Advertisement
Food Service Pre-Rinse Assembly
Installation and Maintenance Instructions
FSB141
technical data
Working Pressure Range
Maximum Static Pressure
Maximum Working Temperature
Inlet Connection
Flow Rate
Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500.
Installations not complying with PCA and AS/NZS 3500 may void the product and performance warranty provisions.
Reference should also be made to the Australasian Health Facility Guidelines (AHFG), ABCB and Local Government
regulations when considering the choice of, and the installation of these products.
This product must be installed and commissioned by a qualified plumber.
For use with potable water only.
NOTE: Enware Australia advises:
1. Due to ongoing Research and Development, specifications may change without notice.
2. Component specifications may change on some export models.
I00220_09 Aug 2024
1300 369 273 | info@enware.com.au | enware.com.au
Min 50 kPa
Max 500 kPa
800 kPa
70°C
1/2" BSP
4 L/min (Pre-rinse spray gun)
5 L/min (Pot filler)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Watts ENWARE FSB141
- Page 1 Food Service Pre-Rinse Assembly Installation and Maintenance Instructions FSB141 technical data Working Pressure Range Min 50 kPa Max 500 kPa Maximum Static Pressure 800 kPa Maximum Working Temperature 70°C Inlet Connection 1/2” BSP Flow Rate 4 L/min (Pre-rinse spray gun) 5 L/min (Pot filler) Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500.
-
Page 2: Before Installation
installation BEFORE INSTALLATION • Ensure all operating and dimensional specifications are suitable for the intended installation. Check that there is no shelf or obstruction above. • Check that wall bracket can be installed on a stable wall surface. If not, extra measures may need to be taken so that the bracket can be supported by a firm wall backing. - Page 3 INSTALLING THE BASE - HOB DUAL MIXER 1. Mark the hole to be drilled on the bench and drill the hole using a hole saw or similar tool. SEE IMAGE 03 Drill hole position: min 40mm - max 155mm to the centre from wall Drill hole size: 33 - 35mm diameter Maximum bench thickness: 40mm...
- Page 4 INSTALLING RISER, POT FILLER & SPRAY ARM 1. Note that each component of the pre-rinse assembly uses a double O-ring spigot connection. The O-rings on the male spigot are pre-greased. Re-grease them if required. 2. Place the two white plastic washers below and above the pot filler as indicated, and assemble the pot filler onto the riser.
-
Page 5: Water Connections
5. Fit the hook onto spring retainer, then screw the hose onto the spring retainer. Use a thread sealant to seal the thread. Tighten using two spanners. SEE IMAGE 10 6. The O-rings on the top riser spigot have been pre- greased. - Page 6 operating instructions • Rotate the mixer handle to turn the water on to the trigger spray and pot filler • To turn on pot filler, rotate the lever handle to the right. PRE-RINSE TRIGGER SPRAY OPERATION • Squeeze spray trigger. Pull down hose to Squeeze desired angle and position to wash.
-
Page 7: Maintenance
maintenance CLEANING Enware products should be cleaned with a soft damp cloth using only mild liquid detergent or soap and water. Do not use cleaning agents containing a corrosive acid, scouring agent or solvent chemicals. Do not use cream cleaners, as they are abrasive. Use of unsuitable cleaning agents may damage the surface. -
Page 8: Troubleshooting
troubleshooting Refer to the following troubleshooting guide for specific problems and solutions. PROBLEM CAUSE RECITIFICATION No water flow from trigger Water supply turned off or Connect and turn on water supply spray outlet or pot filler spout disconnected Check valves are blocked by Remove check valves and clean debris Replace check valves (Located inside... -
Page 9: Spare Parts
spare parts FSBS002 FSBS001 FSBS003 FSBS005 FSBS002 FS729 FSBS008 FSBS007 SPARE PARTS FSBS001 Hose replacement FSBS002 SBA cold/pot filler FSBS003 SBA hot Handle assembly (each) FSBS005 FSBS007 Flexi hoses H&C (pair) FSBS008 Hose inlet extensions (pair) FS729 Pre-rinse gun FS734 O-rings (8), grub screws (4), &... - Page 10 dimensions HOT INLET COLD INLET www.enware.com.au Page 10 © Enware Pty Ltd...
-
Page 11: Product Warranty Statement
- WATTS AUSTRALIA EFFECTIVE FROM 20 November 2023 This Warranty Statement applies to products supplied by Australian Valve 3. Our responsibilities Group Pty Ltd (ACN 068 227 270) (AVG) or Enware Pty Ltd (ACN 662 (a) In the event that the Supplier is reasonably satisfied that there is a... - Page 12 1300 369 273 info@enware.com.au enware.com.au...
Need help?
Do you have a question about the ENWARE FSB141 and is the answer not in the manual?
Questions and answers