector hose (see Fig. 4 ). Fig.
- Page 6 INSTALLATION STEP 4 Adjusting Cleaner For Best Performance Fig. 8 How to adjust cleaner tension The rear flap tension adjuster is preset to II. The tension adjustment controller is located in the rear of the unit (see Fig. 8). To adjust tension use a flat head screwdriver to rotate the tension controller. How to adjust if the cleaner is becoming trapped When the Aqua Rover automatic pool cleaner seems to be spending too much time against steps, vertical walls, and other obstructions, turn the rear flap tension adjuster to position I (see Fig.
-
Page 7: Cleaning Instructions
CLEANING Cleaning Instructions How to remove access cover and clear debris from the main turbine Should the Aqua Rover automatic pool cleaner stop moving or become sluggish due to debris trapped in the throat or inside the unit, the turbine/vacuum chamber is accessible following these instructions. - Page 8 SERVICE Shoe Replacement How to check the condition of the shoes The pod shoes and wings have wear indicators on their sides and should occasionally be checked to determine if replacement is needed. The shoe wear indicator is a line on the side of the pod shoe that appears as a difference in texture.
- Page 9 SERVICE Pod Replacement How to tell if the pods need to be replaced The pod is the walking leg of the unit that holds both Wing the pods shoes and wing (see Fig. 16). If the cleaner’s pods are worn the cleaner may experience slow or no forward movement.
-
Page 10: Flap Replacement
SERVICE Flap Replacement How to tell if the flaps need to be replaced The flaps help allow the cleaner to climb walls and can be adjusted (See Pg. 6 Step 4 ). If the flaps are worn the cleaner may experience trouble climbing vertical walls or may float up from the floor. How to remove the flaps Remove the front and rear flaps from your Aqua Rover automatic pool cleaner by inserting a small screwdriver between the flap and the lower body near the pivot point of the flaps (see Fig. -
Page 11: Bumper Replacement
SERVICE Bumper Replacement How to tell if the bumber needs to be replaced If the bumber show signs of major wear it should be replaced. A hole or crack on the bumber can cause problems with the cleaner's operation. Replacing the bumper is not recommended to be repaired by beginners Pro Tip Replacement of the Aqua Rover automatic pool cleaner bumper is not recommended as a “do it yourself”... -
Page 12: Troubleshooting
Problem: Cleaner fails to climb vertical walls gunite/concrete pool CAUSES SOLUTIONS Improper shoes for application Contact your local Aquastar Pool Products dealer Lack of/improper water flow through cleaner Adjust water flow, Pg. 5 -6 Partial obstruction of Aqua Rover throat Clear obstruction, Pg. - Page 13 TROUBLESHOOTING Problem: Cleaner climbs to the surface and sucks air CAUSES SOLUTIONS Too much/improper water flow through cleaner Adjust water flow, Pg. 5-6 Improper tension on rear flap Turn rear flap adjuster to I If still climbing too much, reduce water flow until the proper operation is achieved, Pg.
- Page 14 To better serve you, please have the following information D. The integrity of “good” pool plaster is such that the available if you contact your local Aquastar Pool Products plaster will cause wear on the Aqua Rover automatic dealer.
-
Page 15: Warranty
Aquastar Pool Products warrants this cleaner to be free from act of God, abuse, misuse, negligence, omissions. defects in materials and workmanship for a period of one year from the original date of purchase subject to all the following 6. - Page 16 10. Spindle Gear Screw - HWN125 selection of these dependable 11. Float Kit, 2 Pack - HWN136 Aquastar Pool Products 12. Middle Body Screw, 6 Pack - HWN139 13. Upper Body Screw, 6 Pack - HWN130 replacement parts. Each one 14.
- Page 17 PROSTAR REPLACEMENT KITS We’ve made your pool equipment service and repair a lot easier with these convenient replacement kits. Each one is a complete grouping that contains everything you need for that particular repair. For more information or to stock up on individual replacement parts at prostarreplacementparts.com or call 877-768-2717.
- Page 18 PROSTAR REPLACEMENT KITS We’ve made your pool equipment service and repair a lot easier with these convenient replacement kits. Each one is a complete grouping that contains everything you need for that particular repair. For more information or to stock up on individual replacement parts at prostarreplacementparts.com or call 877-768-2717.
- Page 20 AUTOMATIC SUCTION POOL CLEANER Please fill out warranty information on reverse side and mail to: AquaStar Pool Products, inc. Warranty Registration Dept. 104 2340 Palma Drive Ventura, CA 93003 Don’t forget to include a copy of your receipt as proof of purchase...
Need help?
Do you have a question about the AquaRover AQR1601-H and is the answer not in the manual?
Questions and answers