Download Print this page

Advertisement

Dell Vostro 3350
Owner's Manual
Regulatory Model P13S
Regulatory Type P13S001

Advertisement

   Summary of Contents for Dell Vostro 3350

  • Page 1

    Dell Vostro 3350 Owner's Manual Regulatory Model P13S Regulatory Type P13S001...

  • Page 2: Notes, Cautions, And Warnings

    Information in this publication is subject to change without notice. © 2011 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell...

  • Page 3: Table Of Contents

    Contents Notes, Cautions, and Warnings..............2 1 Working on Your Computer..............7 ................7 Before Working Inside Your Computer ......................9 Recommended Tools ....................9 Turning Off Your Computer ................9 After Working Inside Your Computer 2 Battery......................11 .....................11 Removing The Battery ......................12 Installing The Battery 3 Memory Card....................13 ...................13 Removing The Memory Card...

  • Page 4: Table Of Contents

    .....................22 Installing The Optical Drive 8 Hard Drive....................23 ....................23 Removing The Hard Drive ....................26 Installing The Hard Drive 9 Wireless Local Area Network (WLAN) Card........27 ..........27 Removing Wireless Local Area Network (WLAN) Card ..........28 Installing The Wireless Local Area Network (WLAN) Card 10 Keyboard....................29 ....................29 Removing The Keyboard...

  • Page 5: Table Of Contents

    16 Power-Button Board................55 ................55 Removing The Power-Button Board ................56 Installing The Power-Button Board 17 Quick Launch Button Board..............57 ..............57 Removing The Quick Launch Button Board ..............58 Installing The Quick Launch Button Board 18 Coin-Cell Battery..................61 ..................61 Removing The Coin-Cell Battery ..................61 Installing The Coin-Cell Battery 19 Heat Sink....................63...

  • Page 6: Table Of Contents

    29 System Setup..................95 ....................95 System Setup Overview ......................95 System Setup Enter ....................96 System Setup Screens .....................97 System Setup Options 30 Diagnostics....................101 ......................101 Device Status Lights .....................101 Battery Status Lights ....................101 Diagnostic Beep Codes 31 Specifications..................103 32 Contacting Dell..................113 ......................113 Contacting Dell...

  • Page 7: Working On Your Computer, Before Working Inside Your Computer

    Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

  • Page 8

    CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable.

  • Page 9: Recommended Tools, Turning Off Your Computer, After Working Inside Your Computer

    11. Remove any installed ExpressCards or Smart Cards from the appropriate slots. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • #0 Phillips screwdriver • #1 Phillips screwdriver • Small plastic scribe •...

  • Page 10

    CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard.

  • Page 11: Battery, Removing The Battery

    Battery Removing The Battery Before Working On Your Computer . Follow the procedures in Slide the release latches to unlock the battery. Slide the battery and remove it from the computer.

  • Page 12: Installing The Battery

    Installing The Battery Slide the battery into its slot until it clicks into place. After Working Inside Your Computer . Follow the procedures in...

  • Page 13: Memory Card, Removing The Memory Card

    Memory Card Removing The Memory Card Before Working On Your Computer . Follow the procedures in Press in on the memory card to release it from the computer. Slide the memory card out of the computer.

  • Page 14: Installing The Memory Card

    Installing The Memory Card Push the memory card into the compartment until it snaps into place. After Working Inside Your Computer . Follow the procedures in...

  • Page 15: Subscriber Identity Module (sim) Card, Removing The Phone Subscriber Identity Module (sim)

    Subscriber Identity Module (SIM) Card Removing The Phone Subscriber Identity Module (SIM) Before Working On Your Computer . Follow the procedures in battery . Remove the Press in on the SIM card to release it from the computer. Grasp the SIM card and pull out to release it from the computer.

  • Page 16: Installing The Phone Subscriber Identity Module (sim)

    Installing The Phone Subscriber Identity Module (SIM) Push the SIM card into the slot until it is fully engaged. battery . Install the After Working Inside Your Computer . Follow the procedures in...

  • Page 17: Access Panel, Removing The Access Panel

    Access Panel Removing The Access Panel Before Working On Your Computer . Follow the procedures in battery . Remove the Remove the screws that secures the access panel to the base of the computer. Lift the access panel up at an angle and remove it from the computer.

