Subscribe to Our Youtube Channel
Summary of Contents for HMS Networks Anybus Wireless Bolt 5G NV200
- Page 1 ENGLISH ® ™ Anybus Wireless Bolt 5G STARTUP GUIDE SP3197 Version 1.0 Publication date 2024-07-09...
- Page 2 The information in this document shall therefore not be construed as a commitment on the part of HMS Networks and is subject to change without notice. HMS Networks makes no commitment to update or keep current the information in this document.
-
Page 3: About This Document
® ™ Preface Anybus Wireless Bolt 5G 1. Preface 1.1. About This Document ® ™ This document describes how to install Anybus Wireless Bolt 5G For additional documentation, software downloads and technical support, please visit www.hms-networks.com. 1.2. Document Conventions Safety Symbols DANGER Instructions that must be followed to avoid an imminently hazardous situation which, if not avoided, will result in death or serious injury. -
Page 4: Information Symbols
Additional information which may facilitate installation and/or operation. Helpful advice and suggestions. 1.3. Trademarks ® ™ Anybus Wireless Bolt 5G is a trademarks of HMS Networks AB. All other trademarks are the property of their respective holders. Page 2 of 36 SP3197 Version 1.0... -
Page 5: General Safety
® ™ Safety Anybus Wireless Bolt 5G 2. Safety 2.1. General Safety CAUTION Ensure that the power supply is turned off before connecting it to the equipment. CAUTION To ensure proper functioning and electrical safety, connect the Bolt 5G Functional Earth (FE) connection to earth. CAUTION The supply circuit must be limited to PS2 or fulfill the requirements in IEC 62368-1:2023 standard Annex Q, equivalent to Limited Power Source... -
Page 6: Intended Use
® ™ Anybus Wireless Bolt 5G Intended Use 2.2. Intended Use The intended use of this equipment is as a communication interface and router. The equipment receives and transmits data over wired and cellular standard networks. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. -
Page 7: Network Environment
® ™ Preparation Anybus Wireless Bolt 5G 3. Preparation 3.1. Support and Resources For additional documentation, software downloads and technical support, please visit www.hms-networks.com. 3.2. Network Environment Ensure that you have all the necessary information about the capabilities and restrictions of your local network environment before installation. - Page 8 ® ™ Anybus Wireless Bolt 5G Surface Heat Considerations 3.5. Surface Heat Considerations Mount the Bolt 5G on a surface with good thermal conductance to the surrounding air. For optimal thermal performance, it is recommended that the heat transfer capacity of the surface corresponds to a square aluminum plate with a minimum side dimension of 300 mm and a thickness of 3 mm.
-
Page 9: Supported Operating Systems
® ™ HMS Software Applications Anybus Wireless Bolt 5G 3.7. HMS Software Applications Download the software installation files and user documentation from www.hms-networks.com. Supported Operating Systems Operating System Description Windows 7 SP1, 32-bit Windows 7 32-bit with Service Pack 1 Windows 7 SP1, 64-bit Windows 7 64-bit with Service Pack 1 Windows 10 64-bit... -
Page 10: Installation
® ™ Anybus Wireless Bolt 5G Installation 4. Installation 4.1. Install SIM Card NOTE The supported SIM card type is Nano SIM (4FF). Figure 2. Insert SIM card To connect Bolt 5G to a cellular data network, install a cellular SIM card: Remove the SIM card holder plug. -
Page 11: Installation Drawing
® ™ Installation Drawing Anybus Wireless Bolt 5G 4.2. Installation Drawing All measurements are in mm. Figure 3. Bolt 5G installation drawing SP3197 Version 1.0 Page 9 of 36... -
Page 12: Surface Mounting
® ™ Anybus Wireless Bolt 5G Surface Mounting 4.3. Surface Mounting Before You Begin Mounting Considerations • Mount the Bolt 5G on a machine or cabinet. • For information about surface heat considerations, see Surface Heat Considerations (page • Mounting hole diameter: M50 (50,5 mm). •... - Page 13 ® ™ Surface Mounting Anybus Wireless Bolt 5G Place the Bolt 5G housing sealing ring in its groove. In the mounting surface, drill a mounting hole with the size Ø M50 (50,5 mm). Option: To fix the Bolt 5G position, see To Lock the Bolt 5G Position (page 13).
