Summary of Contents for Gorilla Playsets 02-3003
- Page 1 ™ ™ playsets playsets Children’s Picnic Table Model: 02-3003 Copyright © 2023 Gorilla Playsets All Rights Reserved *51-3003* 166 Etowah Industrial Court Canton, GA 30114 www.gorillaplaysets.com REV A: 4/28/2023 51-3003...
- Page 2 Please inspect and inventory all parts immediately upon accepting delivery. Use the inventory pages in the manual to make sure you have received all necessary parts. The quickest method to get any parts that are missing or damaged is to use our “Quick Response Center”...
- Page 3 This decision is subject to verification of the defect, which, at Gorilla’s discretion, may be accomplished by submitting photographs or by delivery of the defective part to Gorilla Playsets • 166 Etowah Industrial Ct. • Canton, GA 30114 • 1-800-882-0272 Monday to Friday 9AM-5PM EST. Any warranty claim must include proof of purchase, including the date of purchase.
-
Page 4: Important Safety Guidelines
Gorilla shall not be liable for incidental, indirect or consequential damages or injuries that result from building and/or playing on our play sets. Adult supervision is recommended anytime a play set is being used. WEIGHT LIMITS FOR GORILLA PLAYSETS • FORT PLATFORMS: 800 LBS. TOTAL WEIGHT • SWING BELT: 225 LBS. - Page 5 PRODUCT REGISTRATION - CHILDREN’S PICNIC TABLE - Gorilla Playsets manufactures ™ 3 EASY WAYS TO REGISTER the finest quality products that are designed for outstanding Complete the online registration form at: OPTION 1 https://www.gorillaplaysets.com/product-registration strength and durability. We back our products with unparalleled...
- Page 6 THIS PAGE INTENTIONALLY LEFT BLANK...
-
Page 7: Important - Please Read
IMPORTANT – PLEASE READ Congratulations! You have just purchase one of the finest residential wooden swing sets available today. As with any wooden product that spends its entire life outside, in varying elements, it is important to know what to expect with your new swing set so that your family can enjoy it for many years. -
Page 8: Important Documents
. . Gorilla Playsets 166 Etowah Industrial Court Canton, GA. - Page 9 Picnic Table Hardware REV: A 7/11/2013 JH #8 x 1-3/4" WOOD SCREW QTY: 10 #8 X 2" WOOD SCREW QTY: 38 5/16" T-NUT QTY: 12 5/16" WASHER QTY: 12 5/16 X 2" HEX BOLT QTY: 12 #2 SQUARE DRIVE BIT QTY: 1 USE THE RULER TO THE RIGHT TO MEASURE YOUR BOLTS AND SCREWS.
- Page 10 PICTURE DESCRIPTION QTY. 2 X 4 X 23-13/16" TABLE LEG 2 X 4 X 21" TABLE STRINGER 2 X 4 X 21-1/2" ANGLE SUPPORT 2 X 4 X 21-3/8" TOP LEG SUPPORT 2 X 4 X 42" CENTER LEG SUPPORT 2 X 4 X 42"...
- Page 11 PICTURE DESCRIPTION QTY. 2 X 6 X 47-5/8" TABLE SEAT 5/4 X 5 X 47-5/8" CENTER TABLE 5/4 X 5 X 47-5/8" TABLE TOP UMBRELLA ASSEMBLY...
-
Page 12: Step 1: Leg Assembly
STEP 1: LEG ASSEMBLY 1: FIND TWO 2 X 4 X 23-13/16" TABLE LEGS. NOTE THE HOLE PATTERN ON THE LEGS AND POSITION THEM SO THAT THE END WITH ONE HOLE WILL BE AT THE TOP. THE ORIENTATION OF THE LEGS SHOULD LOOK LIKE THE SIDES OF THE LETTER "A". 2: DETERMINE WHICH SIDE WILL BE FACING THE INSIDE OF THE TABLE AND PLACE A T-NUT IN EACH OF THE HOLES. - Page 13 STEP 2: CENTER LEG SUPPORT 1: FIND THE 2 X 4 X 42" CENTER LEG SUPPORT. TAKE NOTE OF THE TWO HOLES DRILLED IN EACH END OF THE BOARD. ALSO THE ROUNDED OVER EDGE ON THE LARGE HOLE AT THE CENTER OF THE BOARD SHOULD FACE UP.
-
Page 14: Step 3: Table Top
STEP 3: TABLE TOP 1: FIND ONE 5/4 X 5 X 47-5/8" CENTER TABLE TOP BOARD AND FOUR 5/4 X 5 X 47-5/8" TABLE TOP BOARDS. THE CENTER BOARD WILL HAVE A HOLE DRILLED ON-CENTER IN THE MIDDLE OF THE BOARD, AND ALL OF THE BOARDS WILL HAVE PRE-DRILLED HOLES IN EACH END. 2: CENTER THE HOLES IN THE CENTER TABLE TOP BOARD OVER THE CENTER OF THE TOP LEG SUPPORTS AND ATTACH WITH 2"... - Page 15 STEP 4: TABLE STRINGER 1: FIND THE 2 X 4 X 21" TABLE STRINGER. NOTE THE ANGLED ENDS OF THE BOARD, AND THE HOLE IN THE CENTER. 2: POSITION THE TABLE STRINGER SO THAT THE HOLE IN THE CENTER OF THE BOARD LINES UP WITH THE HOLE IN THE CENTER OF THE PICNIC TABLE, AND THE ANGLED ENDS ARE FACING DOWN.
- Page 16 STEP 5: ANGLE SUPPORTS 1: FIND TWO 2 X 4 X 21-1/2" ANGLE SUPPORTS. NOTE THE ANGLED ENDS OF THE BOARDS. 2: POSITION THE ANGLE SUPPORTS SO THAT THE LONG ANGLED END OF THE BOARD IS RESTING AGAINST THE BOTTOM OF THE TABLE TOP. THE BOTTOM END WILL REST UPON ON THE CENTER LEG SUPPORT AND WILL BE FLUSH TO THE SEAT SUPPORT.
- Page 17 STEP 6: SEATS 1: FIND THE 2 X 6 X 47-5/8" TABLE SEATS. NOTE THE PRE-DRILLED HOLES ON EACH END. 2: CENTER THE SEATS AT THE ENDS OF THE SEAT SUPPORTS AND ATTACH WITH 2" WOOD SCREWS IN THE PRE-DRILLED HOLES. 2"...
- Page 18 UMBRELLA ASSEMBLY 1: SCREW THE UPPER PORTION OF THE UMBRELLA ONTO THE LOWER PORTION OF THE UMBRELLA. 2: RAISE THE ROSETTE OF THE UMBRELLA, THEN INSERT THE PIN INTO THE HOLE. WHEN NOT IN USE THE UMBRELLA SHOULD BE IN THE DOWN POSITION. IN THE WINTER REMOVE THE SET SCREW COLLAR FROM THE LOWER SECTION OF THE UMBRELLA AND STORE THE UMBRELLA AWAY IN SAFE LOCATION.
Need help?
Do you have a question about the 02-3003 and is the answer not in the manual?
Questions and answers