  • Page 18: Installing The Access Panel

    Installing The Access Panel Tighten the screws to secure the access panel to the base of the computer. battery . Install the After Working Inside Your Computer . Follow the procedures in...

  • Page 19: Memory, Removing The Memory Module

    Memory Removing The Memory Module Before Working On Your Computer Follow the procedures in battery . Remove the access panel . Remove the Pry the retention clips away from the memory module until it pops up. Remove the memory module from its connector on the system board.

  • Page 20: Installing The Memory Module

    Installing The Memory Module Insert and secure the memory module to the system board. access panel . Install the battery . Install the After Working Inside Your Computer . Follow the procedures in...

  • Page 21: Optical Drive, Removing The Optical Drive

    Optical Drive Removing The Optical Drive Before Working On Your Computer . Follow the procedures in battery . Remove the access panel . Remove the Remove the screw that secures the optical drive to the computer. Use a screwdriver to pry the optical drive out of the computer.

  • Page 22: Installing The Optical Drive

    Installing The Optical Drive Slide the optical drive into its compartment on the chassis. Tighten the screw to secure the optical drive to the computer. access panel . Install the battery . Install the After Working Inside Your Computer . Follow the procedures in...

  • Page 23: Hard Drive, Removing The Hard Drive

    Hard Drive Removing The Hard Drive Before Working On Your Computer . Follow the procedures in battery . Remove the access panel . Remove the Open the clip that secures the hard-drive assembly to the computer. Disconnect the hard-drive cable from the hard drive.

  • Page 24

    Remove the screws that secure the hard-drive assembly to the computer. Lift the hard drive up at an angle from the system and remove it from the computer.

  • Page 25

    Remove the screws that secure the hard-drive bracket to the hard drive. Lift the hard-drive bracket up and away from the hard drive.

  • Page 26: Installing The Hard Drive

    10. Remove the hard drive board from the hard drive. Installing The Hard Drive Install the screws to secure the hard drive board to the hard drive. Place the hard drive in its compartment . Replace the screws to secure the hard drive to the system. Connect the hard drive cable to the system board.

  • Page 27: Wireless Local Area Network (wlan) Card, Removing Wireless Local Area Network (wlan) Card

    Wireless Local Area Network (WLAN) Card Removing Wireless Local Area Network (WLAN) Card Before Working On Your Computer . Follow the procedures in battery . Remove the Remove the access panel. Disconnect the antenna cables from the WLAN card. Use a scribe to pry the latch to release the WLAN card.

  • Page 28: Installing The Wireless Local Area Network (wlan) Card

    Remove the WLAN card from the computer. Installing The Wireless Local Area Network (WLAN) Card Slide the WLAN card into its slot. Connect the antenna cables according to the color code on the WLAN card. access panel . Install the battery .

  • Page 29: Keyboard, Removing The Keyboard

    Keyboard Removing The Keyboard Before Working On Your Computer . Follow the procedures in battery . Remove the Using a small plastic scribe, release the four latches that secures the keyboard to the computer. Flip the keyboard over and lay it on the palm rest.

  • Page 30

    Open the clip to release the keyboard cable. Disconnect the keyboard cable from its connector on the system board.

  • Page 31: Installing The Keyboard

    If your computer comes with a backlit keyboard, disconnect the keyboard backlight cable. Remove the keyboard from the computer. Installing The Keyboard Connect the keyboard data cable to the system board. battery . Install the After Working Inside Your Computer . Follow the procedures in...

  • Page 33: Wireless Wide Area Network (wwan) Card, Removing The Wireless Wide Area Network (wwan) Card

    Wireless Wide Area Network (WWAN) Card Removing The Wireless Wide Area Network (WWAN) Card Before Working On Your Computer . Follow the procedures in battery . Remove the keyboard Remove the Open the power button board cable securing clip. Disconnect the power button board cable.

  • Page 34

    Disconnect the antenna cables from the WWAN card. Use a scribe to pry the latch that secures the WWAN card.

  • Page 35: Installing The Wireless Wide Area Network (wwan) Card

    Remove the WWAN card from the computer. Installing The Wireless Wide Area Network (WWAN) Card Slide the Wireless Wide Area Network (WWAN) card into its slot. Connect the antenna cables according to the color code on the WWAN card. power button board cable . Install the keyboard .

