1. Manuals
  2. Brands
  3. Proton Manuals
  4. Industrial Equipment
  5. InteliSENS PD30XY
  6. Instruction manual

Proton InteliSENS PD30XY Instruction Manual

Dual axis laser scanning diameter gauge
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual
InteliSENS PD30XY Dual Axis Laser Scanning
Diameter Gauge
Issue 1a
10 November 2020
Proton Products Co. Ltd.
10 Aylesbury End
Beaconsfield
Buckinghamshire HP9 1LW
England
www.protonproducts.com
Page 1 of 71
Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the InteliSENS PD30XY and is the answer not in the manual?

Questions and answers

Related Manuals for Proton InteliSENS PD30XY

Summary of Contents for Proton InteliSENS PD30XY

  • Page 1 Instruction Manual InteliSENS PD30XY Dual Axis Laser Scanning Diameter Gauge Issue 1a 10 November 2020 Proton Products Co. Ltd. 10 Aylesbury End Beaconsfield Buckinghamshire HP9 1LW England www.protonproducts.com Page 1 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 2: Table Of Contents

    NFORMATION ..............................38 TORE ............................38 TATISTICS FFT ..............................39 ACCESS LEVELS ..........................40 ..........41 TANDARD OMMUNICATIONS NTERFACES CAN- ....................... 41 BUS COMMUNICATIONS CAN-bus interface ............................41 Page 2 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 3 Reading a block of output parameters ......................59 Reading a continuous stream of a single output parameter ............... 59 Reading a continuous stream of a block of output parameters ..............60 Page 3 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 4 ......71 ONTACT DETAILS FOR ENQUIRIES SALES AND SERVICE ............................71 EB SITE ......................... 71 NQUIRIES AND SALES ..........................71 ERVICE ENQUIRIES ............71 ANUAL FEEDBACK AND COPYRIGHT Page 4 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 5: Declaration Of Conformity (Ce)

    (CE) ECLARATION OF ONFORMITY Proton Products International Limited declares that the equipment listed below fulfils the requirements of directive EMC: 2014/30/EU and Low Voltage: 2014/35/EU. The following standards were applied: Radio -⁠ ETSI EN 300 328 V2.1.1 (2016-⁠ 1 1)

  • Page 6: Introduction

    When fitted with the optional CDI4 interface display unit, the InteliSENS PD30XY diameter gauge can operate as a standalone unit. RS-232, RS-422, RS-485 and Ethernet communication interfaces are installed as standard for straightforward connection to computers or PLCs.

  • Page 7: Specifications

    RS-232*, RS-422, RS-485, CAN-bus**, Ethernet *An optional RS-232-to-USB converter cable is available for connection to USB equipped computers. **CAN-bus protocol is proprietary and reserved for connection to other Proton Products equipment such as a CDI4 interface display unit. Page 7 of 71...

  • Page 8: Ptional Interfaces

    Statistical Process Control automatic set point for PI feedback controller (requires PI feedback controller option) Fast Fourier Transform analysis for amplitude and frequency of periodic diameter variations SMFD Single Measurement Flaw Detection (Lump and Neck detection) Page 8 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 9: Dimensional Drawings

    IMENSIONAL RAWINGS Page 9 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 10: Annotated Drawings

    CAN-bus communications interface and DC power input Air wipe air inlet RS-232, RS-422/485 communications interface Logic and speed pulse inputs, relay outputs, optional analogue input, optional PI feedback controller I/O Gauge head mounting holes Page 10 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 11: Optional Accessories

    For connecting a RJ45 8P8C terminated network cable to the DB9 industrial bus port.  Comes as a pair for connecting to either type A or type B terminated network cables. Proton part number 00041MC048 Page 11 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 12: Electrical Interfaces

    Requires the PI feedback controller interface option (00047MC061) to be installed. Proton part number 00054SW011 Single Measurement Flaw Detection (SMFD)  High-speed lump and neck flaw detection. Proton part number 00054SW014 Page 12 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 13: Interface Display Modules

    End user cables are sealed with three cable glands.  Input voltage range: 90 – 260 VAC @ 45 – 65 Hz.  Select the required length of DB25 cable from below. Proton part number 00047MC660 Page 13 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 14 Select the required length of DB25 cable from below. Proton part number 00041MC730 DB25 “INTERFACE” port to PSU-BOB-DG, Terminal Strip-DIN cable Length / m Proton part number 00041CT003 00041CT005 00041CT010 00041CT020 00041CT030 Page 14 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 15: Installation

    Measured objects threaded through the optical gate cavity must be secured against contact with the optical windows or catching upon the gauge body. For cable production line applications, Proton Products can supply optional adjustable cable guides for securing the passage of a cable through the optical gate cavity.

