Table of Contents
Advertisement
Quick Links
ERF1002_EVB, Extreme Low Power Bluetooth 5.0 SoC Module
___________________________________________________________
_________________________________________________________________________________________________
www.summit-electronics.com
info@summit-electronics.com
Quick Start Guide
ERF1002_EVB
rev. -1-
Subject to change
without notice
Page 1 of 10
Advertisement
Table of Contents
Summary of Contents for Summit ERF1002 EVB
- Page 1 Quick Start Guide ERF1002_EVB ERF1002_EVB, Extreme Low Power Bluetooth 5.0 SoC Module ___________________________________________________________ _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change without notice Page 1 of 10...
-
Page 2: Document Information
Revision and date R1.0 01-02-2022 Product status (MP) Mass Production This document applies to the following products: Name Type number version Product status ERF1002_EVB ERF1002_EVB MP (Mass Production) _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change without notice Page 2 of 10... -
Page 3: Table Of Contents
1.2 Connecting Hardware ..............................5 1.3 Software Flashing ..............................5 1.4 Serial Communication ............................... 9 1.5 Project Customization ............................. 10 Ordering information ................................ 10 Technical support ................................10 _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change without notice Page 3 of 10... -
Page 4: Functional Description
Besides the headers, the board has 2 USB connectors for easy access to the UART interfaces and SWD interface. UART1 and the SWD interface are connected to USB1 and UART0 is connected to USB0. _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change... -
Page 5: Connecting Hardware
The Atmosic SDK can be downloaded from the Atmosic portal. In order to access this, please request access by contacting info@summit-electronics.com After installing the SDK, Connect the USB1 interface to the PC, leave USB0 unconnected for software flashing. Next navigate to the SDK folder and run the InstRDI executable, this will install the necessary drivers on your PC. - Page 6 If the drivers are installed correctly you should have 1 COM port, and 1 new device under USB-devices. If you have 2 COM ports, please check USB1 is connected and try InstRDI.exe again. _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change...
- Page 7 -DUART0_RAW_RTSPIN=24 \ -DUART0_RAW_BAUD=460800 After make sure to save the file. To load the example on the EVB, open the SDK_X.X.X executable. This will open the following window: _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change without notice Page 7 of 10...
- Page 8 After using “Make run” the program will build and load to the ERF1002 module. If you get an error, please check the path is correct, and also verify if the drivers are installed correctly: Path: Driver: _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change without notice...
-
Page 9: Serial Communication
Click terminal and set “Implicit LF in every CR” to On, and Local Echo to on. Next, select Session, Serial, and select the COM port and set the Baud to 460800. Now the COM port can be opened and AT-commands can be send. _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change... -
Page 10: Project Customization
Ordering can be done via www.summit-electronics.com or via info@summit-electronics.com. Please contact us for more information. Customisation of the product is available on request. Technical support For all product questions please contact us via info@summit-electronics.com. _________________________________________________________________________________________________ www.summit-electronics.com rev. -1- info@summit-electronics.com Subject to change...
Need help?
Do you have a question about the ERF1002 EVB and is the answer not in the manual?
Questions and answers