  • Page 37: Palm Rest, Removing The Palm Rest

    Palm Rest Removing The Palm Rest Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the hard drive . Remove the keyboard . Remove the Remove the rubber from the bottom of the computer. Remove the screws that secure the palm rest to the bottom of the computer.

  • Page 38

    Open the clip that secures the power-button board cable to the system board. 10. Disconnect the power-button board cable from its connector on the system board.

  • Page 39

    11. Open the clip that secures the LED board cable to the system board. 12. Disconnect the LED board cable from its connector on the system board.

  • Page 40

    13. Open the clip that secures the touchpad data cable to the system board. 14. Disconnect the touchpad data cable from its connector on the system board. 15. Open the clip that secures the finger print reader cable to the system board.

  • Page 41

    16. Disconnect the finger print reader cable from its connector on the system board. 17. Open the clip that secures the quick launch board cable to the system board.

  • Page 42

    18. Disconnect the quick launch board cable from its connector on the system board. 19. Remove the screws that secure the palm rest to the front of the computer.

  • Page 43

    20. Pry along the edges of the palm rest to release the palm rest. 21. Lift the palm rest up and away from the computer.

  • Page 44: Installing The Palm Rest

    Installing The Palm Rest Starting from the right edge of the palm rest, press downwards on the computer to engage the tabs. Work your way around the edges and ensure the tabs are fully engaged. Connect all cables to the system board. Tighten the screws to secure the palm rest.

  • Page 45: Speaker, Removing The Speaker

    Speaker Removing The Speaker Before Working on Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the hard drive . Remove the keyboard . Remove the palm rest . Remove the Disconnect the speaker cable from its connector on the system board.

  • Page 46: Installing The Speaker

    10. Release the speaker cable from the routing channel. 11. Lift the speakers up and away from the computer. Installing The Speaker Install the speaker cable in the routing channel. Install the speaker to its securing posts. Connect the speaker cable. palm rest .

  • Page 47

    battery . Install the After Working Inside Your Computer . 10. Follow the procedures in...

  • Page 49: Fingerprint Reader, Removing The Fingerprint Reader

    Fingerprint Reader Removing The Fingerprint Reader Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the hard drive . Remove the keyboard . Remove the palm rest . Remove the Release the fingerprint reader cable from the adhesive affixing it to the palm rest.

  • Page 50

    10. Lift up the fingerprint reader bracket at an angle and remove it from the computer. 11. Lift up the fingerprint reader board and remove.

  • Page 51: Installing The Fingerprint Reader

    Installing The Fingerprint Reader Install the fingerprint reader board and the bracket. Tighten the screws that secure the fingerprint reader bracket. Affix the finger print reader cable to the palm rest. palm rest . Install the keyboard . Install the hard drive Install the access panel .

  • Page 53: Led Board, Removing The Led Board

    LED Board Removing The LED Board Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the hard drive . Remove the keyboard . Remove the palm rest . Remove the Peel open the tape that secures the LED board cable.

  • Page 54: Installing The Led Board

    Installing The LED Board Secure the latches to the LED board. Affix the tape to secure the LED board cable. palm rest . Install the keyboard . Install the hard drive Install the access panel . Install the memory card . Install the battery .

  • Page 55: Power-button Board, Removing The Power-button Board

    Power-Button Board Removing The Power-Button Board Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the memory . Remove the hard drive . Remove the keyboard . Remove the palm rest .

  • Page 56: Installing The Power-button Board

    Installing The Power-Button Board Install the power-button board and tighten the screw. palm rest . Install the keyboard . Install the hard drive Install the memory . Install the access panel . Install the memory card . Install the battery . Install the After Working Inside Your Computer .

  • Page 57: Quick Launch Button Board, Removing The Quick Launch Button Board

    Quick Launch Button Board Removing The Quick Launch Button Board Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the memory . Remove the hard drive . Remove the keyboard .

  • Page 58: Installing The Quick Launch Button Board

    11. Pry the latches to release the quick launch button board; then lift up and remove it from the computer. Installing The Quick Launch Button Board Install the quick launch button board and tighten the screw. Affix the quick launch button board cable to the palm rest. palm rest .

