Advertisement
Advertisement
Table of Contents
Summary of Contents for Flybox CAN-BRIDGE
- Page 1 ® CAN-BRIDGE For Rotax i-Series Engines ®...
- Page 2 Installation and User Manual, Safety Instructions and Warning Booklet This product is not TSO’d and cannot be installed into traditional FAA Part 23 and similarly Type-Certificate Aircraft ROTAX® is the registered trademark of BRP-Rotax GmbH & Co Document A2019 CAN-BRIDGE Revision#1.0, 18/01/2019...
- Page 3 CAUTION: Used to warn the user and indicate a potentially hazardous situation or improper use of the product. WARNING: Used to indicate a dangerous situation that can cause personal injury or death if the instruction is disregarded. CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet...
- Page 4 WARNING: It is the pilot’s responsibility to test this device before operating the aircraft and to make sure nobody is using it unless properly instructed and authorized to do so. CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet...
- Page 5 FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. WARNING: Alterations, additions, or repairs not performed by the instrument manufacturer or by a person or organization authorized by the manufacturer shall negate any warranty. CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet...
- Page 6 Installation and user Manual, Safety Instructions and Warning Booklet, do not install this device in his aircraft. NOTE: Flybox Avionics reserves the right to change or improve its products as well as terms, conditions, and notices under which their products are offered without prior notice.
- Page 7 CAN-BRIDGE reads the signals of the 2 CAN buses keeping them physically separate and sends all the informations to the engine instruments that have only one CAN input. This avoids to lose all the informations in case of malfunction or short circuit of one of the 2 CAN buses, respecting Rotax®...
-
Page 8: Mechanical Installation
FLYBOX ® Mechanical installation Mechanical Installation Install the CAN-BRIDGE in a dry environment following the mechanical instructions below. CAUTION: Do not expose the device to temperatures higher than 70°C. Do not expose the CAN-BRIDGE to water. CAN-BRIDGE Installation and User Manual,... -
Page 9: Electrical Installation
CANBUS2 (connect to pin 13 to activate it) Input CAN2_H (From Rotax® ECU B) 120 OHM resistive termination for CANBUS3 (connect to pin 15 to activate it) Output CAN3_H table continue on the next page >> CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet... - Page 10 120 ohm resistor, that in the case of CAN- BRIDGE are integrated inside the instruments so that the installer should simply connect together two pins on the connector to perform the required terminations. CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet...
- Page 11 1 mS, 30 V, which is generated with a frequency proportional to the RPM read on the CAN- bus. Jumpers enable the relevant terminating resistors. Comply with the standards for CAN bus line terminations. CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet...
-
Page 12: Technical Specifications
● Humidity: 90% max (without condensation). WARNING: A power supply exceeding the limits indicated or voltage peaks that exceed the limits may cause malfunction or permanent damage to the device. CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet... -
Page 13: Warranty
Products is not intended to be used. Flybox Avionics, after verification of the complaint and confirmation that the defect is covered by warranty, at its sole discretion, will either replace or repair the Products at no costs for the customer. - Page 14 Use of this product is unauthorized in any jurisdiction that does not give effect to all provisions of these terms and conditions, including without limitation this paragraph. CAN-BRIDGE Installation and User Manual, Safety Instructions and Warning Booklet...
- Page 15 First release WARNING: All photos, data, drawings, instruments layouts, technical solutions and data representation you find in this document or watching at FLYBOX® instruments working and/or you can access by means of any other media, including web sites, are sole property of MICROEL s.r.l., cannot be copied or imitate without a written permission of MICROEL...
- Page 16 Via G. Marconi 33/35 25080 Carzago di Calvagnese della Riviera (BS) - Italy Tel. +39 (0) 30601033 - Fax +39 (0) 30601463 www.sorlini.com Flybox® is a registred brand of Microel s.r.l.- Italy www.flyboxavionics.it Via Mortara 192-194 27038 Robbio (PV) - ITALY Tel +39 (0) 384670602 - Fax +39 (0) 384671830 www.flyboxavionics.it...
Need help?
Do you have a question about the CAN-BRIDGE and is the answer not in the manual?
Questions and answers