Sealey CP20VNR Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Wear eye
Refer to
instructions protection
1. SAFETY
1.1. GENERAL SAFETY
WARNING!- Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all
9
instructions listed below may result in electric shock, fire and/or serious injury.
Save all warning and instructions for future reference.
9
Keep work area clean and well lit. Cluttered or dark area invites accidents.
9
DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools
8
create sparks which may ignite the dust or fumes.
Keep children, bystanders and pets away whilst operating a power tool. Distractions can cause you to lose control.
9
Stay alert, watch what you are doing and use common sense when operating a power tool.
9
DO NOT use a power tool whilst you are tired or under the influence of drugs, alcohol, or medication. A moment inattention whilst
8
operating power tools may result in serious injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes,
9
hard hat or hearing protection use for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack,
9
picking up or carrying the tool. Carrying power tools with your fingers on the switch or energising power tools that have the switch
on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the
9
power tool may result in personal injury.
Remove battery pack from the tool before making any adjustments, changing accessories, or storing power tools.
9
DO NOT overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected
8
situations.
DO NOT wear loose clothing, jewellery and dress properly. Keep your hair and clothing away from moving parts. Loose clothes,
8
jewellery or long hair can be caught in moving parts.
DO NOT let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A
8
careless action can cause severe injury within a fraction of a second.
DO NOT force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer
8
at the rate for which it was designed.
DO NOT use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is
8
dangerous and must be repaired.
Store idle power tools out of the reach of children and DO NOT allow persons unfamiliar with these power tools or these
9
instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Have your power tool serviced by a qualified repair person using only identical replacement
9
parts. This will ensure the safety of the power tool is maintained. Check for misalignment or biding of the moving parts, breakage of
parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
9
Use the power tool, accessories and tool bits etc, in accordance with these instructions, taking into account the working conditions
9
and the work to be performed. Use of the power tool for operations different from those intended could results in a hazardous
situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces DO NOT
9
allow for safe handling and control of the tool in unexpected situation.
Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring.
9
Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator
an electric shock
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased
9
risk of electric shock if your body is earthed or grounded.
DO NOT expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
8
© Jack Sealey Limited
20V SV20 BRUSHLESS CORDLESS NUT
RIVETER - BODY ONLY
MODEL NO:
Wear safety Wear ear
footwear protection
Original Language Version
CP20VNR
CP20VNR Issue 1 21/11/23