  • Page 59

    battery . Install the After Working Inside Your Computer . 10. Follow the procedures in...

  • Page 61: Coin-cell Battery, Removing The Coin-cell Battery, Installing The Coin-cell Battery

    Coin-Cell Battery Removing The Coin-Cell Battery Before Working on Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the hard drive . Remove the keyboard . Remove the palm rest . Remove the Pry the tabs that secure the coin-cell battery to the system board.

  • Page 62

    hard drive . Install the access panel . Install the memory card Install the battery Install the After Working Inside Your Computer . Follow the procedures in...

  • Page 63: Heat Sink, Removing The Heat Sink

    Heat Sink Removing The Heat Sink Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the memory . Remove the WLAN card . Remove the optical drive . Remove the hard drive .

  • Page 64: Installing The Heat Sink

    Installing The Heat Sink Install the heat sink in the slot. system board Install the display assembly . Install the palm rest . Install the WWAN card . Install the keyboard . Install the hard drive Install the optical drive . Install the WLAN card .

  • Page 65: Processor, Removing The Processor

    Processor Removing The Processor Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the memory . Remove the WLAN card . Remove the optical drive . Remove the hard drive .

  • Page 66: Installing The Processor

    15. Lift the processor up and away from the system board. Installing The Processor Insert the processor into the processor socket. Ensure the processor is properly seated. Tighten the cam lock in a clockwise direction. system board Install the display assembly . Install the palm rest .

  • Page 67

    optical drive . Install the WLAN card . 10. Install the memory . 11. Install the access panel . 12. Install the memory card . 13. Install the battery . 14. Install the After Working Inside Your Computer . 15. Follow the procedures in...

  • Page 69: Display Assembly, Removing The Display Assembly

    Display Assembly Removing The Display Assembly Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the WLAN card . Remove the hard drive . Remove the keyboard .

  • Page 70

    12. Disconnect the display cable from the system board. 13. Release the WWAN cables from the routing channel.

  • Page 71: Installing The Display Assembly

    14. Remove the screws that secure the display assembly to the computer. 15. Lift the display assembly up from the computer, then forward and remove. Installing The Display Assembly Attach the display assembly to the base of the computer. Tighten the screws to secure the display assembly. Secure the antenna cables to the routing channels.

  • Page 72

    hard drive . Install the WLAN card . 10. Install the access panel . 11. Install the memory card . 12. Install the battery . 13. Install the After Working Inside Your Computer . 14. Follow the procedures in...

  • Page 73: Display Bezel, Removing The Display Bezel

    Display Bezel Removing The Display Bezel Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the WLAN card . Remove the hard drive . Remove the keyboard .

  • Page 74: Installing The Display Bezel

    Installing The Display Bezel Place the display bezel on the computer. Starting from the bottom edge, press downward on the display bezel to engage the tabs. Work your way around the sides and top edge. palm rest . Install the WWAN card .

  • Page 75: Camera, Removing The Camera

    Camera Removing The Camera Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the WLAN card . Remove the hard drive . Remove the keyboard . Remove the WWAN card .

  • Page 76: Installing The Camera

    14. Pry the latch; then lift up the camera. Installing The Camera Install display camera and connect the camera cable. Stick back tape that secures the display camera.. display bezel . Install the display assembly . Install the palm rest . Install the WWAN card .

  • Page 77

    access panel . 10. Install the memory card . 11. Install the battery . 12. Install the After Working Inside Your Computer . 13. Follow the procedures in...

  • Page 79: Display Panel, Removing The Display Panel

    Display Panel Removing The Display Panel Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the WLAN card . Remove the hard drive . Remove the keyboard .

  • Page 80

    14. Remove the tape that secures the display cable to the display panel. 15. Disconnect the display panel cable from its connector on the panel.

  • Page 81: Installing The Display Panel

    Installing The Display Panel Install the display cable on the display panel. Replace the tape to secure the display cable to the display panel. Install the screws that secure the display panel to the display assembly. display bezel Install the display assembly Install the palm rest .

  • Page 83: Display Brackets And Hinges, Removing Display Brackets And Hinges

    Display Brackets and Hinges Removing Display Brackets And Hinges Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the WLAN card . Remove the hard drive . Remove the keyboard .