  • Page 16: Optical Window Cleaning Procedure

    NSTALLATION SEQUENCE Unpack the gauge and check for missing accessories and shipping damage. Mechanical installation: 1. Mount the gauge securely on a user supplied mount or on an optional Proton Products height stand. Electrical installation: 1. Install earth connections.

  • Page 17: Mechanical Installation

    Ensure that the cable alignment is perpendicular to the face of the gauge with the least error practically possible, an angle error of one degree gives a measurement error of 0.013%, at two degrees this becomes 0.05%. Page 17 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 18: Electrical Installation

    CAN-bus extension cable.  The remote CDI4 interface display unit can also power DC powered gauges through a CAN- bus port connected power supply. Page 18 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 19 1. Connect the remote CDI4 interface display unit to the CAN/POWER connector using a CAN- bus extension cable. 2. Connect an optional PSU-CAN mains power supply unit to the second CAN-bus port on the remote CDI4 interface display unit. Page 19 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 20: Dc Power Supply

    Description Notes REG.GND Power supply ground (0 V) +24V +24 V power supply Ensure that the cable shield is connected to this Shield via the plug shield connection. Page 20 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 21: Powering On The Gauge

    Powering off the gauge The gauge has no power switch; it may be powered off by switching off or disconnecting the power supply to the unit. Page 21 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 22: Configuration Via Cdi4

    CDI4 ONFIGURATION VIA Power on screen When the gauge is powered on, the Proton welcome screen will be displayed momentarily. Touch screen calibration The CDI4 touch screen can be calibrated using the following procedure. 1. Press the “Click to calibrate touch screen” message during gauge power on to access the screen calibration function.

  • Page 23: Home

    - Measured Y diameter (time averaged). - Y error (Y diameter – Preset Y diameter) Press the button to access the function menu page. button to advance to “Home Page 3”. Press the Page 23 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 24: Home

    - Position of last neck flaw - Neck flaw count Press the button to access the function menu page. button to advance to “Home Page 5”. Press the Page 24 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 25: Home

    - Calculated cumulative length of object Press the button to reset length to zero. Press the button to access the function menu page. button to return to “Home Page 1”. Press the Page 25 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 26: Function Menus

    Press the button to access the function menu page. Press the button to advance to the next page. Page 26 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a) Press the button to return to the home page.
  • Page 27 (depending on the setting for “SMFD tol mode” above. Press the button to return to the home page. Press the button to access the function menu page. Press the button to advance to the next page. Page 27 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 28  SMFD (Single Scan Flaw Detection) is NOT available in “Helix” mode. Units: Metric; Imperial Metric: Millimetre (mm) and metre (m) measurement units. Imperial: Inch (in) and feet (ft) measurement units. Page 28 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 29 If the “Reference Average Time” is set to too short a duration (i.e. close to the time duration of the flaws), then the flaws will significantly affect the value of the “Reference Diameter” and may result in the detection of false flaws. Page 29 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 30: Start Speed

    Setting a minimum “Start speed” prevents the SMFD function from logging flaws during line start-up and shutdown. Start length Setting a minimum “Length” prevents the SMFD function from logging flaws during line start-up and shutdown. Page 30 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 31 Do not forget to set to “OFF” to exit simulation mode and resume normal measurement operation. Dia compensation All measured diameter values are multiplied by this “Diameter Compensation” factor before display or reading through a communications interface. Page 31 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 32: Communications

    - Set the Interval time of UDP. Press the button to return to the home page. Press the button to access the function menu page. Press the button to advance to the next page. Page 32 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 33 - Enter the gateway IP address of the network. Press the button to return to the home page. Press the button to access the function menu page. Press the button to advance to the next page. Page 33 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 34: Interface

     For bipolar outputs, the most negative measured error corresponds to a -10V output voltage. AOP response: Instant; Average. Instant: Analogue output voltage represents the value of each individual measurement. Average: Analogue output voltage represents the time averaged measured value. Page 34 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 35 Over average (upper limit); Under average (lower limit); Over X (upper limit); Under X (lower limit); Over Y (upper limit); Under Y (lower limit); Over ovality (upper limit); Window Dirty. Page 35 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 36: Speed Source

    Preset: Use the fixed “Preset speed” value for the line speed. Pulse: Determine the line speed from the pulse input. Analogue: Determine the line speed from the analogue input voltage. Page 36 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 37: Gauge Information

    - Gauge firmware issue date. - CDI4 software version. - CDI4 software issue date. Press the button to return to the home page. Press the button to access the function menu page. Page 37 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 38: Store

