Do you have a question about the 3062 and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for TSI Instruments 3062
Page 1
P a r t i c l e I n s t r u m e n t s Model 3062 Diffusion Dryer Instruction Manual P/N 1933062, Revision G September 2003...
Page 2
M a n u a l H i s t o r y The following is a manual history of the Model 3062 Diffusion Dryer Instruction Manual, P/N 1933062. Revision Date Final November 1987 September 1989 January 1992 August 1994...
Page 3
If any malfunction is discovered, please contact your nearest sales office or representative, or call TSI at 1-800-874-2811 (USA) or (651) 490-2811. Model 3062 Diffusion Dryer...
For Customer Service..............8 Specifications................9 F i g u r e s 1 Model 3062 Diffusion Dryer ............1 2 Schematic of Desiccant Dryer Tube..........4 3 Installing the Filling Jig on the Inlet........... 7 Model 3062 Diffusion Dryer...
Page 6
T a b l e s 1 Packing List for the Model 3062 Diffusion Dryer ....... 2 2 Drying Capacity of the Dryer ............. 5 3 Specifications of the Model 3062 Diffusion Dryer ...... 9 Model 3062 Diffusion Dryer...
A b o u t T h i s M a n u a l This manual contains instructions for using and maintaining the Model 3062 Diffusion Dryer. The manual is organized into the following sections: ❑ Introduction ❑ Unpacking ❑...
Page 9
D i f f u s i o n D r y e r I n t r o d u c t i o n The Model 3062 Diffusion Dryer is designed as a general-purpose aerosol dryer that has minimal aerosol loss. The aerosol inlet incorporates a water trap that collects coarse water droplets.
Page 10
U n p a c k i n g The Diffusion Dryer consists of a diffusion dryer tube with water trap and fittings attached and accessories, including the following: Table 1 Packing List for the Model 3062 Diffusion Dryer Qty. Item TSI Part No.
Desiccant Dryer The Model 3062 Diffusion Dryer is a general-purpose aerosol dryer consisting of two concentric cylinders (see Figure 2). The inner cylinder is made of wire screen and the outer cylinder is made of Plexiglas.
(see next section) and bake it in a pan in an oven at 250°F [120°C] until the blue color returns. If the blue color does not return, the silica gel is no longer usable and must be replaced. Model 3062 Diffusion Dryer...
Humidity at Exit (%) No diffusion dryer With one Model 3062 With two Model 3062s (in series) With one Model 3062 but after one hour of operation After shaking the Model 3062 to rearrange the silica gel crystals Removing the Silica Gel To remove the silica gel, do the following: 1.
7. Make sure that the end cap is completely threaded in place. 8. Replace the dryer into its holding cradles and reattach the fittings to the inlet and outlet. Model 3062 Diffusion Dryer...
❑ A billing address ❑ A shipping address. Use the original packing material to return the Model 3062 to TSI. If you no longer have the original packing material, use sufficient packing material so the instrument is not damaged during shipping.
Page 17
S p e c i f i c a t i o n s The following specifications—which are subject to change—describe the most important data of the instrument’s major components. Table 3 Specifications of the Model 3062 Diffusion Dryer Flowrate 0 to 4 L/min 415 kPa (60 psig)
Page 19
Please help us improve our manuals by completing and returning this questionnaire to the address listed in the “About This Manual” section. Feel free to attach a separate sheet of comments. Manual Title Model 3062 Diffusion Dryer P/N 1933062 Rev. G 1.
Need help?
Do you have a question about the 3062 and is the answer not in the manual?
Questions and answers