Summary of Contents for Boss Ready To Go Rigid
- Page 1 Ready To Go Rigid Solar Kit System Installation Manual Australian Made Solar Pool Heating MANUFACTURED BY: Ready To Go Rigid Solar Kit | Installation Manual...
-
Page 2: Table Of Contents
VacRel Vacuum Relief Valve Drain Down Tube TufGauge Pressure Gauge TufFilta Inline Solar Filter Starting the System Installing Around Obstacles PVC Pipe Extension Manifold/Header Plugs Troubleshooting Guide 17-19 Caring for your System Ready To Go Rigid Solar Kit | Installation Manual... -
Page 3: Introduction
System cannot fully drain down. the system. For more information on working safely with heights, check out the Work Safe ‘Working with Heights’ website for more information http://www.worksafe.vic.gov.au/safety-and-prevention/ small-business/12-ways-to-make-small-businesses-safer/ working-at-heights Ready To Go Rigid Solar Kit | Installation Manual... -
Page 4: Required Tools
Suitable Fixing Screws • Pliers • Spirit Level • Pipe Cutter or Hacksaw • Tape Measure • Caulking Gun • PVC Cement • PVC Primer See all panel components on the next page. Ready To Go Rigid Solar Kit | Installation Manual... -
Page 5: Rigid Panel Parts
Ready To Go Rigid Components Ready To Go Rigid Solar Kit | Installation Manual... -
Page 6: How To Installthe Rigid System
Step 2 Using the diagram and table below, create a horizontal sloping line where the bottom Roof Mounts will be installed. Panel Model Dim A PAR3/010 1775 PAR3/014 2530 PAR3/018 3295 Ready To Go Rigid Solar Kit | Installation Manual... - Page 7 Secure the SHORT and LONG portions together using two screws. Secure the Roof Mount to the Tile Roof Bracket along the TOP of the system only using screws. DO NOT fasten the bottom Roof Mounts. Ready To Go Rigid Solar Kit | Installation Manual...
- Page 8 Install the supplied button Step 10 screw. Install the End Caps on the remaining corners using Ring Clamp Assemblies. Repeat until all Rigid Panels are connected. Ready To Go Rigid Solar Kit | Installation Manual...
-
Page 9: Plumb The System To The Pump House
The Return line is typically a single return outlet, usually higher on the pool wall than the suction lines. Plumb as per the diagram above. Ensure all pipework is dry and clean before attempting to glue. Ready To Go Rigid Solar Kit | Installation Manual... -
Page 10: Simultaneous / Integrated / Retro Fit Configuration
Switch the system off and isolate any valve/s (if possible) to minimise water loss. Identify the best position to cut into the line to install the two PVC Tees, Check Valve and Pump. Plumb as per the diagram above. Ensure all pipework is dry and clean before attempting to glue. Ready To Go Rigid Solar Kit | Installation Manual... -
Page 11: Manual System (No Pump Or Digital Controller)
(if possible) to minimise water loss. Identify the best position to cut into the line to install the three-Way Manual Valve, PVC Tee and Check Valve. Plumb as per the diagram above. Ensure all pipework is dry and clean before attempting to glue. Ready To Go Rigid Solar Kit | Installation Manual... -
Page 12: Install The Ancillery Components
Lubricate the and insert the rubber grommets into the drilled holes, tapered end first. Spray the newly installed grommets with silicone spray and insert the header barbs, lubricate and slide the tube over each barb. Ready To Go Rigid Solar Kit | Installation Manual... -
Page 13: Tufgauge Pressure Gauge
TufFilta. This enables the cartridge element to be removed and replaced without drenching equipment or the person performing the task. Installation Of TufFilta FLOW DIRECTION FLOW FLOW DIRECTION PREFERRED ACCEPTABLE NOT ACCEPTABLE Ready To Go Rigid Solar Kit | Installation Manual... -
Page 14: Starting The System
If bubbles continue to flow endlessly, it may be an If you come across any issues check the indication that air is entering the system via the VacRel. ‘Troubleshooting Guide’ at the back of this manual. Ready To Go Rigid Solar Kit | Installation Manual... -
Page 15: Installing Around Obstacles
Solar Panels can be Ensure that you use a good quality, multi-purpose installed. This may not be necessary if the distance is less cement. than 600mm (24 inches). Ready To Go Rigid Solar Kit | Installation Manual... -
Page 16: Manifold/Header Plugs
Barb Lock. The raised lip of the Barb Lock should be facing towards the collector. Push down firmly in the centre and then the outsides until you hear a click. Ready To Go Rigid Solar Kit | Installation Manual... -
Page 17: Troubleshooting Guide
If the pool is using a suction type pool cleaner, try avoid tampering removing it to see if the air bubbles clear up. If they do, only use the cleaner while the system is turned “OFF” Ready To Go Rigid Solar Kit | Installation Manual... - Page 18 “OFF” of panels that are the coolest to the throttle. Adjust the ball valve to back the flow through the system and force more water through the warmer panels. Ready To Go Rigid Solar Kit | Installation Manual...
- Page 19 Inspect to ensure all rubber seals are in place, undamaged, intact and clean. Replace any damaged seals if required. Once complete, insert the collector back into the manifold and secure using the barb lock. Ready To Go Rigid Solar Kit | Installation Manual...
-
Page 20: Caring For Your System
Check that there is no build-up of debris around pipe work or collectors, and that rainwater has a clear path to run down. Wintering System You may need to prepare your system for winter dormancy each year. Ready To Go Rigid Solar Kit | Installation Manual... - Page 21 Australian Made Solar Pool Heating AUSTRALIAN MADE SOLAR POOL HEATING sales@bosssolar.com.au MANUFACTURED BY: www.bosspoolheating.com.au 1300 786 489 Ready To Go Rigid Solar Kit | Installation Manual...
Need help?
Do you have a question about the Ready To Go Rigid and is the answer not in the manual?
Questions and answers