Summary of Contents for Adele Aero Aqua-X
- Page 1 Adele Aero Quadcopter Aqua-X Small-sized, FPV drone with detachable arms Assembly and Operation Manual AAQX.000.000 Revision 1.0 from 05/14/24...
-
Page 2: General Information
General information Aqua-X is a universal FPV quadcopter for propellers from 7 to 11 inches. Its main payload is a rotating servo gimbal for any 19x19mm FPV camera. Recommended video system: DJI FPV with Polar/Nebula Pro/O3 cameras, Walksnail Avatar. The main advantages of Aqua X are high strength, compact design with detached arms and flexible layout. -
Page 3: Assembly Recommendations
Assembly Recommendations Security measures: 1. Work with glue and activator in a well-ventilated area. 2. Do not leave parts or the assembled aircraft in direct sunlight or in rooms with temperatures above 40 degrees for a long time without cooling. 3. -
Page 4: Printing Options
Printing options We strongly recommend following the instructions to achieve the best results. The model is designed for a printing area of 220x220x200 mm You need to configure print profiles: Dense parts made of ABS (PLA+, PETG) with filling. These are power elements: motor mounts, racks, suspension, etc. - Page 5 List of Printed Parts Parts marked as “mirror” will be reflected in the slicer according to quantity. The total weight of all parts is approximately 120 grams.
- Page 6 Location of parts on the printing bed An example of the location and orientation of parts. Supports must be turned off.
- Page 7 General view of the model The main assembly units in the archive with files are located in separate folders Body AAQX.001.Body Tilt camera AAQX.003.Gimbal AAQX.002.Arm...
-
Page 8: Мт30
It is necessary to assemble two right and two left beams. Part AAQX.002.Mt30Clamp print 2 pcs regular + 2 pcs mirror Propeller Gemfan 7042 Nut comes with the motor М5 Motor 2807 1300 kv When assembling, rest the flat surfaces on the table for leveling. -
Page 9: Self-Tapping Screw
Tilt camera Screws comes with servo Servo GH-s37d (Es9051/52) Self-tapping screw 2,2х4,5 Screw М2х6 Screw M2x8 Do not tighten it all the way! Hardware Screws: М2х6 - 4 шт М2х8- 1 шт Self-tapping screw : 2,2х4,5... -
Page 10: Table Of Contents
Body 1 Bracket Self-tapping screw Мт30 (4) 2,9х19 МТ30 male Fan 2510 mark down Screws М2х12 Self-tapping Video transmitter screw Self-tapping Place for 2,2х6,5 screw suspension wires 2,2х6,5 GPS Matek M10 glued to foam tape FC SpeedyBee f405 stack Self-tapping screw 2,2х6,5 for USB VTX... -
Page 11: Self-Tapping Screw 2,2Х6,5
Body 2 The antenna of the video transmitter insert into the hole covers up to the stop Bolt М3х30 AAQX.001.Knob AAQX.001.GPSCover AAQX.001.Visor Screws 2,2х9,5 AAQX.001.Cover AAQX.001.BodyTop Hardware Bolts: М3х30 - 4 pcs Self-tapping Self-tapping screws screw: 2,2х6,5 2,2х6,5 3 pcs 2,2х9,5 - 4 pcs... -
Page 12: Hardware
Body 3 Саморезы 2,9х16 2 шт Self-tapping screws 2,9х19 Foam patch lining for the battery, Hardware dimensions 5x60x120 mm Self-tapping screws: 2,9х16 - 2 pcs 2,9х19 - 8 pcs... - Page 13 General assembly Right arm (2) Left arm (1) Body Left arm (3) A (1 : 1) Right arm (4) The number of the arm Attach the 6s1p battery with a strap...
- Page 14 Views of the Model...
-
Page 15: Maintenance
Maintenance Aqua-X does not require time-consuming special maintenance. It is only necessary to inspect the device for damage every time during pre-flight and post-flight. Pay special attention to the propellers, arm connections, connectors and camera. It is forbidden to fly with damaged propellers and/or power elements of the hull.
Need help?
Do you have a question about the Aqua-X and is the answer not in the manual?
Questions and answers