ebm-papst G1G126-AA49-70 Operating Instructions Manual
ebm-papst G1G126-AA49-70 Operating Instructions Manual

ebm-papst G1G126-AA49-70 Operating Instructions Manual

Advertisement

Quick Links

G1G126-AA49-70
ASIA PACIFIC SHENGRUI LIMITED
Phone +00852 56261528
info@apacshengrui.com
www.apacfan.com
CONTENTS
Item no. 56391-5-9970 · ENU · Change 202174 · Approved 2018-12-27 · Page 1 / 11
Operating instructions

1. SAFETY REGULATIONS AND INFORMATION

Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1

1.1 Hazard levels for warnings

1
1
These operating instructions use the following hazard levels to indicate
1
potentially hazardous situations and important safety regulations:
1
2
2
2
2
2
2
2
3
4
4
5
5
5
5
ASIA PACIFIC SHENGRUI LIMITED Phone +00852
6
56261528

1.2 Staff qualifications

6
info@apacshengrui.com
The device may only be transported, unpacked, installed, operated,
6
www.apacfan.com
maintained and otherwise used by suitably qualified, trained and
7
authorized technical staff.
8
Only authorized specialists are permitted to install the device, to carry
9
out a test run and to perform work on the electrical installation.
9
9

1.3 Basic safety rules

9
The safety hazards associated with the device must be assessed again
following installation in the final product.
9
The locally applicable industrial safety regulations are always to be
observed when working on the device.
10
Keep the workplace clean and tidy. Untidiness in the work area
10
increases the risk of accidents.
10
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.

1.4 Voltage

; Check the device's electrical equipment at regular intervals; see
Chapter 6.2 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Indicates an imminently hazardous situation which will result in
death or serious injury if the specified actions are not taken.
Compliance with the instructions is imperative.
WARNING
Indicates a potentially hazardous situation which can result in
death or serious injury if the specified actions are not taken.
Exercise extreme caution while working.
CAUTION
Indicates a potentially hazardous situation which can result in
minor or moderate injury or damage to property if the specified
actions are not taken.
NOTE
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G1G126-AA49-70 and is the answer not in the manual?

Questions and answers

Summary of Contents for ebm-papst G1G126-AA49-70

  • Page 1: Table Of Contents

    6.3 Disposal Note the following when working on the device: ; Do not perform any modifications, additions or conversions on the device without the approval of ebm-papst. 1.4 Voltage ; Check the device's electrical equipment at regular intervals; see Chapter 6.2 Safety inspection.
  • Page 2: Safety And Protective Features

    Operating instructions G1G126-AA49-70 WARNING 1.7 Mechanical movement Live terminals and connections even with device DANGER switched off Rotating device Electric shock Risk of injury to body parts coming into contact with the rotor or → Wait five minutes after disconnecting the voltage at all poles the impeller.
  • Page 3: Intended Use

    Operating instructions G1G126-AA49-70 2. INTENDED USE The device is exclusively designed as a built-in device for conveying air according to its technical data. Any other usage above and beyond this does not conform with the intended purpose and constitutes misuse of the device.
  • Page 4: Technical Data

    Operating instructions G1G126-AA49-70 3. TECHNICAL DATA 3.1 Product drawing All dimensions in mm. Housing side parts sealed with NBR round cord (pentane-resistant) 3-pole header; mating connector (not included in scope of delivery): tyco no. 350 766-1; socket: tyco no. 926 884-1 5-pole header;...
  • Page 5: Nominal Data

    With regard to cyclic speed loads, note that the rotating parts of the device are designed for a maximum of one million load Motor M1G055-BD cycles. If you have special questions, consult ebm-papst for support. Phase ; Use the device in accordance with its degree of protection.
  • Page 6: Connection And Startup

    Operating instructions G1G126-AA49-70 4. CONNECTION AND STARTUP CAUTION Voltage The device is a built-in component and has no disconnecting 4.1 Mechanical connection switch. CAUTION → Only connect the device to circuits that can be switched off Cutting and crushing hazard when removing blower with an all-pole disconnection switch.
  • Page 7: Plug Connection

    Operating instructions G1G126-AA49-70 4.2.4 Locked-rotor protection Due to the locked-rotor protection, the starting current (LRA) is equal to or less than the nominal current (FLA). 4.3 Plug connection 4.3.1 Making supply connections ; Check your connector's pin assignment. ; Connect the built-in connector with the mating connector.
  • Page 8: Connection Diagram

    Operating instructions G1G126-AA49-70 4.4 Connection diagram Drawing preliminary! Item no. 56391-5-9970 · ENU · Change 202174 · Approved 2018-12-27 · Page 8 / 11...
  • Page 9: Checking Connections

    Operating instructions G1G126-AA49-70 4.5 Checking connections 5. INTEGRATED PROTECTIVE FEATURES ; Ensure isolation from supply (all phases). The integrated protective functions cause the motor to switch off automatically in the event of the faults described in the table. ; Make sure a restart is impossible ;...
  • Page 10: Cleaning

    AC voltage required by cool down. the standard. What to check How to check How often What action? In the event of further malfunctions, contact ebm-papst. Contact Visual inspection At least every Repair or protection 6 months replacement of...
  • Page 11 Electrolytic capacitors ● Dispose of electronic components employing the proper procedures for electronic scrap. → Please contact ebm-papst for any other questions on disposal. Item no. 56391-5-9970 · ENU · Change 202174 · Approved 2018-12-27 · Page 11 / 11...

Table of Contents