- Page 14 ® ™ Anybus Wireless Bolt 5G Surface Mounting Screw the Bolt 5G lock nut into place and tighten it. Tightening torque: 5 Nm ±10 % IMPORTANT To keep the Bolt 5G sealed against dirt and moisture, make sure the housing sealing ring is properly seated in its groove before tightening the lock nut.
- Page 15 ® ™ To Lock the Bolt 5G Position Anybus Wireless Bolt 5G 4.4. To Lock the Bolt 5G Position The complete surface mounting procedure is described in, Surface Mounting (page 10). Figure 4. Bolt 5G steering hole for locking screw To prevent the Bolt 5G from being rotated, use a screw and the Bolt 5G steering hole to fix the position.
- Page 16 ® ™ Anybus Wireless Bolt 5G To Lock the Bolt 5G Position Procedure Drill a mounting hole with the size Ø M50 (50,5 mm) for the Bolt 5G and a hole with the size Ø 3 mm for the locking screw. All measurements are in mm.
- Page 17 ® ™ To Lock the Bolt 5G Position Anybus Wireless Bolt 5G Fasten the locking screw in the Ø 3 mm hole. Place the Bolt 5G in the surface mounting hole and fit the locking screw into the Bolt 5G steering hole. SP3197 Version 1.0 Page 15 of 36...
- Page 18 ® ™ Anybus Wireless Bolt 5G Signal and Power Connector Cabling 4.5. Signal and Power Connector Cabling 4.5.1. Signal and Power Connector Pinout An 18-pin connector cable assembly with individual wire leads is included with the product. Table 1. 18-Pin Signal and Power Connector Function Color 1-14, 16...
-
Page 19: Connector Type
® ™ Signal and Power Connector Cabling Anybus Wireless Bolt 5G IMPORTANT To prevent wires from overheating, use a power supply wire rated to carry the rated current of the Bolt 5G. 4.5.3. Connector Type An 18-pin connector cable assembly with individual wire leads is included with the product. -
Page 20: Connect To Dc Power
® ™ Anybus Wireless Bolt 5G Connect to DC Power 4.6. Connect to DC Power Option when you use DC Power. To use Power over Ethernet (PoE), see Connect to Power Over Ethernet (PoE). Before You Begin CAUTION To ensure proper functioning and electrical safety, connect the Bolt 5G Functional Earth (FE) connection to earth. - Page 21 ® ™ Connect to DC Power Anybus Wireless Bolt 5G Figure 6. Functional earth wire screw placement, view from below SP3197 Version 1.0 Page 19 of 36...
- Page 22 ® ™ Anybus Wireless Bolt 5G Connect to DC Power Procedure Connect to DC Power and Functional Earth (FE) Figure 7. DC Power and Functional Earth (FE) Connect Bolt 5G Power connector to Functional Earth (FE). Connect Bolt 5G Power connector to a power supply. Page 20 of 36 SP3197 Version 1.0...
- Page 23 ® ™ Connect to Power Over Ethernet (PoE) Anybus Wireless Bolt 5G 4.7. Connect to Power Over Ethernet (PoE) Option when you use Power over Ethernet (PoE). To use DC Power, see Connect to DC Power (page 18). Before You Begin CAUTION To ensure proper functioning and electrical safety, connect the Bolt 5G Functional Earth (FE) connection to earth.
- Page 24 ® ™ Anybus Wireless Bolt 5G Connect to Power Over Ethernet (PoE) Figure 8. Functional earth wire screw placement, view from below Procedure Figure 9. Connect to Power Over Ethernet (PoE) Page 22 of 36 SP3197 Version 1.0...
- Page 25 ® ™ Connect to Power Over Ethernet (PoE) Anybus Wireless Bolt 5G Connect the Bolt 5G to Functional Earth (FE). Use the Bolt 5G steering hole to connect the functional earth connection cable to the Bolt 5G. Functional Earth (FE) Wire Screw Placement (page 21) To Lock the Bolt 5G Position (page 13).
-
Page 26: Connect To Ethernet
® ™ Anybus Wireless Bolt 5G Connect to Ethernet 4.8. Connect to Ethernet Figure 10. Connect to Ethernet Connect the Bolt 5G to Ethernet network. Page 24 of 36 SP3197 Version 1.0... - Page 27 ® ™ Frequency Bands and Power Level Anybus Wireless Bolt 5G 4.9. Frequency Bands and Power Level Standard Mode Bands Frequency (MHz) Transmit Power UMTS (Universal Wideband Code Division Multiple Access 1920 – 1980 25 dBm Mobile (WCDMA) 1850 – 1910 Telecommunications System) 1710 –...
