Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Star 56
- Page 1 USER MANUAL Model: Star 56 Power Pack Star Universal (Gosport) Ltd Unit 2, Clarence Wharf, Mumby Road, Gosport, Hampshire, United Kingdom, PO12 1AJ Tel: + 44 (0) 23 9258 2857 Fax: + 44 (0) 23 9251 1731 Email: sales@staruniversal.com Web: www.staruniversal.com...
- Page 2 Star Universal (Gosport) Ltd cannot be held responsible for eventual damage caused by specifications deviating from the standard model. Although extreme care has been exercised during the writing of this manual, Star Universal (Gosport) Ltd will not accept any liability for eventual errors in this manual and/or for the consequences of (mis)interpretation of the contents.
-
Page 3: Table Of Contents
With the purchase of this heat sealing machine you will be able to pack a great variety of products. Star Universal (Gosport) Ltd has ensured that all the machines, from the smallest to the largest model, fulfil the greatest demands. All the machines are built in-house to the highest standards and undergo vigorous testing. -
Page 4: Safety Instructions
Ensure the power is switched off and the plug removed from the socket prior to carrying out any service work. The machine should be regularly serviced using genuine Star parts and is subject to the portable appliance test regulations. When not in use switch the machine off. -
Page 5: Machine Settings
MACHINE SETTING 56/56C Weld Control Keypad Locked Cool Control Power On Indicator Alarm Indicator SETTING THE WELD AND COOL TIMES/TEMPERATURES. Set the weld and cool times as below. Place some of the material you wish to seal between the sealing jaws, close them and cycle the machine by pressing the foot switch/push button. When the cycle finishes open the jaws, if the material has not welded increase the weld and cool times. - Page 6 Key Lock To prevent unauthorised alteration, the Star MkVI has a control lockout. If the green keypad locked light is on the feature is not engaged. To engage or disengage press the cool ▲ or ▼ key and release to display the cool time, the blue indicator will flash.
-
Page 7: Error Codes And Fault Finding
• • Jaws timeout too low Increase jaws timeout (see p6) (Jaws failed to close after • • Board fault Replace board/contact Star universal start signal received) • • Broken element Replace element (no power detected across • •... -
Page 8: Inside The Machine
INSIDE THE MACHINE Circuit Board NB: Red Links must be on AC Suppressors Relay Weld Relay Transformer Cabling to socket in lid... -
Page 9: Electrical Parts List
(Temperature control model) B012002 Rubber Foot ALL PARTS QUOTED IN THIS MANUAL ARE CORRECT AT THE TIME OF PUBLICATION E&OE STAR UNIVERSAL RESERVE THE RIGHT TO REVIEW AND ALTER THE PARTS AS NECESSARY COMPONENTS AND LAYOUT MAY VARY FROM THOSE PICTURED... -
Page 10: Wiring Diagrams
WIRING DIAGRAM... - Page 11 115V Modification...
-
Page 12: Technical Specification
As Star Universal only build industrial equipment to individual customer requirements the responsibility for the disposal lies with the end user. Star Universal will offer a collection service for machines we have built at the end of their useful life for recycling. -
Page 13: Warranty Policy
STAR UNIVERSAL WARRANTY POLICY The Company provides a 1-year warranty from the date of delivery on all Star Heat Sealing machines. If any part is found defective due to faulty manufacture, Star Universal will affect the repair or replacement to the customer free of charge providing: a) The fault is reported directly to the Service Department. - Page 14 Star Universal (Gosport) Ltd Unit 2, Clarence Wharf, Mumby Road, Gosport, Hampshire, United Kingdom, PO12 1AJ Tel: + 44 (0) 23 9258 2857 Fax: + 44 (0) 23 9251 1731 Email: sales@staruniversal.com Web: www.staruniversal.com...
Need help?
Do you have a question about the 56 and is the answer not in the manual?
Questions and answers