TRENDnet TEG-PCBUSR User Manual
  1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Computer Hardware
  5. TEG-PCBUSR
  6. User manual

TRENDnet TEG-PCBUSR User Manual

32-bit cardbus 10/100/1000mbps gigabit ethernet pc card
Hide thumbs Also See for TEG-PCBUSR:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Installation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TEG-PCBUSR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for TRENDnet TEG-PCBUSR

Summary of Contents for TRENDnet TEG-PCBUSR

  • Page 2: Table Of Contents

    Table Of Contents FCC Warning This equipment has been tested and found to comply with INTRODUCTION ..............1 the regulations for a Class B digital device, pursuant to Part ............1 ENERAL ESCRIPTION 15 of the FCC Rules. These limits are designed to provide LED I ..............

  • Page 3: Introduction

    Card provides the following features: Complies with IEEE 802.3 10BASE-T Ethernet standard The 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card is a credit-card sized Fast Ethernet adapter for Complies with IEEE 802.3u 100BASE-TX Fast Ethernet connecting a notebook to an IEEE 802.3 Ethernet network, standard IEEE 802.3u fast Ethernet and IEEE 802.3ab Gigabit...

  • Page 4: Card Insertion And Removal

    Find/select an available Type II or Type III 32-bit PC Card slot on your notebook’s side or rear panel. Holding the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card with the LED indicator facing up then insert to the 32-bit PC Card slot. Slide the 32-bit CardBus 10/100/1000Mbps Gigabit Ethernet PC Card all the way into the 32-bit PC Card slot until it reaches a firm stop.

  • Page 5: Driver Installation

    Before connect 32-bit CardBus This section will lead you to install the utility of the Gigabit 10/100/1000Mbps Gigabit Ethernet PC Card to the LAN PC Card. network, you have to install the network driver first. The driver for each networking operating system is under a Windows Utility Installation separate directory.

  • Page 6: Onfiguration The Pc Card

    Configuration the PC Card change the VLAN ID of existing VLAN. General Add: Click the Add button to specify the VLAN ID to this adapter. Delete: Select existed VLAN ID setting and click the Delete button to delete the VLAN ID setting.
  • Page 7 Flow Control This section displays working parameters for this network adapter. One can modify these parameters here. For Windows 98SE and ME, it needs to reboot to change the parameters. Modify: Select the working parameter setting which you The Flow Control allows user to minimize possible data want to modify, then click Modify button to change the loss during transmission on the network.
  • Page 8 The Network Address allows user to change the physical Link Speed/ Duplex Mode address of your adapter. To set up a physical address, type any new address in the value field and click Modify button to save your MAC address. This figure displays a modified network address “1A2B3C4D5E6F”.
  • Page 9 Modify button to confirm. Wake-On-Lan After Shutdown The Offload Checksum allows user to decrease CPU utilization by offloading the task of CPU to the network adapter. The Wake-On-Lan after Shutdown allows user to To configure this setting, select a value from the remotely power on and manage your computer.
  • Page 10 If got the Fail record, please contact Cable your vendor. The section shows you the result of a single test run. This section displays the cable connection information of the selected network adapter. It shows the length and User can check the “Repeat”...

  • Page 11: Technical Specifications

    IEEE 802.3ab 1000BASE-T Gigabit Ethernet ANSI/IEEE Auto-Negotiation 32-bit CardBus PC Card Protocol CSMA/CD This section allows user to wake up remote computer by Ethernet Address, IP Address or NetBIOS Name through Ethernet: 10Mbps (half-duplex) Data Transfer selected network adapter. Rate...

  • Page 12: Limited Warranty

    WITH SALE, INSTALLATION, warranty is voided if (i) the product has been modified or repaired by any MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION unauthorized service center, (ii) the product was subject to accident, abuse, OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY...

Table of Contents