    - Count down of the remaining statistics time or length until the next statistics result. Press the button to return to the home page. Press the button to access the function menu page. Page 38 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 39: Fft

    - FFT peak value. - FFT sampling window remaining time. Press the button to return to the home page. Press the button to access the function menu page. Page 39 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 40: Access Levels

    The Home pages 2, 3, 4, 5 can be set to be displayed or hidden by selecting “TRUE” or “FALSE”. It is necessary to unlock the relevant pages before their parameters can be set via the CDI4 interface. Page 40 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 41: Standard Communications Interfaces

    This CAN-bus interface is fitted as standard. It operates independently of the other communications interfaces and may be accessed at the same time as them. The CAN-bus interface uses a proprietary Proton Products protocol. It is exclusively used to communicate between the unit and other Proton Products modules. The unit automatically detects connection to other modules and configures the bus appropriately;...

  • Page 42: Rs-232 Communications

    RS-232 interface. The SLP RS-232 data format is: Number of data bits Parity Number of stop bits Flow control Default baud rate None None 115200 bit / s Page 42 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 43: Rs-422 / Rs-485 Communications

    Connector type: RJ45 8P8C female (socket) Designation Comments LAN TX+ LAN TX- LAN RX+ LAN RX- Shield Ensure that the cable shield is connected to this via the plug shield connection. Page 43 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 44: Ethernet Led Indicator

    The PROFIBUS interface may be accessed through the “PROFI/EIP/DEV” connector. Connector type: DB9 female (socket) PROFIBUS Comments Shield Ensure that the cable shield is connected to this via the plug shield connection. Page 44 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 45: Profibus Led Indicator

    Ensure that the cable shield is connected to this via the plug shield connection. PROFINET LED indicator LED status Indication i-BUS Continuous green Online PROFINET communications Continuous red Communication error Extinguished No communication Page 45 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 46: Ether Net / Ip Communications

    Ensure that the cable shield is connected to this via the plug shield connection. EtherNet / IP LED indicator LED status Indication i-BUS Continuous green Online EtherNet / IP communications Continuous red Communication error Extinguished No communication Page 46 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 47: Standard Electrical Interfaces

    LECTRICAL NTERFACES PEED PULSE INPUT The speed pulse input may be connected to a line speed gauge (such as a Proton Products SL or SLR series non-contact laser speed and length gauge). Measured line speed input is required for: ...

  • Page 48: Analogue Input

    The analogue input and its ground reference are isolated from earth. Specification Minimum Typical Maximum Units Input voltage measurement range Input voltage absolute range Input-to-earth voltage kΩ Input resistance Page 48 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 49: Logic Inputs

     For 24V signals (such as from a PLC), the power dissipation in the 820Ω resistor can be reduced by connecting another 820Ω in series between the pull-up signal source and logic input. Page 49 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 50: Logic Inputs Configuration

    Comments Units Range/Remark 0=OK No reading 1=No Reading 0=OK No object 1=No Object 0=OK Lens dirty 1=Lens Dirty 0=OK Line speed too low for helix mode 1=Too Low Page 50 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 51 0=OK Line speed too high for helix mode 1=Too High 0=OK Gauge overheat 1=Gauge overheat 0=OK External alarm 1 1=Alarm 0=OK External alarm 2 1=Alarm Page 51 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 52: Relay Outputs

    If the relay contacts are used to switch inductive loads, then suppressors must be fitted to clamp voltage spikes. Specification Minimum Typical Maximum Units DC voltage between contacts Contact-to-earth voltage Current Ω On resistance (at a current of 10mA) Page 52 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 53: Optional Electrical Interfaces

    Analogue outputs and their shared ground reference are isolated from earth.  Analogue outputs are short circuit proof. Specification Minimum Typical Maximum Units Output voltage Output-to-earth voltage kΩ Load resistance Page 53 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 54: Pi Feedback Controller

    PIN input to earth voltage kΩ PIN input impedance POUT output voltage POUT output voltage (absolute forced) POUT output to earth voltage POUT output current Ω POUT output impedance Page 54 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 55: Pi Feedback Controller Connection To Production Equipment

    In this configuration, the PI feedback controller output voltage is added to a fixed control voltage from a potentiometer or PLC via the auxiliary control input on the extruder or capstan driver. The fixed Page 55 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 56 The system cannot function if R2 > 5  R1 since the maximum control range will be < 10%, which is normally not sufficient. Page 56 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 57: Interface Connector Pin Outs

