1. Manuals
  2. Brands
  3. El.Mo Manuals
  4. Keypad
  5. KARMA
  6. Technical manual

El.Mo KARMA Technical Manual

Touch screen control keypad
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Technical manual
KARMA
Touch screen control keypad
1
DESCRIPTION
KARMA is a touch screen control keypad.
The LCD display uses a resistive touch sensor.
Keypad elements:
• proximity keys reader for M4 keys
• PIR proximity sensor
• I66 connector for connection of an external reader
• USB connector for configuration and firmware updating
via BrowserOne
• slot for MicroSD card to store images to use in digital pho-
to frame mode
The interface includes menus for zone status visualisation
and sectors arming.
A configurable dashboard and a standard keypad emulation
interface are available.
The keypad can be used as digital photo frame.
The keypad can be connected over ULTRABUS RS-485 serial
line.
KARMA is compatible with:
Control unit
VIDOMO2K
PREGIO series
TITANIA series
PROXIMA series
ULTRABUS
®
advanced serial bus
Addressee for this information:
Firmware version
8.5.0 or above
2.7.0 or above
7 or above
1.0.2 or above
User |
Installer
2
KEYPAD VIEW
Front view, side view and rear view
120 mm
4
5
207 mm
1
Proximity sensor
2
LED indicators
3
Proximity keys reader
4
Protection against opening/removal from mounting surface
5
Hole for cable passage
6
USB connector
1 1 1
1
2
3
6
25 mm

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KARMA and is the answer not in the manual?

Questions and answers

Related Manuals for El.Mo KARMA

Summary of Contents for El.Mo KARMA

  • Page 1 Addressee for this information: User | Installer DESCRIPTION KEYPAD VIEW KARMA is a touch screen control keypad. Front view, side view and rear view The LCD display uses a resistive touch sensor. Keypad elements: • proximity keys reader for M4 keys •...

  • Page 2: Technical Data

    TECHNICAL DATA DEVICE MOUNTING Model KARMA • Opening the housing General features Display dimension Display resolution 800 × 480 pixels Operating voltage Power supply 12 (9 ÷ 15) Consumption at Display on 360,0 power voltage Display off 110,0 Standards compliant with...
  • Page 3 – draw the cover close to the base so that the spring pro- • 680 Ω termination resistors must be connected to the tecting against housing opening/removal fits correctly ends of the two longest branches Up to 4 KARMA keypads can be connected to VIDOMO2K and PREGIO series control units.

  • Page 4: Starting The Device

    – click on a tab – set parameters as indicated in the following paragraphs Once all changes have been done, write the new setup to the control unit. 6.1.1 Setup – join cover upper side and base upper side together: in- sert the tabs on base (A) into the slits on cover (B) Digital frame –...
  • Page 5 ▼ Load default Once KARMA has been configured, it will be possible to use Click to set the configuration to factory default. the USB port on side to connect the PC that runs BrowserOne ▼ Read setup to the control unit.

  • Page 6: Keypad Menu

    connected to the PC. – insert the MicroSD card in the PC – click on Images SD tab in the keypad configuration win- dow in BrowserOne (see paragraph 6.1  p. 4 ) The whole window enclosed in the rectangle (height a) will Add images be displayed in the digital photo frame menu.

  • Page 7: Zone Status

    Touch an icon to enter the corresponding menu. 20:50 08/10/18 20:50 Area 1 Area 2 08/10/18 Sector 2 Sector 1 Sector 1 Sector 2 S2.A1 S1.A1 S1.A2 S2.A2 Sector 3 Sector 4 Sector 3 Sector 4 S3.A1 S4.A1 S3.A2 S4.A2 Area 3 Area 4 Sector arming...

  • Page 8: Available Actions

    – open keypad configuration window in BrowserOne (see anomaly zone paragraph 6.1  p. 4 ) – click on Dashboard tab (see paragraph 6.1.2  p. 5 ) tampered zone Notes on menu visualisation in the dashboard: zone in alarm Sector arming If more than one areas are associated to the keypad, only bypassed zone in alarm the first will be displayed.

  • Page 9: Digital Frame

    Use BrowserOne to enable or disable user authentication MAINTENANCE request when an user tries to activate the output. If the authentication request has been disabled for KARMA keypads with firmware version 1.4.4 or higher, just one click Display calibration will enable the outputs, with no need for confirmation.

  • Page 10: Factory Default

    – select  Firmware update device option in menu Tools – select "USB" then select Next – select "KARMA" in drop-down menu then select Next In the next window:...

  • Page 12: Eu Declaration Of Conformity

    The information and product features herein are not binding and may be changed without prior notice. EL.MO. Spa - Via Pontarola, 70 - 35011 Campodarsego (PD) - Italy Ph. +39 049.9203333 - Fax +39 049.9200306 - Help Desk +39 049.9200426 - www.elmospa.com - international@elmospa.com...

Table of Contents