- Page 28 ® ™ Anybus Wireless Bolt 5G Frequency Bands and Power Level Standard Mode Bands Frequency (MHz) Transmit Power 2300 – 2400 5150 – 5925 3550 – 3700 2570 – 2620 28 dBm 2496 – 2690 3400 – 3600 3600 – 3800 5G NR (New Radio) Non-standalone (NSA) 1920 –...
- Page 29 ® ™ Frequency Bands and Power Level Anybus Wireless Bolt 5G Standard Mode Bands Frequency (MHz) Transmit Power 2496 – 2690 3300 – 4200 3300 – 3800 4400 – 5000 SP3197 Version 1.0 Page 27 of 36...
- Page 30 ® ™ Anybus Wireless Bolt 5G Configuration 5. Configuration 5.1. Connect to Configure 5.1.1. Connect to PC and DC Power Option if you use DC Power. When configuring Bolt 5G it must be connected to a PC. Figure 11. Connect to PC and Power Connect the Bolt 5G Ethernet port to your PC.
- Page 31 ® ™ Connect to Configure Anybus Wireless Bolt 5G 5.1.2. Connect to PC and Power over Ethernet (PoE) Option if you use Power over Ethernet (PoE). When configuring Bolt 5G it must be connected to a PC. Figure 12. Connect to PC and PoE Connect the Bolt 5G Ethernet port to the PoE injector PoE port.
- Page 32 ® ™ Anybus Wireless Bolt 5G Required IP Address Settings 5.2. Required IP Address Settings NOTE The Bolt 5G default IP address is 192.168.0.1 and the subnet mask is 255.255.255.0. On the PC accessing the Bolt 5G built-in web interface, set a static IP address within the same IP address range as the Bolt 5G IP address.
- Page 33 ® ™ Login to the Built-In Web Interface Anybus Wireless Bolt 5G 5.3. Login to the Built-In Web Interface The Bolt 5G built-in web interface can be accessed from a standard web browser. Before You Begin IMPORTANT For cybersecurity reasons, you are prompted to change the password at first login using the Bolt 5G factory default password.
- Page 34 ® ™ Anybus Wireless Bolt 5G Login to the Built-In Web Interface Enter Username and Password and click Login. Figure 14. Built-in web interface login screen Result You are logged in to the Bolt 5G built-in web interface Home page. Page 32 of 36 SP3197 Version 1.0...
- Page 35 ® ™ Configure the Bolt 5G Anybus Wireless Bolt 5G 5.4. Configure the Bolt 5G Procedure Figure 15. The Bolt 5G built-in web interface Home page Open the Bolt 5G built-in web interface in HMS IPconfig or enter the Bolt 5G IP address in your web browser.
-
Page 36: Technical Specifications
® ™ Anybus Wireless Bolt 5G Technical Specifications 6. Technical Specifications Additional technical data and information related to the installation and use of this product can be found at www.hms-networks.com. Model identification NV200 Communication connector RJ45 Ethernet 10/100/1000 Mbit/s, PoE Signal and power connector 18-Pin signal and power connector, Phoenix Contact PCB connector DFMC 0,5/ 9-ST-2,54... - Page 37 ® ™ Ethernet RJ45 LED Status Indication Anybus Wireless Bolt 5G 7. Ethernet RJ45 LED Status Indication Figure 16. RJ45 Ethernet LED indicators LED A – LINK/ACTIVITY Function No Ethernet link Yellow Ethernet link established Yellow, flashing 10/100/1000 Mbps Ethernet link activity LED B –...
- Page 38 ® ™ Anybus Wireless Bolt 5G Bolt 5G LED Status Indication 8. Bolt 5G LED Status Indication Figure 17. Bolt 5G LED Indicators LED A LED B LED C LED D LED E LED F LED Status Cellular Status Power SPE RX LED SPE TX LED IO-Link Activity...
Need help?
Do you have a question about the Anybus Wireless Bolt 5G NV200 and is the answer not in the manual?
Questions and answers