User Manual Content I. Exploded Diagram..............1 Installations& Adjusting ............2 III. Operation Instruction ............. 4 IV. Use & Maintenance ..............8 V. Trouble shooting guide ............. 10 VI. Schematic wiring diagram ............ 12...
User Manual I. Exploded Diagram Part Name Part Name Dispener Door Assembly Belt Dispenser Door Base Drive Pulley Operation Panel Proximity Switch Mix Level Probe Evaporator Hopper Compressor Feed Tube Electrical box Hopper Cover Condenser Plug of Feed Tube Beater Motor Coupling Drip Tray Gear Box...
User Manual II. Installations& Adjusting A、 unpack & inspect 1)Cut off the wrapping tape. 2)Open the wooden case by screwdriver. 3)Remove the foam. 4)Inspect carefully whether there is defective appearance or not. 5)Check the accessories with packing list. 6)Remove the fixing bolt and fixing feet that are at the bottom of the machine, push the machine, let the front-wheel drive fall to the ground, and then take out the wooden base, let the four wheels grounded.
Page 5
User Manual Caution: a、For safety, ensure the ground connection is in good condition. b、All the exterior wires and other appliances must confirm with national standard. C、 Testing Running 1) Switch “ON”the power switch and you will hear “Beep”,all the graphic patterns on the screen will be lighted up and then the graphic patterns will extinguish,machine enters “Standby”...
User Manual III. Operation Instruction A、 Key Instruction 1、display screen Figure.2 2、set key 3、adjust key(up) AUTO 4、adjust key(down) 5、standby key CLEAN 6、Wash key DOWN STANDBY 7、Auto key ◆ SET KEY(UP / DOWN) a、set hardness level: When the machine is ready mode, press “UP” or “DOWN” key for more than 2 seconds then the “SET”...
Page 7
User Manual Icon Implication Variable Range Periodic Restarting Time Seeting Range:5~15 minutes Stop Delay of Beater Motor Range:5~15 seconds No Specific Meaning Range:5~15 seconds Hopper Pre-cooling Temperature Seeting Range:10—80,indicates 1.0℃ ~8.0℃ Cylinder Temperature Setting Cleaning Frequency Range:2—14,indicates 2~14 days Lack Mix Alarming Time Setting Range:0—10 mins,”0”- Non-Stop Press “...
User Manual starts. The temperature of hopper and freezing cylinder can be directly displayed on the screen. ◆ AUTO KEY Press standby key, “AUTO”and“FRESH”icon will light. The little compressor for hopper is controlled by setting temperature. It will stop when the temperature is less than the setting value, and it will start again if the tempreature in hopper raise for 2℃.
Page 9
User Manual Less cooling,no cooling, or cooling over one hour still ice cream not forming, the screen will display”ERR”, and sound of “BEEP” will continue. B、 Make Ice Cream 1) MAKE SURE THE MACHINE IS CLEAN AND SANITIZED BEFORE MAKING ICE CREAM.
User Manual c、 Add more ice cream mixer into the hopper,put the hopper cover on..Press “ ” key to start operation.The number on the digital displayer will rise up during operation.When the number reach “99”, the ice cream in the freezing cylinder is ready for serve. d、...
Page 11
User Manual Fig.3 A 1、O-ring for dispenser door 2、 supporting sleeve 3、 dispensing door 4、modeling cap 5、down bolt 6、upper bolt 7、pin for handle 8、screw for handle 9、handle 10、O-ring for piston 11、piston 12、middle piston 13、O-ring for middle piston 14、beater 15、gasket for beater Fig.3 B 1、piston 2、O-ring for piston...
User Manual Notice: Before installing the piston, O-ring for piston, beater and gasket for beater, you should lubricate vaseline (lubricating vaseline onto the groove of the gasket, do not onto the beater’s end ), using the vaseline frequently can extend the service life of components. B、...
Page 13
User Manual The connecting wire is Check and fasten the wire. unfastened Machine clean Repair or change the beater The beater motor broke position does not run motor Mini circuit breaker was Find and solve the problem then broken. reposition it The wire of function switch Check and fasten the wire.
User Manual The touch point of the Remove the touch point or contact switch broke. change the contact switch. The proportion of mix is Make up a proper proportion of incorrect, and causes the mix. refrigeration difference No mix in the hopper Pour the mix into the hopper Product does...
Page 15
⚫ Technology parameters are on the nameplate ⚫ The electrical schematic diagram is on the board inner Marketed globally by: TRUFROST AND BUTLER PRIVATE LIMITED 1215, 12th Floor, Tower B, Emaar Digital Greens, Golf Course Extn. Road, Sector 61, Gurugram – 122011 (India) T.
Need help?
Do you have a question about the Butler Tom & Jerry Plus and is the answer not in the manual?
Questions and answers