Page 1
xstomobility.com User Manual Powered Wheelchair(Mobility Robot) M4 file number:D701000178 version number :B.3 Write the date:2024-6-11 Please read the manual carefully before using the product and keep it in a safe place.
Page 34
NOTICE——When driving up and down, the seat should handle the standard height position and should not rise to the highest state, otherwise there may be a danger of machine tipping.
Page 37
Unscrew the screws of the backrest support plate in the left picture, remove backrest support plate, and leak out of the back frame.
Page 39
Line the seat plate online and Seat slot move it out of the groove first. mouth Folding chair back, Standard is the lowest armrest position.
Page 40
Remove the screws indicated by the arrow in the left picture first,both side of handle’s need to be removed. Remove the screws on the left figure...
Page 41
Adjust to the required height align with hole position. Reinstall the screws that previously removed. Expand the back of the chair, find the position of the coil in the left picture, operate with both hands, push it down with one hand and pull down until the line length can be placed in the slot of the seat plate.
Page 42
Place the line in the seat plate slot as shown.
Page 43
Maintain the line seat plate in the groove, pull upward at the online end exit position that marked in the left figure, observe and press the line in the groove of the seat plate, pull the excess line length below the exit in the left Online end exit figure out of the exit.
Page 44
Fold down the backrest,return the screw on the left picture. When installing, ensure that the wires are close to the lower parts, as shown in the left figure, screws should slightly squeeze the wire...
Page 45
Expand the back and plug the line into the back frame.
Page 46
Install the clip screws for the wire here. Expand seatrest, reinstall the original back pad and put back the cushion.
Page 77
environment! NOTICE——When low charge, please charge in time! NOTICE——Please remove the equipment from oil, grease, detergents, diluents or anything that may be damaging! Warning——Except for seat cushion and backrest, if the parts are worn or need to be replaced, contact the dealer or the equipment may be damaged and operable.
Page 100
Figure 9.11 A Bluetooth search for a new device interface...
Page 135
or any others to comply with this rule. · Caution: Manufacturer will not responsible for any unauthorized actions that cause interference. · Caution: The M4 Mobility Robot cannot be used together with HF SURGICAL EQUIPMENT. Table 1 Guidance and Manufacture’s Declaration – Electromagnetic Emission The M4 Mobility Robot is intended for use in the electromagnetic environment specified below.
Page 136
Level c Environment - Guidance Floors should wood, concrete Electrostatic ±8kV contact ±8kV contact ceramic tile. discharge (ESD) ±2kV, ±4kV, ±8kV, ±2kV, ±4kV, Humidity IEC 61000-4-2 ±15kV air ±8kV, ±15kV air should be at least 30% if it is synthetic materials.
Page 137
interruptions cycle 250/300 cycle continuously. IEC 61000-4-11 Power frequency magnetic fields should be at RATED power levels frequency 30A/m 30A/m characteristic magnetic fields 50Hz or 60Hz 50Hz or 60Hz typical IEC 61000-4-8 location in a typical commercial or hospital environment. 65A/m, Modulation: 65A/m,...
Page 138
Note: UT is the A.C. mains voltage prior to application of the test level. Table 3: Guidance & Declaration - electromagnetic immunity concerning Conducted RF & Radiated RF Guidance & Declaration - Electromagnetic immunity The M4 are intended for use in the electromagnetic environment specified below.
Page 139
IMMUNITY to PORT IMMUNITY performance this equipment RF wireless to RF wireless communication communication could result. equipment equipment (Refer (Refer to table 9 to table 9 of IEC of IEC 60601-1- 60601-1- 2:2014+A1:2020) 2:2014+A1:2020) Table 4 -Test specifications for ENCLOSURE PORT IMMUNITY to RF wireless communications equipment...
Page 140
Table 5 - Test specifications for ENCLOSURE PORT IMMUNITY to proximity magnetic fields...
Page 144
xstomobility.com +86-760-28207258 info@xstomobility.com Floor 1, Building C, 555 Plant. Ma’an Cun Rd, Cuiheng New District, Zhongshan City, Guangdong, China...
Need help?
Do you have a question about the Mobility Robot M4 and is the answer not in the manual?
Questions and answers
Accaunt aanmaken voor XSTO M4