Patterson Medical 09 107 6801 Quick Start Manual

Tooting Shower Seat / Siège de douche à lattes Tooting
NEW CODE ol D Co De
09 107 6801 aa 1690
09 107 6850 aa 1694
09 107 6884 aa 1697
Intended uses
• To compensate for a disability by providing a
seat for a person taking a shower
Instructions for use
1. The seat can be folded up out of the way when
not in use. Be sure the latch holds the seat
securely up.
2. To lower the seat, hold onto the cross bar
between screws D, and pull out from the wall.
Cautions
• Do not pull on the legs to lower
or raise the seat.
• s hower seats should be installed by a
professional.
• s hower seats should not be attached to plastic
shower walls, stud partitioning, plasterboard-
type cavity walls, or any similar type of shower
surround or wall.
• t he shower seats are not to be used to
support more than 158kg / 348lb. / 24¾ st.
• t he seats are not to be used with water that
is colder than 5°C / 40°F or hotter than 50°C /
120°F.
• Be sure the seat is securely in place before
putting weight on it.
• u se of a slip-resistant bath mat is strongly
recommended.
• Cover the seat with a towel to help reduce
slipperiness.
Manufactured for Patterson Medical Ltd.
Nunn Brook Road, Huthwaite,
Nottinghamshire,
NG17 2HU, UK.
UK: Tel: 08444 124 330 Fax: 08448 730 1000
www.pattersonmedical.co.uk
International: Tel: +44 1623 448 706
Fax: +44 1623 448 784
Patterson Medical Products, Inc.
1000 Remington Boulevard, Suite 210,
Bolingbrook, IL 60440-5071, USA.
Tel: 1-800-323-5547 Telefax: 1-800-547-4333
© Patterson Medical Ltd. 2013
70058 Is13
Instructions for installation
1. These seats should be installed by a
professional, who will choose hardware
appropriate for the
n ote that each individual
a shear force of 60 kg / 130 lb. and a pull-out
force of 20 kg / 45 lb.
2. Remove the screws that are labelled C in the
drawing from each block (B) and loosen the
screws that are labelled D.
3. Slide the legs into the blocks and tighten screws
D. Screws C can be left out at this stage.
4. Establish the height of the seat, which can be
adjusted from 460 to 590 mm / 18 to 23 inches
as follows:
a. With the seat in the horizontal position,
position the rear brackets (E) against the
shower wall.
b. To adjust leg length, remove the four pin clips
(A) from the legs, determine the appropriate
length, and replace the pin clips.
c. Be sure both legs are adjusted to the same
height. A gap up to 5 mm /
one leg is acceptable. However, if the angle
of the shower tray results in a greater gap,
the seat must be installed at an angle to
compensate for it.
Please retain these instructions for future reference.
Patterson Medical Australia
PO Box 1006, North Ryde, NSW Australia 2113.
Tel: 1300 473 422 Fax: 1300 766 473
Patterson Medical France
Zone Industrielle de Montjoly
11 Avenue de I'Industrie - CS 40712
08013 Charleville-Mézières Cedex, France.
Tel: 03 24 52 6 115 Fax: 03 24 529 034
5. Mark the lower securing holes through the rear
brackets. All
be used. Remove the seat from the wall and drill
and plug the wall.
installation.
6. Loosen the screws D and remove the legs
should resist
from the seat.
7. With the seat locked in the vertical position,
position the rear brackets over the holes and
fasten the seat to the wall.
8. Slide the legs back into the blocks and line up
the leg securing holes. Replace and tighten
screws C, and tighten screws D in the blocks.
Care and Cleaning
The seat can be cleaned with mild detergent
and water.
3
/ " inch under
16
holes in the rear bracket must