    Low < +3 V; High > +10.5 LIN1 Logic inputs Logic input 1 V; Max ±30V REG.GND Power supply Power supply ground (0 V) +24V Power supply +24 V power supply Shield Page 57 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 58: Proton Standard Parameter Access Protocol

    Use the following request format to read a contiguous block of input parameter values: Request ?[Input parameter number][Space][Number of parameters]<CR><LF> format Response [Input parameter value]<CR><LF> format Only consecutive parameter values may be requested in a block parameter request. Page 58 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 59: Writing Input Parameters

    For a data transfer rate of 1200 bit / s and a data length of seven 8-bit characters per parameter value, approximately 10 individual parameter values can be transferred per second. Page 59 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 60: Reading A Continuous Stream Of A Block Of Output Parameters

    The data stream can be terminated by sending an escape character to the gauge (ASCII code decimal 27 or the ‘Esc’ key or the ‘Ctrl’’[‘ key combination on a PC keyboard). Page 60 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 61 ODBUS PARAMETER ACCESS PROTOCOL This protocol provides access to individual parameters or blocks of parameters and is typically used in a production environment where the Proton Products instrument is connected to a computer, Modbus connected PLC or similar device. The parameters consist of 16-bit words (DW) and are divided into input and output groups: ...

  • Page 62: Input Parameters

    50000 DW19 DW20 Preset Y upper limit 1=0.01um/0.01mil 0~20000000 50000 DW21 DW22 Preset Y lower limit 1=0.01um/0.01mil 0~20000000 50000 DW23 DW24 Preset Z upper limit 1=0.01um/0.01mil 0~20000000 50000 Page 62 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 63 The polarity of logic input 1 high 0=Active low; 1=Active The polarity of logic input 2 high Relays 0=Gauge OK;1=Over all limit; 2=Under all DW50 Relay 1 function limit;3=Flaw;4=Lump;5 =Neck, 6=Over Average Upper Page 63 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 64 1=1% 0~100 DW62 P gain 1=1% 0~100 Analogue O/P Analogue O/P 1 0=Average ;1=X;2=Y;3 =Z;4=Ovality;5=Averag DW63 e error;6=X error;7=Y error;8=Z error;9=Ovaity error; Analogue O/P 2 Analogue O/P 3 Page 64 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 65 DW84 CAN BUS baud rate ther=500 0=4800;1=9600;2=192 DW85 RS232 baud rate 00;3=38400;4=115200 0=Modbus;1=Proton;2= DW86 RS232 protocol SLP;3=Print 0=Modbus;1=Proton;2= DW87 RS422/RS485 protocol 0=4800;1=9600;2=192 DW88 RS422/RS485 baud rate 00;3=38400;4=115200; 5=250K;6=500K;7=1M Page 65 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 66 DW119 Zero of analogue O/P1 DW120 Gain of analogue O/P2 10000 DW121 Zero of analogue O/P2 DW122 Gain of analogue O/P3 10000 DW123 Zero of analogue O/P3 DW124 Page 66 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 67 Zero of analogue input DW127 Parameter Group Number 1~50; 0 is not used 1=Load parameters from specified DW128 Parameter Group Control group;2=Save current parameters to specified group DW129 Page 67 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 68: Output Parameters

    External Alarm 1 0=OK,1=Alarm External Alarm 2 0=OK,1=Alarm Average diameter/Envelop 1=0.01um{mil} 0~20000000 X diameter 1=0.01um{mil} 0~20000000 Y diameter 1=0.01um{mil} 0~20000000 Z diameter 1=0.01um{mil} 0~20000000 DW10 Ovality 1=0.01um{mil} 0~20000000 Page 68 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 69 -32768~32767 DW42 Length 1=0.001m{1=0.001ft} DW43 Statistics Normal distribution 0=No;1=Yes DW44 Not used SPC is available 0=No;1=Yes DW45 Statistics remain time 1=1s{1=1m{ft}} 0~65535 DW46 Standard deviation 1=0.01um{mil} 0~20000000 DW47 Page 69 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)
  • Page 70 DW64 IP address for ETH xx.xx.xx.xx DW65 DW66 IP address for iBUS xx.xx.xx.xx DW67 DW68 Sub net Mask xx.xx.xx.xx DW69 DW70 Gateway xx.xx.xx.xx DW71 DW72 Gauge temperature 1=0.1℃ Page 70 of 71 Proton Products InteliSENS PD30XY Instruction Manual (Issue 1a)

  • Page 71: Sales And Service

    Proton Products is not responsible for consequential or incidental damage related to the provision or use of the information contained in this manual.  The information contained in this manual is the property of Proton Products and may not be circulated or distributed to third parties. ...

Table of Contents