Table of Contents
Advertisement
Quick Links
Gamechanger Audio's AUTO Series M-Type pedals redefine classic audio effects with
cutting-edge parameter automation - carefully designed to become part of your performance.
Rather than overwhelming you with a variety of pre-made, quirky sounds, we provide you with
the essential toolset: three nuanced algorithms, four vital parameter controls, two exceptionally
precise dynamics & pitch tracker engines, and a set of patching accesories.
With these building blocks and the knowledge contained in this booklet - you will be able to
explore an endless array of sound possibilities. The combinations are virtually limitless, allowing
you to continuously breathe new life into the AUTO REVERB and create soundscapes that
naturally evolve with your playing, offering a unique musical experience every time.
Dive into this expansive world of creativity, where every patch and every performance reflects
your personal artistry, imagination and technical ability.
STARTING POSITION:
FRONT PANEL:
LEVEL knob
with mode switch:
IN: Amount of signal
sent into reverb engine
WET: Amount of signal
sent into reverb engine;
DRY output muted
MIX: Mix between fully
DRY output and fully
WET output
TONE knob:
Adjusts the reverb's
input stage tone, but
not the currently
audible reverb trails
PATCHBAY:
One input for each
parameter &
two identical
outputs per tracker
DYNAMICS knob:
Adjust DYNAMICS
THRESHOLD &
RELEASE values
DYNAMICS MODE
switch:
FAST-RISE-GATE
AUTO footswitch:
Toggles all incoming
and outgoing CV
AUTO REVERB
Automation mode
set to SUM
STEREO SPREAD
switch:
OFF-50%-100%
DYNAMICS BAR:
Input signal meter,
CV output,
DYN adjustment
ALGORITHM
switch:
PLATE-HALL-SPRING
PITCH BAR:
Indicates input
pitch/timbre and
CV output
All automation
knobs centered
DECAY knob:
Reverb engine's
decay time
CV IN LEDs:
Indicate incoming CV
for each parameter -
Blue for negative and
red for positive CV
FILTER knob:
Output stage filter
applied on active
reverb trails
AUTOMATION
Adjust and attenuate
incoming CV to set
automation range
& direction
AUTOMATION
MODE switch:
SUM-EXT-ALT
PITCH knob:
Adjust Pitch tracker
and RAMP value
PITCH MODE switch:
VOLT PER OCTAVE
ON/OFF footswitch
Toggles main effect
knobs:
NOTE
TONE
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GameChanger Audio AUTO REVERB
Summary of Contents for GameChanger Audio AUTO REVERB
- Page 1 With these building blocks and the knowledge contained in this booklet - you will be able to explore an endless array of sound possibilities. The combinations are virtually limitless, allowing you to continuously breathe new life into the AUTO REVERB and create soundscapes that naturally evolve with your playing, offering a unique musical experience every time.
-
Page 2: Automation Modes
PATCH-BAY & AUTOMATION CONTROLS: Each of the pedal's four parameters has a dedicated Automation input socket with a corresponding indication LED, and a mini-knob (AUTO Knob) used for adjusting the amount and direction of the incoming Control Voltage (CV). AUTOMATION is achieved by sending a CV into the according parameter’s CV Input, and attenuating the CV with the AUTOMATION mini-knob. - Page 3 DYNAMICS BAR: CV output White LED bar displays your instrument's level within the pedal's headroom at all times. Input lvl The THRESHOLD point is a bright segment that can be moved across the Threshold bar with the DYNAMICS knob. Control Voltage (CV) will be produced when the input signal reaches and crosses the THRESHOLD point, turning it red.
-
Page 4: Note Mode
PITCH BAR & PITCH MODES: The PITCH tracking engine analyzes the tonal content of the input signal at all times and displays it as a moving WHITE moving CURSOR on the PITCH LED Bar. Depending on the PITCH MODE and settings - the cursor will move in and out of CV ZONES - indicated as RED or BLUE LED segments on the PITCH BAR - the brightness shows output CV strength - up to 5V. -
Page 5: Firmware Update
PITCH RAMP parameter: Hold the ON footswitch and turn the PITCH knob to adjust the RAMP parameter - represented by YELLOW segments on the PITCH BAR. When turned all the way down, the PITCH tracker will follow your input pitch with maximum speed, whereas increasing the RAMP bar will make the PITCH tracker's output smoother by introducing a “glide”... -
Page 6: Back Panel
IMPORTANT! TRACK INPUT & SIGNAL CHAIN: To ensure precise signal tracking and CV generation - each AUTO Pedal needs to receive a CLEAN INPUT signal from your instrument. Any effects before the AUTO Pedal (modulation, gain, pitch, time-based, etc.) will affect the TRACKER’s ability to analyze input and produce CV. For best results - send a copy of the CLEAN SIGNAL into each AUTO Pedal’s TRACK Input. -
Page 7: Patch Ideas
PATCH IDEAS CUSTOM PRE-DELAY GATING/DUCKING VERB RISING REVERB Use GATE or FAST MODE with Set to MIX MODE and use Set DYN to RISE mode short RELEASE time. LEVEL AUTO KNOB and adjust THRESHOLD. Each new strum will briefly to adjust MIX INCREASE Playing dynamics will close down the INPUT LVL - on each new strum/note;... -
Page 8: Safety Information
You will only be responsible for return shipping charges. Each AUTO Series pedal manufactured by Gamechanger Audio is warranted to be free from defects in materials and workmanship for one year from the date of shipping or longer if required by the relevant legislation. - Page 9 MIDI CC MSB and LSB val range (CC[n] = MSB, CC CC NAME MSB val range [n+32] = LSB) LEVEL [0...127] = [0...1] [0...16383] = [0...1] DECAY [0...127] = [0...1] [0...16383] = [0...1] 10 TONE [0...127] = [0...1] [0...16383] = [0...1] 11 FILTER [0...127] = [0...1] [0...16383] = [0...1]...
-
Page 10: Technical Specification
TECHNICAL SPECIFICATION Connections Inputs L/MONO 6.35mm (1/4’’) TS socket R/TRS 6.35mm (1/4’’) TRS socket TRACK IN/INPUT 3.5mm (1/8’’) TRS socket - Track signal insert (L/R) CV IN 1 … 4 3.5mm (1/8’’) TS socket, Control Voltage inputs for effects parameter control Outputs L/MONO 6.35mm (1/4’’) TS socket...
Need help?
Do you have a question about the AUTO REVERB and is the answer not in the manual?
Questions and answers