  • Page 84

    14. Turn over the left display bracket and hinge. 15. Release the cables from the left hinge; then remove the left display bracket and hinge. 16. Release the cables from the right hinge; then remove the right display bracket and hinge.

  • Page 85: Installing The Display Brackets And Hinges

    Installing The Display Brackets And Hinges Install the display brackets and display hinges. Tighten the screws to secure the display brackets and hinges to the display assembly. Route the cables into the right and left hinges. display panel Install the display bezel Install the display assembly...

  • Page 87: Display Cable, Removing The Display Cable

    Display Cable Removing The Display Cable Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the WLAN card . Remove the hard drive . Remove the keyboard .

  • Page 88: Installing The Display Cable

    Installing The Display Cable Install the display cable affixing it to the display cover. display brackets and hinges . Install the display panel . Install the display camera . Install the display bezel . Install the display assembly . Install the palm rest .

  • Page 89: System Board, Removing The System Board

    System Board Removing The System Board Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the memory . Remove the WLAN card . Remove the optical drive . Remove the hard drive .

  • Page 90

    15. Remove the screws that secure the system board to the computer. 16. Lift the system board up and away from the computer.

  • Page 91: Installing The System Board

    Installing The System Board Align the system board to the port connectors on the rear of the chassis and place the system board in the computer. Tighten the screws to secure the system board in place. Replace the fan cable. Tighten the screws to secure the heatsink to the system board.

  • Page 93: Input/output Board, Removing The Input/output (i/o) Board

    Input/Output Board Removing The Input/Output (I/O) Board Before Working On Your Computer . Follow the procedures in battery . Remove the memory card . Remove the access panel . Remove the WLAN card . Remove the optical drive Remove the hard drive .

  • Page 94: Installing The Input/output Board

    Installing The Input/Output Board Install the Input/Output board into the slot. system board Install the display assembly . Install the palm rest . Install the WWAN card . Install the keyboard . Install the hard drive Install the optical drive . Install the WLAN card .

  • Page 95: System Setup, System Setup Overview, System Setup Enter

    Certain changes can cause your computer to work incorrectly. System Setup Enter Turn on (or restart) your computer. When the blue DELL logo is displayed, you must watch for the F2 prompt to appear. Once the F2 prompt appears, press <F2> immediately.

  • Page 96: System Setup Screens

    System Setup Screens Menu — Appears on top of the System Setup window. This field provides a menu to access the System Setup options. Press < Left Arrow > and < Right Arrow > keys to navigate. As a Menu option is highlighted, the Options List lists the options that define the hardware installed on your computer.

  • Page 97: System Setup Options

    Keystroke Action – or + Change existing item value. < Enter > Select the sub menu or execute command. < F9 > Load setup default. < F10 > Save current configuration and exit System Setup. System Setup Options Main System Information Displays the computer model number.

  • Page 98

    System Memory Displays the memory in-built on the computer. Memory Speed Displays the memory speed. Device Information Fixed HDD Displays the model number and capacity of the hard drive. SATA ODD Displays the model number and capacity of the optical drive. eSATA Device Displays information about the installed eSATA device.

  • Page 99

    SATA Operation Change the SATA controller Default: AHCI mode to either ATA or AHCI. Adapter Warnings Enables or disables adapter Default: Enabled warnings. Function Key Behavior Specifies the behavior of Default: Function key first the function key <Fn> . Charger Behavior Specifies if the computer Default: Enabled battery will be charged...

  • Page 100

    USB Storage Device Specify which USB storage device the computer can boot through. CD/DVD ROM Drives Specify which CD/DVD the computer can boot through. eSATA Specify which eSATA device the computer can boot through. Network Specify which network device the computer can boot through.

  • Page 101: Diagnostics, Device Status Lights, Battery Status Lights, Diagnostic Beep Codes

    If the computer is connected to an electrical outlet, the battery light operates as follows: • Alternately blinking amber light and white light — An unauthenticated or unsupported non-Dell AC adapter is attached to your laptop. • Alternately blinking amber light with steady white light — Temporary battery failure with AC adapter present.

