Subscribe to Our Youtube Channel
Related Manuals for El.Mo MDGSME
Summary of Contents for El.Mo MDGSME
- Page 1 MDGSME GSM GPRS dialler module 0900A0872 For installation inside TA1002, TA1004, TA2000, TA4000: Declaration of Performance nº 0051 – CPR – 0405 Standard EN54-21:2006 In reference to the BGS2-E GSM module used...
- Page 2 (explosion and fire). EU DECLARATION OF CONFORMITY Hereby, EL.MO. S.p.A., declares that the MDGSME radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: elmospa.com – registration is quick and easy.
- Page 3 Technical manual; nylon fixing clips; kit with 3MA screws, 3MA nuts and spacers; cable tie; protective sleeve. Note: to install MDGSME on a Tacóra series control unit, a GSMACI antenna kit is required. The kit includes the CPR label, stick it to the housing of the control unit as described below.
-
Page 4: Installation
While installing the module, also follow the directions and general information found in the manual of the compatible control unit. Note: when installing MDGSME in a vehicle, use the screws, spacers and nuts to fix the module to the main board of the control unit, instead of the standard nylon clips. - Page 5 0900A0872 - TECHNICAL MANUAL - MDGSME 3.1 Board view 3.2 SIM preliminary operations international@elmospa.com elmospa.com...
- Page 6 MDGSME - TECHNICAL MANUAL - 0900A0872 3.3 Antenna installation 1. Pass the threaded pin of the piece marked “A” through 5. Screw the bracket to the wall or to any other suitable the hole in the bracket and keep it in position.
- Page 7 0900A0872 - TECHNICAL MANUAL - MDGSME 3.4 MDGSME module installation Use the slot marked “C” on the main board of the control unit: “C” mark Place the nylon spacers where shown above, clicking them into position. If encountering any resistance while trying to push the clips on the tip of the spacer past the board, keep them pressed together with thin-nose pliers rather than forcefully pushing the spacer.
- Page 8 MDGSME - TECHNICAL MANUAL - 0900A0872 Turn the module parallel to the main board and push it down to have the spacers click (use the pliers again if need be) and to firmly plug the connector: Insert the protective sheath around the module cable, as shown below: international@elmospa.com...
- Page 9 0900A0872 - TECHNICAL MANUAL - MDGSME Hand-tighten the module cable and the antenna cable. Hold both by the metallic part (do not twist the cable): Keep tightening the cables using 8 mm and 13 mm wrenches: 8 mm 13 mm international@elmospa.com...
- Page 10 Install any other modules, then power up the control unit. Do not power up the control unit after the MDGSME module has been installed if the external antenna has not been connected. Note: to install the module in a Tacóra series control unit, follow the instructions provided with the GSMACI kit.
-
Page 11: Maintenance
Do not spray directly on the case or on the display. • Periodically check if the antenna is properly attached to the cable connector coming from the MDGSME module. - Page 12 The information and product features herein are not binding and may be changed without prior notice. EL.MO. SpA Via Pontarola, 70 - 35011 Campodarsego (PD) - Italy Tel. +390499203333 - Fax +390499200306 - Technical Ass. +390499200426 - www.elmospa.com - international@elmospa.com...
Need help?
Do you have a question about the MDGSME and is the answer not in the manual?
Questions and answers