  • Page 102

    Beep Possible Cause Troubleshooting Steps BIOS ROM checksum in System board failure, progress of failure. covers BIOS corruption or ROM error No RAM detected No memory detected System board Failure • Chipset Error (North and South Bridge Chipset, DMA/IMR/ Timer Error) •...

  • Page 103: Specifications

    For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer. System Information Chipset: Vostro 3350/ 3450/ 3550/ 3750 Intel HM67 Vostro 3555 AMD A70M Processor: Vostro 3350/ 3450/ 3550/ 3750 •...

  • Page 104

    • discrete video card Video controller and memory UMA: Vostro 3350/ 3450/ 3550/ 3750 Intel Graphics Media Accelerator Vostro 3555 AMD Radeon HD series — up to 256 MB / 512 MB of shared memory Discrete:...

  • Page 105

    87 keys, and Japan: 90 keys Vostro 3750 United States: 101 keys United Kingdom: 102 keys Brazil: 104 keys Japan: 105 keys Layout QWERTY/AZERTY/Kanji Touchpad Active Area: Vostro 3350/ 3450/ 3550/ 3555 X-axis 80.00 mm Y-axis 40.70 mm Vostro 3750 X-axis 95.00 mm Y-axis 52.00 mm...

  • Page 106

    Display Active area (X/Y) 293.42 mm x 164.97 mm Dimensions: Height 189.00 mm (7.44 inches) Width 314.00 mm (12.36 inches) Diagonal 337.82 mm (13.30 inches) Maximum resolution 1366 x 768 pixels at 263 K colors Maximum Brightness 200 nits Operating angle 0°...

  • Page 107

    Display Pixel pitch 0.2265 mm Vostro 3550/3555 Type WLED display Size 15.6 inch HD Active area (X/Y) 344.23 mm x 193.54 mm Dimensions: Height 210.00 mm (8.26 inches) Width 360.00 mm (14.17 inches) Diagonal 396.24 mm (15.60 inches) Maximum resolution 1366 x 768 pixels at 262K colors Maximum Brightness 220 nits...

  • Page 108

    Refresh rate 60 Hz Minimum Viewing angles: Horizontal +/- 40° Vertical +10°/- 30° Pixel pitch 0.238 mm Battery Vostro 3350 Type • 4-cell "smart" lithium ion (2.8 AHr) • 8-cell "smart" lithium ion (2.8 AHr) Dimensions: Depth 4-cell — 43.45 mm (1.71 inches) 8-cell —...

  • Page 109

    Battery Depth 6-cell / 9-cell — 57.80 mm (2.27 inches) Height 6-cell — 20.80 mm (0.81 inch) 9-cell — 40.15 mm (1.58 inches) Width 6-cell / 9-cell — 255.60 mm (10.06 inches) Weight 6-cell — 340.00 g (0.75 lb) 9-cell — 504.50 g (1.11 lb) Voltage 11.1 VDC Vostro 3750...

  • Page 110

    Battery Operating 0 °C to 35 °C (32 °F to 95 °F) Non-operating –40 °C to ~65 °C (–40 °F to ~149 °F) Coin-cell battery 3 V CR2032 lithium ion AC Adapter Input voltage 100 VAC to 240 VAC Input current (maximum) 1.5 A / 1.6 A / 1.7 A / 2.3 A / 2.5 A Input frequency 50 Hz to 60 Hz...

  • Page 111

    Operating 0 °C to 35 °C (32 °F to 95 °F) Non Operating –40 °C to 65 °C (–40 °F to 149 °F) Physical Vostro 3350: Height 27.30 mm to 29.80 mm (1.07 inches to 1.17 inches) Width 329.20 mm (12.96 inches) Depth 228.50 mm (9.00 inches)

  • Page 112

    Physical Height 30.80 mm to 34.80 mm (1.21 inches to 1.37 inches) Width 418.40 mm (16.47 inches) Depth 286.70 mm (11.29 inches) Weight (Minimum) 3.00 kg (6.62 lb) Environmental Temperature: Operating 10 °C to 35 °C (50 °F to 95 °F) Storage -40 °C to 65 °C (-40 °F to 149 °F) Relative humidity (Maximum):...

  • Page 113: Contacting Dell

    Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: Visit support.dell.com. Select your support category.

Comments to this Manuals

Symbols: 0
Latest comments: